Homemade Circular Saw Guide / DIY Track Saw
Вставка
- Опубліковано 11 лют 2021
- #circularsawguide #tracksaw #sawguide
Hi. In this video, I tried to demonstrate two very useful, cheap and simple "Circular Saw Guides" constructions. One of the guides I made using laminate parquet boards and aluminum lath is 120cm and the other is 240cm long. When using this guide, you don't have to attach any parts to your circular saw. You make the adjustment, place the saw on the tray and you can cut.
You can access the 3D plan drawn in exact dimensions from the link I gave below. If you have any questions, be sure to write them in the comments section and I'll try to answer them. Other videos on my channel will also interest you, don't forget to watch.
If you liked the video, don't forget to press the "Like" button, "Subscribe" to my channel and press the "Bell" notification to be notified of my other videos.
PDF
drive.google.com/file/d/1B7DN...
3D PLAN
drive.google.com/file/d/13LiS... - Навчання та стиль
![circular saw guide track jig for precise cutting [woodworking]](http://i.ytimg.com/vi/ffckNf8y3mE/mqdefault.jpg)
This is just about the best home made track saw I’ve seen yet.
Thank you very much. I'm glad you liked it. You know you can find PDF plans in all my videos, right?
Больше спасибо всем умельцам ,
в том числе и тебе за дельные выдумки. Я по профессии ни столяр, ни плотник , но по необходимости и по влечению приходится заниматься этой работой . И мне здорово помагает такое видео . Спасибо.
Я тоже благодарю вас. Я тоже не плотник. Но мне нравится иметь дело с этими вещами.
Thank you very much for these videos on rip cut and cross cut for circular saw. I was thinking of buying a circular saw to make boxes and other things. But I was scared of how hard it would be to do straight cuts at 90 degrees. You solved a big problem for me. I will make a video with your plans and link you in it, in 1~2 months. If I have any questions, I will post them here. I'll make something similar for my router as well for a planing sled to make the top surface flat.
Hello there. First of all, thank you for your interest. The reason why I made these tools was the need for straight cutting. This was a really important and big problem. One tool I made became a cutting bench for another. I've made my workshop quite a tool holder. My goal is not just to make tools. Then I'm thinking of making some items for my house using these tools. Please keep following me and don't forget to activate the bell notifications.
Perfect project! I like the idea that the saw tray is not fixed to the saw base so that you can put it in and out in an instant, when needed. Im going to make exactly same one for my self. Thank you for sharing!!!
Hello. I am so glad you liked it. I chose this method because I thought like you. Thank you for your interest and comment.
Brilliant, cheap solution to getting straight cuts with a circular saw. Laminate flooring is a very flat and stable material to use. Thanks for sharing.
Hello. I am very pleased. As you said, it's a cheap and effective solution. One feature of this app is that there are no parts that need to be attached to the saw. Thank you for your interest and comment.
This is a great design- definitely one of the best I've seen. Not complicated, and well worth taking the time to make. Great video.
Thank you so much. I'm glad you liked it. You can find detailed measurements in the description section of the video 👍
Foi o melhor projeto de guia para Serra circular que eu já vi, parabéns!
Muito obrigado. Estou feliz que você gosta. Você pode baixar as dimensões para este projeto e meus outros projetos na seção de descrição.
Еще и еще раз сердечное СПАСИБО за отличные ролики! Я пенсионер и покупать магазинную оснастку для работы не могу - очень дорого. А благодаря ВАМ потихоньку делаю по дому и себе, и дочке с внуками много полезных вещей. Спасибо Вам, добрый, хороший человек!
Я так рад. Большое вам спасибо. За ваш интерес и приятный комментарий ... Я осознал некоторые свои ошибки в отношении безопасной работы. Пожалуйста, берегите себя во время работы. Я желаю тебе хорошего дня
I just made one for my circular saw. It has made the circular saw a more effective tool. Thank you for sharing your thoughtful design. It was great not to modify the saw to have this guide.
I try to make designs as much as I can without drilling holes or adding anything to the tools. Thank you for your interest. Greetings from Turkey 👍
İzlediğim en yalın en kolay uygulamalı ve en; tatil fayda sağlayan klavuz çalışması olmuş. Eline emeğine teşekür ederim
Teşekkür ederim Rıfat bey. Begenmenize sevindim. Ölçüleri açıklama bölümünde bulabilirsiniz. Hayırlı akşamlar
I have looked at several track saw units. Yours was the better or best of them. I looked at 4, and yours was detailed and done with a lot of thought. Thank you for PDF for how to…
I thank you too. For your interest and nice comment. You can find the measurements in PDF format in all my videos. I wish you healthy days
Those "cut in half" holes are a genius solution. Bravo , very inspiring to make one my own because I have a circular saw without a guidetrack 🙋
Hello. Thanks. I'm glad you liked it. You know you can find PDF plans in all my videos, right?
What are the cut holes for? I was trying not to have to ask didn’t want to come off sounding dumb but for the life of me I can’t figure it out.
@@hectorgrande8000 The half holes are made so you can lay the sawguide on your marked line. The edges of the half holes are the guidepoints to see if you are exactly on the marked line.
I was thinking of another slightly more complex design, but yours' simplicity wins all the prizes. Congratulations, excellent work.
Thanks for sharing, greetings from Argentina.
Thank you very much. I'm glad you liked it. It is really good to use without interfering with the circular saw.
Paylaşımların için teşekkür ederim. Özellikle de planları da bizlere sunduğun için ayrıca tebrik ediyorum.
Ben de size teşekkür ederim Alper bey. Bütün videolarımda ölçüleri açıklama bölümünde bulabilirsiniz. Hayırlı geceler
Fantastic! by far the best saw guide, period.
Thank you so much. I'm glad you like it 👍
Yapımı çok basit ama çok kullanışlı ve vazgeçilmez bir cihaz. İyi iş. Sen gerçek bir ustasın. Rusya'dan selamlar.
Çok teşekkür ederim. Beğenmenize sevindim. Çok işe yarıyor gerçekten. Türkiye'den selamlar
Спасибо большое!
Очень просто и надёжно. Я хочу распилить мдф щиты для того чтобы собрать кухню. Благодаря Вашему видео у меня это получится проще и точнее.
Спасибо!!!
И тебе спасибо. Рад, что смог тебе помочь.
Молодец! Спасибо за идею "каретки", удобно, что к пиле не надо направляющие прикручивать, потом откручивать.
То же. Это действительно обеспечивает большое удобство. Спасибо за ваш комментарий и интерес.
да, это правильно подмечено- тут самая правильная и ценная идея- это "каретка", именно это очень удобно
Большое спасибо👍Отличная идея с соединением ламината для увеличения длины😏
Я тоже благодарю вас. Мне нравится использовать ламинат. слияние очень хорошее и гладкое. Я использовал ламинат во многих проектах.
every thing you create is simple and very efficient. And it is why it is so efficient and so good,
you are one of the best DYI ! And I mean it!!!! I like your UA-cam channel!
Thank you for your nice and motivating comment. I will post a new video today. I think you will like it too. Don't forget to turn on bell notifications. have a nice day
Excelente trabajo. El PDF genial. Gracias. 💪 👏 👏 👏 👏
Hola. Puedes encontrar las medidas en formato PDF en casi todos mis videos. Sigue siguiéndome y no olvides activar las notificaciones de campana.
Muy buen video y sobretodo Gracias por el pdf, hay muchos proyectos que nos dan una idea pero no mucha información, pero con tu pdf, esta de lujo Gracias y Saludos
Intento compartir medidas en todos mis videos. Gracias por su atención
Very good job , thank you very much for sharing your knowledge
Thank you too 👍
Excelente!!!!
Saludos desde Argentina
Gracias por compartir ideas y tu experiencia, saludos.
Gracias por su interés. Estoy muy feliz de que te haya gustado. Por favor, continúe siguiéndome.
Tebrikler çok pratik ve kullanışlı olmuş. Elinize sağlık.
Çok teşekkür ederim Bilal bey
Great design, good job! One suggestion...instead of sandpaper, try using the foam rubber mat that you get for the bottom of toolbox drawers, it tends to grip a lot better and doesn't leave sandpaper marks on your wood finish :)
Thank you so much. Your recommendation is an excellent idea. Honestly, it never occurred to me.
@@MuratGuney Jjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjj
Блестяще! Всё просто и наглядно!
Большое спасибо. Я рада что тебе нравиться. 👍👍👍
So far, the best guide I've seen
Thank you so much. Your comment made me very happy. I recommend you to watch my other videos as well. I wish you healthy days.
Yes i agree and i will copy this tks.
This is exactly what I am looking for,
gonna build one for myself these days...
Thank you very much!
Çok teşekkür ederim
I thank you too. I'm glad you liked it. I would like to remind you that you can find the PDF plans in the description section of all videos.
Ellerine Sağlık Kardeşim Seni gördükçe hevesim artıyor. Allah Razı Olsun.
Çok teşekkür ederim. Kendi yaptığım aletleri kullanmayı seviyorum
Great video, great channel!
I wonder, how I didn't meet this channel before?!
Murat, thank you for such a quality and interesting content.
Btw, I have few old wide-n-long laminate boards - so, adding these saw guides a into my todo list.
First of all, thank you very much. This guide was one of the first equipment I made and I still use it. Thanks to this guide, I was able to make other tools... I would like to remind you that you can find PDF plans in all my videos. Greetings from Turkey
Thank you I will imitate your design circular saw guide. I saw your video from Java-Indonesia.
Thank you for your interest. It's a really useful tool. I wish you healthy days...
@@MuratGuney you're welcome.🙏🙏🙏
Kanalınızı buğün keşfettim Elinize sağlık. Evde bulunabilecek malzeme dar imkanlarla kolayca yapılabilir çözümler sunuyorsunuz çok hoşuma gitti. Umarım videoların devamı gelir.
Çok teşekkür ederim. Dediğiniz gibi herkesin ulasabilecegi, elinde olmasa bile çok para harcamadan satın alabileceği malzemeleri kullanmaya çalışıyorum. Bunun yanında yaptığım aletleri aktif olarak kullanıyorum. Elimden geldiğince aklımdaki projelerin videolarını koymaya çalışacağım. İlginiz için tekrar teşekkür ederim...
Encore merci beaucoup pour les vidéos et les plans
Merci encore aussi. Salutations de la Turquie
Самый лучший вариант! Спасибо, Мастер!
Большое спасибо. Я рад, что тебе понравилось. Пожалуйста, продолжайте следить за мной
@@MuratGuney Обязательно, буду следить!
Спасибо ... 👍
@@MuratGuney что за профиль используете?
Привет. Я использую алюминиевый профиль, называемый С-образным профилем. Если этот профиль не найден, его можно заменить на аналогичный. или ламинат можно использовать, нарезав тонкие рейки.
Lo mejor de lo mejor gracias x compartir tus conocimiento es la mejor guia q he visto hasta el momento. Gracias mil
Un suscriptor mas a tu pagina
Estoy tan contenta de que te haya gustado. Puedes encontrar las medidas en la sección de descripción de todos los videos. Gracias
At last, a track guide easy to make! You have got a new subscriber.
Thank you. I'm glad you like it. It is really useful
wow!! excelente trabajo👏👏👏👏👏👍
Gracias. Me alegro que te haya gustado. Estoy seguro de que también te gustarán mis otros videos. 😀👍
Thank you! It looks perfect to me. I'll follow your instructions.
Thank you too. This was the first proper cutting tool I ever made and I still use it. Later, I cut the necessary parts for the other tools I made using this guide. I made another guide to make cuts longer than 2 meters. You can find the video on my channel. I would also like to remind you that you can find the PDF plans in the description section of all my videos. Greetings from Turkey 👍
@@MuratGuney yes I have downloaded the pdf plans! Perfect! I'll have a look at your guide for longer cuts.
👍👍👍
Прекрасно, руки золотые, как все просто.
Большое спасибо. Рада что тебе понравилось. Напоминаю, что планы в формате PDF вы можете найти во всех моих видео в разделе описания. Привет из Турции 👍
Merci pour l'idée.
C'est vraiment génial. Quand on voit le prix des rails dans le commerce. Je m'y mets aujourd'hui.
Merci. C'est vraiment abordable et très utile. Grâce au plateau, vous n'avez pas besoin d'attacher quoi que ce soit à votre scie.
Unless you use the tracks for constructional lumber where looks aren't that important, skip the ø25 notches. Every time you reach a notch, you will get tear-out on the upper side.
The edge itself acts as both as an anti-splinter guard and a reference, just put the edge on the line.
Make sure your blade is square to the sole *before* plunge-cutting the runner and trimming the rail edge. ;)
And make sure your square is actually square when making the runner, as the saw blade needs to be 100% parallel to the guide rail to avoid pinching the blade.
I bought one of those small 85mm Worx saws some years back, and ran it against a guide edge. The blade was 't even fully int the workpiece when the blade started to pinch, and the blade warped. Turnex out that the sole was twisted a bit compared to the blade, so the blade entered at a slight angle. There were no way of adjusting it other than brute force, so I stopped using it and bought a 12V Bosch instead. The bosch doesn't cut as deep, but I have a proper circular saw for that (Bosch GKS 18V-Li including OEM tracks).
Everything you wrote is absolutely correct. It's like an instruction manual for a circular saw manual. Only 25mm notches don't splinter that much. Of course, you can say that if the knife is too old. However, since the sandpaper attached to the bottom also makes some height, even if there is no notch, the event you say may occur. But I didn't experience any discomfort. Thank you for your interest and I hope you continue to follow me.
Yes, that Bosch works for me to.
Excellent stuff for little money.
"And make sure your square is actually square when making the runner, as the saw blade needs to be 100% parallel to the guide rail to avoid pinching the blade." Did he not do that? How should it be done differently?
@@MuratGuney You also need to make sure that the disk in the raised state is in the same plane as in the lowered one.
This so far is the best version I have seen so far.. Thank you for sharing your idea and tips.
I thank you too. You can find PDF plans in all my videos in the description 👍
Absolutely genius
Thank you so much. I recommend you to check out my other videos as well. I hope you like it.
OK. Praca wykonana profesjonalnie.
Dziękuję bardzo. Możesz pobrać plany PDF z sekcji opisu.
Bel video, semplice, veloce ed economico 👍
Grazie molte. Sono felice che ti piaccia. Uno strumento davvero utile... continuate a seguirmi per favore
Very effective clrcular guide.
thank you so much. I'm glad you think so.
Just what i was looking for. Great design.
Thank you very much. I'm glad you liked it. You know that you can find PDF plans in the description section of all my videos. Greetings from Turkey 👍
Bizimle kibarca iletişime geçtiğiniz için teşekkür ederiz
Videonuzu ileride görmek için sabırsızlanıyorum, desteğiniz için teşekkür ederim.
Ben de teşekkür ederim 👍
Excelente Murat un trabajo bien realizado gracias por compartir tus conocimientos...el conocimiento es libertad..🎉
Gracias también. Me alegra que te guste. Ya sabes que puedes encontrar planos en PDF en la sección de descripción de todos mis vídeos...
Simpel and perfect!
Thank you so much 👍
Thank you for sharing 👀👀
your video is very good, I love it. 👍👍
Thank you too 👍 PDF plans in the description section
Çok güzel, tebrik ederim.
Possibly one of the best I have seen. Seems a lot of screws holding parts together - maybe they are necessary. Sight holes are a great idea - not sure if you would get tear out cutting across grain in plywood? Thanks for presenting this video. Cheers from Queensland Australia.
I thank you too. I overused the screws for stability and to prevent flexing. It is one of the tools that I use very efficiently.
@@MuratGuney your Project is miles away othsr users, who user 2 or 3 screws to fx.
Thanks for share
I thank you too. Greetings from Turkey 👍
I thank you too. Greetings from Turkey 👍
Brilliant idea and tutorial
Thank you so much. I am glad you like it. PDF plan is in the description section
Pekerjaan yang sangat bagus.. salam dari Indonesia
Terima kasih banyak. Aku senang kau menyukainya. Salam dari Turki 👍
Excelente trabajo muy creativo gracias
Gracias también. Me alegro que te haya gustado 👍
It's cool..! 👍👍👍
Grateeng from Indonesia...! 🙏🙏🙏
Thank you very much. I am glad you like it 👍
Самая лучшая идея 👍👍👍🙂
Большое спасибо 👍
Iyi bir fikir Murat. Not everyone has the space for a table saw. This would help many people. ; )
Thank you very much. This tool came in handy for many cuts, especially for long pieces.
Gran trabajo 👌
Gracias. Como sabéis, los planos en PDF están en el apartado de descripción...
Very good!
Thank you very much!
Thank you very much. I would like to remind you that you can find PDF plans in all my videos
Tebrik ediyorum, güzel proje, titiz çalışma.
Çok teşekkür ederim Ahmet bey
Exelente aporte gracias gracias
Gracias. Me alegro de que te guste. Puede encontrar las dimensiones en los proyectos en la sección de descripción.
Great design. Really like it a lot.
Thank you so much. I'm glad you like it. You can find the measurements in PDF format in the description section of the videos.
Gracias por compartir tu diseño
Gracias también 👍
Tebrikler. Beğendim
Many other things on your channel I could see all around the internet, even a few of them I made for myself but this guide so far never seen and it looks so useful and great, so most likely will copy them as I do not see atm any possible improvements to your projects so it will be just copied. Thank you, you got me as your new subscriber.
I thank you too. I just saw your comment because youtube posted it to the ones that need to be reviewed. Sorry for the late response.
@@MuratGuney it's no problem, not at all. Most likely you have settings that posts go there before posted but whatever , thank you and see ya again.
Bu alanda onlarca yabancı ve yerli videoları izlemiş birisi olarak, yaptığınız iş mükemmel ve takdire şayan. İnşallah kanalınız daha da büyür ve çok kimselere ulaşırsınız..
Çok teşekkür ederim Hasan bey. Doğrusu kendi vatandaşımdan gelen bu gibi mesajlar motivasyonumu daha çok artırıyor. Bütün videolarımda PDF planları bulabileceğinizi bildiğinizi düşünüyorum ama yine de hatırlatmak istedim. Hayırlı Ramazanlar
@@MuratGuney Kullanmış olduğunuz alüminyum profilleri almak istediğimizde nasıl temin edebiliriz? Belirli bir adı vs var mı acaba? İnternetten araştırdığımda karşıma birden fazla şekil model çıkıyor..
Kullandığım profil 5x25mm boyutlarında C profil olarak geçer. Ankara'da Kurtoğlu Alüminyum isimli firmadan aldım. İnternetten numarasını bulabilirsiniz. İsterseniz arayıp sorun. Başka bir izleyicimiz kargo ile gönderdiklerini söylemişti. Yaşadığınız yerde de sadece alüminyum satan mağazalarda bulunabilir.
@@MuratGuney Çok teşekkür ederim bu ayrıntılı ve yönlendirici cevabınız için.
@@hasansarac1595 Ben de teşekkür ederim Hasan bey. Kolay gelsin 👍
Ellerine sağlık kardeşim çok güzel kullanışlı bir aparat olmuş kanalında güzel projeler var hepsini fırsat buldukca izleyeceğim
Çok teşekkürler. Projelerimi beğenmenize sevindim. Takip etmekten vazgeçmeyin lütfen
@@MuratGuney Tabi ki emek verilerek yapılan işleri begenmemek olmaz kanalınızı takip edeceğim başarılı dilerim abone olup bildirimleri açıyorum kendinize iyi bakın görüşmek üzere sağlıcakla kalın selamlar
İyi dilekleriniz için tekrar teşekkür ederim. Size de sağlıklı günler dilerim.
Nice job well worth the watch
Thank you. Honestly, I shot the video when I was a novice. A really useful tool. I'm glad you like it
Very good.
Than you 👍
Качественно сделано ,хорошая идея
Большое спасибо. Я рада, что тебе нравится 👍
Incredibly Awesome, kind Sir!
Thank you so much 👍
@@MuratGuney ❤
Greetings from Turkey 👍
Simple and good
Thank you. I am glad you like it 👍
Eline sağlık güzel olmuş
Teşekkürler Yıldırım abim
Все гениальное просто
Спасибо 👍
Thanks, another excellent project! I live in a very humid climate - what are you using to seal the "end grain" of the MDF? You use a lot of it, so you have probably found a good solution. Thanks again for your videos
Hello. I thank you too. Honestly, where I live is pretty low humidity. However, I do not think that MDF plates will be damaged unless exposed to water for a long time. I do not prefer to use MDF boards in case of vertical screw throwing or in places that will carry loads. You must have seen in my videos, for example, if there is a piece in which I will see a nut, I use plywood or hornbeam. I have been using the products I have made for a long time and believe me, I have never had a miter break.
Спасибл за ролик, все очеь просто и красива.
Я тоже благодарю вас. Рада что тебе понравилось. Напоминаю, что планы в формате PDF вы можете найти в разделе описания всех видео 👍
Thanks you man👍
Thank you too 👍
excelente!!!
Muito obrigado. Saudações da Turquia
Пожалуй самый простой вариант из всех что видел Оригинальное решение без переделки самой пилы
Как ты говорил. Я не хотел добавлять в пилу какие-либо детали. Очень удобно пользоваться. Спасибо за интерес и комментарий.
Great idea
Thank you so much 👍
Работа, для распиловки размеров материалов, просто,клас. Ролик класный спасибо.
Большое спасибо. Вы знаете, что вы можете найти планы в формате PDF в разделе описания всех моих видео, верно?
СПАСИБО КЛАСС КЛАСС КЛАСС ПРОСТО ПОЛЕЗНО БЛАГОДАРЮ ЗА ВАШ ТРУД
Я тоже вам большое спасибо. 👍
Best one I have seen
Thank you so much 👍
Отлично. Я только не понял предназначение полукруглых отверстий по краю шины..
Привет. Во-первых, спасибо. Отверстия, которые я сделал в форме полукруга, были сделаны для того, чтобы было легче видеть размерную линию, проведенную на разрезаемом материале.
Really nice nand simple. Just wanat to ask what are the half curves along the track for? Thanks
Hi. Thank you so much. Half circles are made in order to easily see the dimension line on the piece to be cut. You may not, but it really works
ELİNE SAĞLIK ÇOK GÜZEL
Teşekkürler Muhammet bey
merci très bon travail , pourquoi ces trous de 25mn tout le long ? BONNE continuation
Bonjour. Tout d'abord, merci. Si je comprends bien, vous posez des questions sur les trous semi-circulaires. Ces trous sont réalisés pour voir facilement la ligne de mesure tracée sur la pièce à découper.
I did a very similar one but with just the laminate planks screwed together and no track or a sled. Seems to work well enough when I just keep pressure on the guide rail. Need to do some kind of rubberized underside too.
The sandpaper on the bottom works very well. There is no need to cover it completely... thank you for your interest.
@@MuratGuney Yeah I was thinking of grip tape with similar texture to sandpaper but sometimes I need to cut things like kitchen cabinet doors so I need something that wont scratch the surface.
You're right about that. Sanding can be harmful to coated covers. In this case, materials such as rubber are better.
Would it slide more easily if the boards were used upside down? Most laminate flooring has a texture to the display side and a very smooth underside. I am going to make a guide like yours so will try out using the boards upside down.
Hello. I think just do it the way I use it. The coating of the upper section is stronger and more slippery. You can test this by sliding two plates over each other.
Спасибо большое
Я тоже благодарю вас 👍
Excellent
Thank you so much. I'm glad you like it 👍
Muy buen video, claro y muy prolijo: Agradezco que lo compartas. Gracias
Gracias a ti también. Me alegro de que te guste. Puedes encontrar las medidas en la sección de descripción de todos mis videos. que tenga un lindo día
Hello
I looked at many similar projects, but I liked yours the most. There is something I don't understand. Why do you make 25mm holes where the disc moves? What is their purpose and will there be a problem if they are not there?
Hello. Firstly, thank you. 25mm holes were made to easily see the dimension line drawn on the part to be cut. even if it doesn't. but they work
This is the best DIY track saw. Brilliant idea to use laminate. One question though, how do you get it to slide so easily?
Firstly, thank you. I didn't do anything extra for it to slide easily. So I didn't take anything. Actually, that's why I used laminate flooring. So easy sliding. Thanks to the coating, it glides very well.
Отличный проект, ламинат очень скользкий , может не все виды но у меня дома точно такой😂, я несколько раз падал при резких движениях на чистом ламинате без коврового покрытия, автору успехов, это самый лучший что я нашел, также ламинат очень термо и влаго устойчив против температурного расширения или сжатия.
Nice idea
Thank you. It is quite useful. You can find the dimensions in the description section. have a nice day
@@MuratGuney hi
Bravo eline sağlık
Çok teşekkür ederim Abdullah bey. Beğenmenize sevindim
Yeni videomda bu klavuza uygun şarjlı daire testere yapıyorum. Umarım onu da izler ve beğenirsiniz. Hayırlı akşamlar
Bu kılavuzu parkeden yapma sebebiniz nedir hafiflik için mi MDF den olmazmı ayrıca kesim tarafındaki delikleri ne için açtınız teşekürler
@@abdullahkocabiyik7862 Parke yüzeyi lamine kaplı olduğu için çok güzel kayganlığı var. Ayrıca ekstra sağlamlık kattığını düşünüyorum Abdullah bey.
Yarım daire delikler kesilecek tahta üzerine konulan ölçü çizgileri olursa onları daha rahat görmeyi sağlıyor. Olmasa da olurdu ama emin olun yardımcı oluyor.