I think it has something to do with the magazine disconnect. He disconnected his, and I think it had to go on top, or it gets pushed up and blocks the trigger bar
Fixed it. I had to take out the magazine disconnector and bend it so it was straighter. After that, make sure the trigger bar is below it when you put it in. Without the magazine, the sear wont be able to be engaged, but with it it can and the hammer falls.
which parts did you polish and how was your result? so far i've shortened the mag safety and that took off about 1lb. i'm planning on polishing the hammer and sear connection and was wondering if anything else would be worthwhile. great video by the way!
9:05 I'm guessing in order to remove the Firing Pin Safety you have to use a punch and hammer to remove the rear sight base, which is why you didn't feel like removing it.
I don’t believe you can actually remove it it just has to be lifted up and placed in a different position. You may check ashburn armorers channel he does a lot of disassembly videos too
It's a bit easier to remove the locking block (and it is a locking block) by driving it's pin out first, then driving the pin holding the spring in. Just in my experience.
If you watch again it’s on the firing pin as I put it in the channel, then I remove the pin to show something and the spring stayed in the channel. You can see it as I put the firing pin back in for the last time.
![FN Five-seveN 5.7x28mm [HD] Cleaning & Features](http://i.ytimg.com/vi/ro8XlO9cXHc/mqdefault.jpg)
![FN Five-seveN 5.7x28mm [HD] Cleaning & Features](/img/tr.png)
Thank you for doing this. This doesn't look like a easy gun to take apart.
Why everytime i try to put my mag in it struggles and when i get it in the trigger stiffens up and cant pull it
I'm having the same problem. It works fine if I remove the magazine, but pushing it in, it becomes very stiff.
@@TruthsohelpmeYah its been months and i still don’t figure it out 🤦🏻♂️🤦🏻♂️ a new 5.7 just sitting there
I think it has something to do with the magazine disconnect. He disconnected his, and I think it had to go on top, or it gets pushed up and blocks the trigger bar
Fixed it. I had to take out the magazine disconnector and bend it so it was straighter. After that, make sure the trigger bar is below it when you put it in. Without the magazine, the sear wont be able to be engaged, but with it it can and the hammer falls.
@@archivaldosanchez7508 I figured it out. Do what I did and it works fine.
Thanks for teaching me how to disable the mag safety
Love my 5.7, but that mag disconnect is one of the more stupid things I've seen. Sounds like some liberal nonsense.
Wonderful Presentation !
That slide looks good with the normal sized barrel cover
I was looking to remove the rear sights but thanks anyway
Thanks for the video going to be doing a trigger job on my fn this coming week
which parts did you polish and how was your result? so far i've shortened the mag safety and that took off about 1lb. i'm planning on polishing the hammer and sear connection and was wondering if anything else would be worthwhile.
great video by the way!
Perfect video. Thanks
Where could I get another pin that locks the clip...
How did you disable your magazine disconnect? They are dumb
I wonder what the metal slide is coated with ? Phosphate or nitride?
9:05 I'm guessing in order to remove the Firing Pin Safety you have to use a punch and hammer to remove the rear sight base, which is why you didn't feel like removing it.
Yes correct
Do you have a video or can recommend a video on how to properly remove the magazine disconnect from the Mark II FsN?
I don’t believe you can actually remove it it just has to be lifted up and placed in a different position. You may check ashburn armorers channel he does a lot of disassembly videos too
How do you change recoil spring on 5.7 mk2
What about extractor? Ejector? Etc… this isn’t a full disassembly but close enough
The slide without the plastic is cute
It's a bit easier to remove the locking block (and it is a locking block) by driving it's pin out first, then driving the pin holding the spring in. Just in my experience.
Great video. Thanks.
My slide won’t come off the frame. This shits way harder to get off than my Glock 😭
skill issue
@45.00 minutes, did you say "pichoo" like you fired a gun? 😭
Need a new mag release clip
So many springs and pins in this gun man wth 🤣🤣
oh this is a cheap looking pistol for the price...
the price is because of the caliber.
@@meir6002 for how much the p90 go for, this is definitely expensive.
You reassembled your firing pin without the spring....
If you watch again it’s on the firing pin as I put it in the channel, then I remove the pin to show something and the spring stayed in the channel. You can see it as I put the firing pin back in for the last time.
What to doif hammer is stuck without clip in but is fine with clip