Hydrographics 101: An Easy Step-by-Step Guide on How to Apply Hydrographics
Вставка
- Опубліковано 20 вер 2018
- Hydrographics is the application of a pattern piece of art (film) onto an object in order to customize it, or change its character. Unless you are paying a premium, the “wood” or “carbon fiber” in your car is created by this process as is the camouflaged guns and ATVs you see out in the wild. This application method is decades old, and requires 5 basic ingredients: paint, hydrographic film, water, activator, and a protective clear coat.
In summary the part is first painted, (most hydrographic film is semi-transparent, and the base coat influences the overall finished look). The film is then floated on the surface of warm water for a minute or two in order to soften the PVA backing. The upper-facing surface of the film is then sprayed with a hydrographic activator, which turns the film into a liquid. The painted part is then slowly lowered into the film, and the paint chemically bonds to the liquid film, leaving the part “painted” in the design of the film.
Once “dipped”, the part is the gently rinsed in water to remove any excess PVA, and allowed to dry on a rack. Once fully dry, the part is then clear coated for UV and general wear and tear protection, but also to give an array of gloss levels, from wet-look gloss down to a matte clear.
Get all the supplies you need to turn your garage into a fully functional dip shop @ www.ohwpaint.com - Навчання та стиль
Best howto I've seen for this . No bullshit and strait to the point , good results too..awesome thx
Thanks Adam!
Hello! I have the same question of some other comments... How often should I change the water and how can I dispose of the non-usable water?
Nice Video Thank you
Great Video! Have question, I know you sanded the part before painting. What grit do you sand with, afterwards when you painted the controller is there no need to sand the painted controller before dipping. Thanks in advance🙂
we usually use a light gray Scotch Pad (extra fine) for scuffing. This provides enough 'key' for paint. Correct, no need to scuff before dipping. OHW has a long dip 'window'
@@OHWPaint 😊 Thank you
How do you dispose of both used waters? Can I put down my drain or backyard? and if so will it make the grass or sink the dip pattern?
hydrodipped grass sounds pretty cool ngl
2k clear coat used or 1k?
I got question . If i open a shop ,
How often should i change the water?
Is it really necessary to paint the part before dipping ??
What paint to use on !!!
Glossy or matte !!!
And about raising, why does the water look like its a soapy water ...
Please answer all my questions please ...
Hi LWL - we recommend One Hit Wonder base paint (yes you need to paint the part so the film has something to adhere to). The gloss level depends on personal preference and is determined by the clear coat. The water is not soapy it is most likely the PVA from the film/activator reaction. You do can clean the water of film residue with a fishnet from an aquarium store. Hope that helps.
Do I need to paint the shell if my controller is white already and I want it white under the hydro film?
Hi Josh - great question. You will need to paint the controller as the film needs to "stick" to the paint and will not adhere direct to the substrate. Hope that helps!
Why did you make look so easy? Whats the correct method for dipping at the 30* angle. As in, which part should be dipped in first for proper coverage
Hi there -- Send a picture of the item you are dipping to info@ohwpaint.com and we can better help.
How can I re-do it with my controller if I messed up? One part of the controller didn't stich with the carbon fiber film
simply rinse and dry. If there are any "globs" of film, sand smooth with warm soapy water. then dry, and paint directly over. No need to strip the part. paint right over the film.
What color spray paint do you guys recommend to receive a real carbon fiber look?
We like Metallic Graphite with our classic Black and Clear Carbon Fiber film.
started my first dip it turned out good but the item itself feels slightly sticky after overnight dry, what are we doing wrong?
Hi, it sounds like you may not have rinsed the dip properly - sometimes this can take up to 5 minutes. Please contact JJ via text at 305-318-1468 it you still have issues
How long do I have to wait to rinse and does it have to be cold or warm water
you can rinse immediately, and as long as it's not hotter than 100 degrees, and temp is fine. The closer to 80, the better/ faster
Whats an activator can?
Hi, how much time should i wait between final base coat and dipping?
You want to wait 5-10 minutes until the paint is dry to the touch
He doesn't seem to be a good conversationalist
Clearcoat brand suggestions. Paint wearing off after hours of play. I need a harder clear.
The paint or dip should not be wearing off with any 2K automotive clear (a standard clear is more decorative and is not intended for things that will be handled)- feel free to contact us at info@ohwpaint.com so we can better help troubleshoot with you.
Would I need to remove the original paint before preparing the new one?
As long as the existing paint is in good condition and adhered to the part properly, you can just degrease, scuff, and paint OHW over the top
@@OHWPaint Much obliged!
For ps4 controllers, do i need to use sandpaper for them or what type of degreaser should i be using for it?
We like Prep All degreaser. You don't need sandpaper, just a light gray scotch pad. Hope that helps!
@@OHWPaint that truly did help alot i do appreciate you for that info so much, one more question, where can i buy the gray scotch paper from?
@@OHWPaint i meant pad lol
@@Sheldric09 an autobody supply shop or check amazon or walmart
@@OHWPaint thank you 💯💯💯
thx, Great video
but the music is stressing !!
We can't disagree with you there. Royalty free music...lol
@@OHWPaint haha been there, i finally customized my N3ds on my channel, thx again
Shake can vigorously for 2 minutes, then apply a light coat? I followed the directions, I don't know how people do this and get it correct? I put on the lightest coat I have, even though I'm burning up hot, I don't know what this has to do with dipping my controller
Edit: to put the clear spray ihave to get out my medium coat? FML
is clear coat a must? what if I want a mat finish?
Hi, yes you need clearcoat to protect the film. Otherwise the ink will get scratched. For matte, we do sell a standard matte clear and a 2K matte clear that you can apply directly over the dip once dried
I have another question, so im trying to hydrodip my ps5 panels, what step should i do first?
You need to clean (we like the degreaser Prep All) and scuff with a gray scotch pad.
@@OHWPaint all good then what do i do next after i use those two items
@@Sheldric09 Please follow the video or find step by step directions here www.ohwpaint.com/blogs/news/how-to-apply-hydrographics
@@OHWPaint thank you i most definitely will
Can I dip objects made out of modeling foam?
Can you please send a photo to info@ohwpaint.com
How much would you charge if I had you do that to my firearms Slide and Trigger?
Hi Ehsan, We sell paint and hydrographic supplies. We do not provide hydrodipping services. But if you email us your info we can see if we know anyone in your area who can help. info@ohwpaint.com
How long does it last?
if you use our 2k clear, indefinitely. As long as any car finish, if taken care of. The kit comes with a 2K Clear option and you can also find our 2K Clear here:www.ohwpaint.com/collections/clear-coats/products/2k-clear-coat
So we have renamed decals, a nice new twist, but still a decal. Thanks, n nice work.
that’s 1 way how to make a short presses long 😅
What is this god awful music
Why did you spray something onto it before doing anything else, is that paint, dose it make it stick better? Dose it make it last longer? Dose it make it feel better?
That's an activator spray.
Going to call you Monday. Daniel gave me your number. I need to get setup for hydro dipping in my shop
Sounds good!