Had a mktor that opened and the completely refused to close.. I have a gate that weights close to a ton. Can't move it front or back.. lifting the gate with great difficulty changed that. You saved me while drunk at 11pm. And saved me 350$
After I did the tutorial is it not supposed to give me a limit set successfully or failed message. Now it's show no limit set and doesn't want to operate automatically.
Have a serious problem. I have followed your setup video to the letter four times, however when finished I have a gap of some seven and a half centimeter's in the closed position.
Good morning, thank you for the opportunity to be in your show, however i did follow all the steps but still the gate is not opening or closing with remote, please advise. The window shows back to square1
Thank you for the video but I am confused as you don't mention about having to manually move the gate to half way through it's travel before you start this process?
Hi Andy. Thanks for the feedback. Whilst the video concentrates on the electronic procedure of setting the limits, your point is well received and it may have been well worth mentioning that. I have since added it into the description of the video to read "Before proceeding please ensure that gate stops are securely installed and the gate is positioned half way between opened and closed.".
Can you set up the end-stops 1 and 2 manually? I.e. I will just pull the gate manually, stop and tell its computer to record this location as an end-stop. Then I do the same for second stop.
Hi, Please help When setting up a new D5 EVO limits, the gate goes slowly to the open position, the wizard says it is finding the first stop, then simply stops. It will not reverse to find the next limit and then the message on screen changes to Centurion systems, D5 evo waiting for Co-processor. then it says WAIT 1 MINUTE OR RESET ALL POWER and the screen goes blank and returns to the setup wizard
Does an electrical current pass through the end stop to the motor or something? I blocked the end stop with a rock so the gate doesn't open too much and now it's failing this process
I have centurion G5 Gatemotor not even a year I have this motor it have been giving me problems same time's it doesn't open now it take out the remote control it self I did try to add the remote again but nothing can some customer service help me please I did buy this motor course my nephew told me this is good company
What do I do when it does this and gives me an orgin not found error than doesn't verify the 2 stop ends . This is from a gate motor that was working perfectly
Can anyone on here help please. I have done this multiple times and it always worked, but now for the first time it fails to recognize the second(left hand) stop. The origin marker is working and cliks when moving past
Good morning have a problem with my motor it keeps on saying battery low although I checked that it has 3 out of 4 bars I was trying to set limits it only opens and completely shuts down and restarts again so then I wanted to continue my settings and now doesn't even close always shuts down
Hi Lucas. Please give our technical support team a call on 011 699 2400, or send an email to support@centsys.com. One of our skilled technicians will assist you with your query.
My hek sê "no limits set". As ek dit doen, dan kry die hek die eerste "stop" maar nie die tweede een nie- hy hou net aan hardloop? Ek moet eers "emergency sto[| druk. Hek wil niks oop gaan nie.
My gate is running to the close position during thos prosegure and then stop, then screen goes blank and reset, doesnt go back to the other end stopper, what may be the problem ?
Hi there.my gate started moving slowly and ended up closing and opening on its own.I went thought setup.close and opens then says setup failed no origin found.help please
It's looking for your origin marker (the magnet on your gate rack). Perhaps something's happened to move/dislodge it. Please call our Technical Support Call Center for further assistance on 011 699 2481.
HI there, I discovered it my was battery that was at fault. I have replaced the battery and the limit settings seemed to work. But now, after setting the limits (according to the instructions here) the gate closes halfway and then automatically opens again immediately!
Hi Elias. Thanks for your query. Please give our technical helpline a call on +27 11 699 2481 or drop an email to support@centsys.co.za. Our friendly and knowledgeable technicians will be able to assist you.
+Edwin Kalimadola Hi Edwin The error indication signifies that the sensor is not receiving a valid pulse from the gate-mounted origin magnet, or the controller is not receiving a signal from the sensor. Possible causes could be: •• The distance is too great between the origin sensor and the magnet •• The magnet and sensor are mounted at different levels •• Incorrect orientation of magnet •• The gate is getting stuck at a certain point before the magnet has passed the sensor •• Faulty origin sensor Solutions to rectify this include: Check the information screen on page 65 - it should display the position of the magnet (left/right) when the magnet is passing the sensor •• Ensure that the magnet and sensor are mounted at the same level •• Ensure that there is an audible ‘click’ whenever the magnet passes the origin sensor •• Ensure that the arrow on the magnet is facing the operator - there should be a repelling action when the magnet is brought near the sensor ••Move the magnet closer to the origin sensor. •• Replace the origin sensor If you need any further assistance please feel free to call our Technical Support Call Centre on +27 (0)11 699 2481
Hi, Please help When setting up a new D5 EVO limits, the gate goes slowly to the open position, the wizard says it is finding the first stop, then simply stops. It will not reverse to find the next limit and then the message on screen changes to Centurion systems, D5 evo waiting for Co-processor. then it says WAIT 1 MINUTE OR RESET ALL POWER and the screen goes blank and returns to the setup wizard
Amazing video,I followed your steps to the end and it worked!!
Thank you
Thanks for the excellent tutorial.just one piece of advice to all.ensure the gate is "locked" or engaged on the track.
nic osia Good observation. 100% correct - that is a requirement prior to this step :-)
My show no limit set
@@drekayode3799 Did you then scroll through the menu to set up the limits?
Setup fail no origin found wat you do then please
Had a mktor that opened and the completely refused to close.. I have a gate that weights close to a ton. Can't move it front or back.. lifting the gate with great difficulty changed that. You saved me while drunk at 11pm. And saved me 350$
Thanks. 🤣
Heyyyayyyy your gate is on fiaarrrrre..... thanks for the walk through.
Worked well Bro thank you so much
After I did the tutorial is it not supposed to give me a limit set successfully or failed message. Now it's show no limit set and doesn't want to operate automatically.
What to do if the gate can’t find limit stop 2
what was your fix?
Have a serious problem. I have followed your setup video to the letter four times, however when finished I have a gap of some seven and a half centimeter's in the closed position.
What to do if screen shows no limit set?
Then this is the video to follow, for that problem
Good morning, thank you for the opportunity to be in your show, however i did follow all the steps but still the gate is not opening or closing with remote, please advise. The window shows back to square1
What if it's not picking up the end stop limits after following this procedure?
Thank you for the video but I am confused as you don't mention about having to manually move the gate to half way through it's travel before you start this process?
Hi Andy. Thanks for the feedback. Whilst the video concentrates on the electronic procedure of setting the limits, your point is well received and it may have been well worth mentioning that. I have since added it into the description of the video to read "Before proceeding please ensure that gate stops are securely installed and the gate is positioned half way between opened and closed.".
@@CenturionSystems doesn't need to be.. you can turbo the open and close with the round button. :)
so how do I setup the end stops then? rather misleading title
Can you set up the end-stops 1 and 2 manually? I.e. I will just pull the gate manually, stop and tell its computer to record this location as an end-stop. Then I do the same for second stop.
Hi my motor just say no limit set what must i do can you pls help me
Hi, Please help
When setting up a new D5 EVO limits, the gate goes slowly to the open position, the wizard says it is finding the first stop, then simply stops. It will not reverse to find the next limit and then the message on screen changes to Centurion systems, D5 evo waiting for Co-processor. then it says WAIT 1 MINUTE OR RESET ALL POWER and the screen goes blank and returns to the setup wizard
Have you found out what the problem is i am having the same problem
@@eugenekleu3629 have you figured out what the problem could be? Im having tbe same issue
Very helpful. Thanks a lot
My gate won't move after pressing " clear gate area " how can I resolve this ?
Awesome sauce! Lekker stuff.
Hi, what will happen if the Spade connector on the left, by the GND symbol is not connected?
my d5 keeps saying no origin found when i try this. what can i do
I have the same problem. How did you resolve this matter? Thanks.
Same here, did u win?
Check if your magnet is responding when passing by the motor,if it does not produce a clicking sound it shows its not positioned well...
I did that and when actually supposed to start the motor run a bit but the gate doesn’t work
Gate closing n opening very slowly. Why
Hey did you win on this problem?
I've had my D5 Evo since August 2017 - when do I need to change or top up the oil, how much do I add and what type of oil do I use?
Did you get an answer yet?
Does an electrical current pass through the end stop to the motor or something? I blocked the end stop with a rock so the gate doesn't open too much and now it's failing this process
Mine turns off when I try and run the motor. Not sure what to do
What do you do if you set the gate limits or run the wizard and then when it starts to run it reboots and stops?
Is it possible to shorten the opening distance by around 10cm without going through the setup wizard again?
How about it asks the endstop
I get an error "colission detected" after the second cycle. I moved the magnetic stop recently and have to set new limits.
My gate motor says "setup fai
no endstops
no origin found
Did you find a fix? Please help?
Olá, olhe eu tenho problemas com o motor do meu portão de marca D5 Evo, esta a resistir o seguinte erro;Motor Fault Disconected
My motor just says waiting for coprocessor after these steps then it restart..its not working what could be the issue
Hii how do you put this motor on override manual so I push it . Iv span the wheel clockwise to try release it but it’s not working
hi there my d5 evo pc board does not give me the dianostic setup like the battery charge and the battery picture why is that
we are not seeing the screen well
ok i would like my gate to close at 10pm on week days and open at 6am is this possible.
Cant find second stop
How much is the D5 Evo electronic remote pack without the tracks and motor or swing arms as in hinged gate design?
When I'm pressing the last option the motor doesn't go it just move 2 sec and come back can you pls explain to fix it
Hi our gate motor says gate stalled on control panel, how do I fix it
Hello sir. Mine is saying Max Collision. How do I solve this problem?
Hello
I have message no limit on the screen, so my 4 remotes are not working, so can you give me advice what can I do
No way that your motor screan can be writes in block letters to makes us cleare vision when you demonstrate.
Mine also does not find the second end stop?
Sorry I am having trouble connecting a gate light how do I do it. Everything else is working well.
The red wire goes into AUX (to the left of Status) and the black wire goes into COM (to the right of Status)
Thnks alot I managed to clear the fault code
Can you show me how to program a new remote? I have a D5 Evo
I have centurion G5 Gatemotor not even a year I have this motor it have been giving me problems same time's it doesn't open now it take out the remote control it self I did try to add the remote again but nothing can some customer service help me please I did buy this motor course my nephew told me this is good company
If the gate goes forward and the system shut down
What do I do when it does this and gives me an orgin not found error than doesn't verify the 2 stop ends . This is from a gate motor that was working perfectly
I have set the limits before with no hassles
@@MeeganGounder did you find a fix?
Can anyone on here help please. I have done this multiple times and it always worked, but now for the first time it fails to recognize the second(left hand) stop. The origin marker is working and cliks when moving past
I have the same problem aswell, have you managed to find the solution?
Good morning have a problem with my motor it keeps on saying battery low although I checked that it has 3 out of 4 bars I was trying to set limits it only opens and completely shuts down and restarts again so then I wanted to continue my settings and now doesn't even close always shuts down
Hi Lucas. Please give our technical support team a call on 011 699 2400, or send an email to support@centsys.com. One of our skilled technicians will assist you with your query.
Thanks I'll do it.
My hek sê "no limits set". As ek dit doen, dan kry die hek die eerste "stop" maar nie die tweede een nie- hy hou net aan hardloop? Ek moet eers "emergency sto[| druk. Hek wil niks oop gaan nie.
My gate is running to the close position during thos prosegure and then stop, then screen goes blank and reset, doesnt go back to the other end stopper, what may be the problem ?
The battery termanal was corroded, replased the battery and problem solfed, thanks
What do you do if it shows fax
Hi there.my gate started moving slowly and ended up closing and opening on its own.I went thought setup.close and opens then says setup failed no origin found.help please
It's looking for your origin marker (the magnet on your gate rack). Perhaps something's happened to move/dislodge it. Please call our Technical Support Call Center for further assistance on 011 699 2481.
HI there, I discovered it my was battery that was at fault. I have replaced the battery and the limit settings seemed to work. But now, after setting the limits (according to the instructions here) the gate closes halfway and then automatically opens again immediately!
I've tried everything from resetting the limits to resetting the system. After the limits are successfully set, the gate opens halfway then closes.
Give the chaps at Tech Support a call on 011 699 2481. There are a number of troubleshooting items they can run through with you.
Mine too
Matt Hains Mine too. and the installation manual seems to be written by an idiot that did not realize us non techies will need clear instructions
I set limits finding end stops 1 & 2 successfully but the gate stalled not running to normal what could be a problem?
You save me and my gang R1000 and stress 😂😂😂
When my motor does the first move it reaches the first stop and then the board resets. What could be the problem and is there an easy solution?
Hey Brandon, have you recieved feedback regarding this issue?
Hi.Did you manage to resolve the problem?
Did you get an answer? I have the same problem
sorry. I need one help my centurion evo d5 isn't run well the error information is. motor fault disconnected please help me.
Hi Elias. Thanks for your query. Please give our technical helpline a call on +27 11 699 2481 or drop an email to support@centsys.co.za. Our friendly and knowledgeable technicians will be able to assist you.
I do the setup but is not changing saying no org found
+Edwin Kalimadola Hi Edwin
The error indication signifies that the sensor is not receiving a valid pulse from the gate-mounted origin magnet, or the controller is not receiving a signal from the sensor. Possible causes could be:
•• The distance is too great between the origin sensor and the magnet
•• The magnet and sensor are mounted at different levels
•• Incorrect orientation of magnet
•• The gate is getting stuck at a certain point before the magnet has passed the sensor
•• Faulty origin sensor
Solutions to rectify this include:
Check the information screen on page 65 - it should display the position of the magnet (left/right) when the magnet is passing the sensor
•• Ensure that the magnet and sensor are mounted at the same level
•• Ensure that there is an audible ‘click’ whenever the magnet passes the origin sensor
•• Ensure that the arrow on the magnet is facing the operator - there should be a repelling action when the magnet is brought near the sensor
••Move the magnet closer to the origin sensor.
•• Replace the origin sensor
If you need any further assistance please feel free to call our Technical Support Call Centre on +27 (0)11 699 2481
I did this but my gate says no limits set what's the problem?
Same. Did you find out how to fix it?
Same here still doesn’t work. Any idea guys?
Mine too
Can’t see the screen
What do you do if the 20c LCD stops working?
How do I cancel some of my remotes and renumber the new ones
You do not give all the information on this video? This is not a useful video.
Doesn't work
No limit set
Tradução em português
Goggles tradutor para português
Vh8
Worked well Bro thank you so much
Hi, Please help
When setting up a new D5 EVO limits, the gate goes slowly to the open position, the wizard says it is finding the first stop, then simply stops. It will not reverse to find the next limit and then the message on screen changes to Centurion systems, D5 evo waiting for Co-processor. then it says WAIT 1 MINUTE OR RESET ALL POWER and the screen goes blank and returns to the setup wizard
Mine does the same thing
Please assist, mine once i'm done with all the settings, when i'm supposed to hear the motor moving, it switches off
Hi. I'm currently facing the same problem. Were you able to fix it?
am try to set centurion d10 by using pressing button at the security post is not working please can you teach me
What can i do if motor say no limits set