Відео

1200 cc on 883 cc heads ? is that sucking through a straw ? - doing the head teardown - pocket port a little clean polish valves ? seems backwards to me ? - s pent $3,5oo on the block - and $7,000 on the heads ! - 8,200 rpm brian crower components !

Update?

picked up one a few month ago also needing tlc @ 44k miles. they are good bikes

I'm about to cave too, it's between this one and the Bauer 8" so I'm looking forward to your video that I just started watching!

Ive been modeling my 93 build after yours, but i am stuck on the ignition switch. I have the same one you used, do you know what wires you ran to the back of the new switch?

Man, I could talk to you for a minute. Those buttons are trash and the angle of the housing, like you mentioned, doesn’t work out when you install the switche. And the owner will just talk shit to you.

Prism supply has a small brake reservoir and lever

Super helpful. Currently doing cams and high compression top end rebuild and researching ignition mods on my 91. 🤘 2000-i it is in my case.

bolts are upside down.. 🤔

I have a 1998 fatboy with an evo second gen . So all you need it’s that unit and the coil , you just disconnect the oem module under the seat ? Do you have to bypass any of the original wiring from the Oem module . “Not the ignition pick up down in the engine that gets discarded .

I wish you would have shown the alternator cable swap a bit more. I have a rubber grommet that the cable runs through and its connected to some sort of clip that the ac lines run through. For the life of me I cant find where the clip is to remove these.

Change the oil ? Thought you just rebuilt the engine...

Very good video and visual instruction.

Can you make these into a variable speed?

Thanks for the video and bacon on!

This is definitely not a how-to video. This is a watch me do it video

When you tightened your axel nut back on was it pulling the axel out of the diff making it unsealed ?

Still holding up good?

I bought the Battery post clamp in Swan River Manitoba for $ 11.00 Canadian. Add wire and an end connector for $ 2.00 . Really good price compared to new OEM Cables.

Will this work for an 05

I’m building a wider platform for ATV’s.. need to extend the petals so they come out further.. has anyone done it and if so how or where did you get the extensions?

Picked up a NIB one at a garage sale for $30! Still haven't set it up, but have 3-4 projects backing up...

Something is wrong with your editing. I kept hearing music in the background.

Thank you very helpful video, but instead ov the 14mm I found that a universal box end wrench works best

Do you know if it matters to use copper core plug wires? Got a kit with suppressor wires and I'm hesitant to put them on.

It’s the heat from the exhaust pipe that roasts the electrical on the motor. For better results, put some exhaust wrap for a couple feet around the exhaust on the area that is close to the TC motor. You’re welcome 👍

Hi, thanks for the video. Did you manage to find a sleeker brake reservoir and lever?

Thank you,great video❤

What are the chrome pieces called on the side of your doors trying to get some for my truck

"Um" ? From Umbridge? 😅

Do you know the size of the cap wrench you used for the hydraulic filter?

Thanks for this man, I'm building a 93 Sporty and it seems we have very similar ideas, so it's great to see someone doing what I need to see. Thank you.

I just bought a 738 new with auto coupler. Mower rattles and makes noises. I think it's the part that holds the coupler in place. Does your mower deck rattle?

what brand wheel hub bearing assembly did you use and how have they been working for you??? Any issues?

Appreciate the video! I am doing a similar job and got a set without helper springs so this answered my question on swapping them over.

Once that obnoxious music started I was done. See ya!

The music change from teardown to rebuild is great 😂 😊

I got one of these, does pretty well but too easily stops if you use too much pressure.

What is that bar you had to take off

Nice

Sweet lookin truck. I don't like red paint on trucks but this looks good. A good darker shade of red.. 💪😎

jost found the video, good review. by the way, that bobber looks awesome.

I'm 400 miles away from home pulling a 20ft trailer with 4 atvs on it and my truck just started doing this. Thanks for the info

Hi! I want instal this Dynatec 2000i on my Evo 1987 and I have 5 Ohms Dyna Coil. Can I Connect it with this Coil ?? Thank You

I have the same control arms on mine. 😎

How long was your replacement bolts for the foot peg my bike came with new forward controls but the holes on the primary are empty and I need the bolts

Which way should I turn wrench to put back in two wheel drive?

was doing this today and got to about the positive starter cable? is it a 15mm? it’s suck a damn pain and i don’t wanna round it off

Going to do this to my 2012, but i am going to coat with raptor liner, front and back.

PS: you DO know that you can purchase new keystone bars that are internal wiring ready for like $80 bucks right? That way you won't sheer off the casings and ground out your wires after fishing them through a drill hole. But hey whatta I know, only been working on hogs for 31yrs