![drevilatwork](/img/default-banner.jpg)
- 47
- 273 874
drevilatwork
Приєднався 1 вер 2007
temporary diy coolant pressure sensor using tireminder tpms sensor to diagnose coolant system issues
diy coolant pressure sensor using tireminder tpms sensor. While it was working it showed pressure being anywhere from 3 psi to about 11 psi when the engine was really hot while going up a mountain. It did work for about 3 weeks after which the sensor just stopped transmitting. My guess is that the heat under the hood was too high for the sensor. I Will try it again but placing the sensor somewhere less hot and running a hose from the top of the tank cap to the new sensor location. Still a good temporary setup to diagnose coolant system issues...
Переглядів: 136
Відео
view bench on the edge of the cliff in Twin Falls idaho
Переглядів 214 місяці тому
view bench on the edge of the cliff in Twin Falls idaho
look inside a battery disconnect switch for semi trucks
Переглядів 1514 місяці тому
took apart a battery disconnect switch from a volvo vnl semi truck with d13 engine. it had a hairline crack on the housing so i wanted to make sure it wasn't corroded inside which it wasn't. i did clean up the contacts with a wire brush before i put it back together. i also put UV resin over the crack to seal it
how Volvo makes or glues wire splits on a D13 VNL original OEM Harness
Переглядів 3574 місяці тому
was curious how volvo makes thin wire splits on their harnesses so i took a new one apart. there is no split connector. they r not even soldered. the split off wire is GLUED to an exposed uninsulated part of the main wire. anyone has any idea what glue they used?
Burn Buddy heated insoles levels voltages
Переглядів 104 місяці тому
video shows how the burn buddy heated insoles control the heat output - by applying different voltages
Biolite 200 VS Petzl Bindi 200 ultralight headlamp comparison
Переглядів 686 місяців тому
an interesting comparison between the Petzel Bindi 200 and the Biolite 200 headlamp . this might also apply to biolite 325 as its very similar to the 200. in short, the head units have almost the same weight and battery size but the Petzel has a much lighter and smaller headband. on the other hand the Biolite has fully variable light intensity for both the white and red beams and all the modes ...
Biolite 200 headlamp runs while being charged
Переглядів 26 місяців тому
this video shows the behavior of the Biolite 200 headlamp when it gets plugged in to charge while it's being used. The headlamp runs almost the same while plugged in to charge . the only difference is if u have the it on maximum brightness and u plug it in, the intensity will drop some. Headlamp charges at 0.32 Amps
how to remove Volvo VNL semi truck mirror
Переглядів 496 місяців тому
how to remove Volvo VNL semi truck mirror
swisstech lies on stahlern knife packaging knife is NOT FULL TANG
Переглядів 3,4 тис.9 місяців тому
i took apart a swisstech stahlern fixed blade knife i got from waly to find out that swisstech lied on the packaging about it being full tang
how to test starter on a volvo vnl d13
Переглядів 10 тис.Рік тому
how to test starter on a volvo vnl d13
on d13 volvo vnl semi truck the alternator main positive wire goes first to the starter
Переглядів 3,4 тис.Рік тому
for whatever strange reason, the alteranator positive wire goes to the starter where it connects to the big positive wire. this is a strange / idiotic design choice considering that, from the alternator, it takes cosiderably more cable to get to the starter than to get to the batteries. on top of that, the alternator cable goes behind the ecu , then behind the air compressor, then over the tran...
DIY bumper corner for volvo VNL semi truck
Переглядів 168Рік тому
an idea on how to make a bumper corner for a volvo semi truck instead of paying 500$ at the dealer everytime a rabbit jumps in front of your truck
Ridgid Battery direct charging by providing + to T2 terminal
Переглядів 1,9 тис.Рік тому
Ridgid Battery direct charging by providing to T2 terminal
Load testing the smalles amazon stick welder GZ GUOZHI 130A
Переглядів 1,9 тис.Рік тому
i am using 12v cartridge heaters rated for 80w at 12v. they can take higher voltages and amps fir shorter periods of time. got 4 of them in paralel connected to welder output.
smallest amazon welder GUOZHI arc-130 vs Harbor Freight smallest 80 amp welder size and weight
Переглядів 1,2 тис.Рік тому
comparing the size and weight of the smallest harbor freight 80 amp welder to the smallest amazon welder the GUOZHI arc-130 which not only is supposed to make 130 amps vs the 80 of the harbor freight one , while being much smaller and lighter , but it also comes with auto darkening glasses and is considerably cheaper
volvo VNL cold hot air actuator mechanism and valve
Переглядів 15 тис.Рік тому
volvo VNL cold hot air actuator mechanism and valve
volvo vnl semi truck outside to inside air switch actuator
Переглядів 470Рік тому
volvo vnl semi truck outside to inside air switch actuator
testing automotive relay turn on and turn off voltages
Переглядів 78Рік тому
testing automotive relay turn on and turn off voltages
testing volvo D13 fan control solenoid resistance and replacing it with Freightliner solenoid
Переглядів 9 тис.Рік тому
testing volvo D13 fan control solenoid resistance and replacing it with Freightliner solenoid
volvo d13 fan control solenoid power consumption is 0.27Amps
Переглядів 1,7 тис.Рік тому
volvo d13 fan control solenoid power consumption is 0.27Amps
volvo d13 BAD fan control solenoid fuse location
Переглядів 21 тис.Рік тому
volvo d13 BAD fan control solenoid fuse location
better way to add an engine fan switch to a volvo D13
Переглядів 5 тис.Рік тому
better way to add an engine fan switch to a volvo D13
WEIZE 18Ah Lifepo4 battery take apart disassembly
Переглядів 1,4 тис.2 роки тому
WEIZE 18Ah Lifepo4 battery take apart disassembly
ISDT Q8 max charger 5A max limit DC output power supply
Переглядів 8212 роки тому
ISDT Q8 max charger 5A max limit DC output power supply
When generator head is mismatched with engine and load
Переглядів 2633 роки тому
When generator head is mismatched with engine and load
If u look at the next point under wat you were looking at it's an accent piece at the end of the tang
Ahaahhaaaaahahahaaaaaaha ha ha fucking ha!
Oh brother, you have no clue do you?
That is splitting hairs . I call BS
Sure looked like a full tang! Good knives for the money
Full tang. No lie. You're wasting your breath ... Doctor Evil. Swiss Tech stuff is pretty decent all around.
It is full tang. That red piece is just an end cap for color and flare.
Well you proved it sir! You are indeed, an idiot, and that is a full tang knife! Gratz!
Just stop if you don't know a lot about knives do your research to make a video and look like this
Really?
So it can be anodized aluminum
It’s full tang.That piece is for a lanyard.I own this knife.Its solid.Ive thrown it in my board quite a bit.The screws are lock tight.
Very nice knife do you talk to your mom like this?
I have the guozhi 210 amp and its a beast for the price
Full tang in my book , I believe the end is shaped that way to aid in the manufacturing process.
I’m in awe that this man even made this video
$10 engine wash and yours looks like this?
My fear of coroded harnesses and blown orings is greater than my love for clean engines. Regular rain will penetrate the top trailer marking lights regularly. Imagine what a pressure washer can do... then imagine how many parts u end up changin before u or your mechanic figure out its the harness...
While it was working it showed pressure being anywhere from 3 psi to about 11 psi when the engine was really hot while going up a mountain. It did work for about 3 weeks after which the sensor just stopped transmitting. My guess is that the heat under the hood was too high for the sensor. I Will try it again but placing the sensor somewhere less hot and running a hose from the top of the tank cap to the new sensor location. Still a good temporary setup to diagnose coolant system issues...
Does this actually work??
Costumer is always right. the costumer:
Bro, seriously? It’s full tang, it does not compromise the integrity to the knife.
Dont make knife videos please. I just got dummer watching this......
There is an easier way. Pin 19 on Ecu under the fuse box in dash. Its that wire and you only need a switch to ground
That is correct, i can confirm that cause the truck i have now has an viscous fan clutch and that one is controlled by the ecu so there is no air going to it. I did wire a switch to that pin and it works...
That is a full tang knife with the addition of an aluminum lanyard attachment built into the handle
Thanks bruh
Holy shit. You’re gonna be this picky? 😅
its full tang its just a lanyard hole
Fue útil gracias
I used it for about 10 days last winter and was surprised how well they worked. The voltage drop is intentional... that's how the box controlls the heating level of the insoles. Very well worth the money if u have to spend a lot of time outside even the most insulated boots will eventually get your feet cold eventually plus you can't adjust how hot or cold your boots get , but you can with these
This is a serious voltage drop but what can you expect for this price? I'd put a quality power bank and not think about it twice. Apart from this - how is the quality of the insoles - materials, flex, comfort, stiching, cabling?
I've got that same gz gouhzi arc130, and it's pretty amazing for the size. Does good with 3/32" rod. I've used 6011, 6013, and 7018 with it, no issues.
I feel like you're being too critical of a low budget knife. It's full tang my dude.
Whatever it is, it's made in china!!! Dont buy junk.
Tai ne "glued" tai vadinama indukcininis virinimas, kai laidai tarpusavyje suvirinami/sulydomi! amžina jungtis gaunasi
Ok since you just want to complain and I have already posted on here before that this thing is a beast, why don't you post a video of you putting it to use huh? Prove yourself instead of complaining about absolute nonsense. Show us how this knife is evidently a joke and a "cute toy" as you so ignorantly called it. I know you won't but go ahead prove us wrong.
Delete your channel
Its a full tang enough said.
Great educational video,, thank you so much
Brah that full tang and you’re playing semantics. STFU
unreal response 😂
Shut up! Its full tang! The add on piece is for a lanyard. Go away!
I looked for those chargers. I cannot find one that does an 8Cell battery pack, they all do 1-6 cell.
Thanks I was able to get my batteries charging.
It's not a lie if the tang goes always through ur hand dummy, and the aluminum piece is to take weight off the knife handle cause it's already handle heavy
Dude, think before you speak. Turns out this $40 knife is INSANELY tough. As good or better than most Benchmade knives I've used. That extra bit there makes no difference. It's full tang.
Person who deinstall Volvo started should get professional mechanic certificate from Volvo.
..that dosen't go up , it goes back in to the engine , it also have an arrow pointing down for the flow of coolant (outlet coolant core valve) . .. good vid anyway . 👌
You don’t know much about knives construction I see.
Tell me you don't know what full tang is without telling me
now that i see it off and what the tang looks like, maybe i'll just go ahead and void the warranty on mine so get rid of that piece of aluminium and round off the back