Відео

Commutation brother not H bridge.

Sorry not buying anything you are saying.........

did u make 365 free energy videos? one each day

i was into Newman motors 20 years back... i recently started looking into this again and stumbled over your genius videos ... ❤❤❤ ... I really them thanks so much!

Why is it that despite the thousands of man years and huge numbers of videos about free energy machines not one has ever been shown to work?

My n52 magnets 6 stacked together much smaller than yours have a magnetic field diameter of 2ft, the magnetic field strength of your giant ones is probably far greater than your coil magnetic fields, in physics is better something heavier is pushing something lighter then the other way around, this is obviously impacting your newman motor performance, the circuitry probably isnt the best idea either needs a sparking commutator

You need to try it eith a battery see if it stays charged, you use a main input so a back charge wouldn't work Newman only had a could of parts, you haven't even got a spark gap anywhere, read what Nikola tesla said about spark gaps

Would one be practical with a coil with near ZERO resistance?, if resistors are connected in parallel it halfs the resistance yes, what if 20 are in parallel it'll be 20x less resistance yes? Copper wire work the same thin 0.5mm 20wires need to be wound together as 1.

Could even just wind the coils more uniform to get better performance i.e every layer needs to be wind from the top to the bottom no layers winded from the bottom up to the top

Have you heard of a marx generator? Its a capacitor bank but its charged in parallel and it discharges in series, be easy to get 1,000v out

I will speak for Joseph, Why would someone become another example of this person. He was also losing at the end. Your running too little voltage also lose the spark its lost energy. Your comprehension of the motor generator is not great. Also there is no free energy not solar not anything also the amount of energy and resources needed are substantial. Keep learning. Never shoot the messenger. Also what law was broken from the thermodynamics? I feel you don't know what your talking about.

Did you get over unity?

Hi Patrick why did you not continue the newman motor because you was so close to very good results i am sure . You could minimize the investition with many smaller magnets and iron plates between them and maybe changing a little the design by adding 4 coils insted of 2 , perpendicular to have powering at every 90 degree of rotation . 4 switches and make like cube design .why stop man?

Yeah I totally agree about overcoming Lenz's Law. I'm in the process of building a Thane Heins transformer, he overcomes Lenz's Law by using high impedence coils. They some how seem to cancel out the back EMF.

Where is the heavy flywheel?

Does Axel angle for the magnets matter? In big eureka the axel was at an angle and turned a pump. I'm just wondering if anyone has tried the different angles and if changes the output.

Your understanding and explanation of the Adams motor is TOTALLY flawed. Please do your homework well, before you MISLEAD people. Bedini 'Motors' as per your information are NOT motors, because Bedini himself has said so. I have built and experimented with Adams motors and Bedini Energisers, for over 10 years now and from my hands on observations, I can confidently tell you, you are dead wrong.

Could it possibly be that the physical properties of newmans motor coupled with the hydrodynamics of the pump his motor was usng as a load created the balance needed when the magnets were at top of the peak? The waters motion within the drum depending on its oscillative motions, could have produced a kind of harmonic resonance relationship between the timing of the manual brushed commutator and the magnetic switching pulses. Water is also paramagnetic. Whether or not that property is in play there is unclear but... just adding some food for thought....

Veljko Milković has made already more efficient models with an elastic structure

Veljko Milković je napravio već efikasnije modele sa elastičnom strukturom

IN (w)---OUT(w) ????????????????????????????????????????????

I and my friend are working with the Thane hiens bitoroid overunity transformer. I am more technical than my friend who is not an engineer, he is a finance graduate. He consulted me on technical part and i guided him as per my engineering knowledge and experience. Because I am more technical than him so i did my calculations on paper first and then consulted him to follow the steps. Being more technical i rejected many ideas on paper itself such as connecting caps in series, however he being a non tech guy, he many times followed his intuition and at one time he connected the cap in series at input side and that reduced the input current drastically without reducing output at secondary when loaded. Knowledge restricts our creativity. U r doing a mental analysis of why Adam's motor shouldn't work, but when u try to build it in real, u will get new ideas and when you implement those ideas you will make it work. So inventions are about experimentation rather than examination, because we are not taught good in school textbooks.

What if you used thinner wire to get more turns and greater surface area, also maybe coat the wire in a layer of insulation

Can you make a traditional generator from this? Im curious to see how viable they are as a pedal generator Find the right gear ratio and g It should kick out considerable juice

What size and strength neodymium magnets inside the coil Patrick ?? Do you think using larger diameter and doubling the magnets would lower power consumption ??

This is just crazy, only a watt to run the machine. This is just incredible fella. Keep on making great videos Patrick.

DO you think that covering the open ends of coils with unique coils to increase the efficiency of the Newman motor ??? Would you agree with my statement or have a better idea Patrick in whch direction to go forward ?? Job well done Sir. I look forward to seeing more great videos with your stamp of approval on the subject matter.

COULD you tell us what is the method to get four to five hundred percent efficiency Patrick. Thanks

What I do not understand is the number of people who were involved with Joe on this adventure of energy and no one next working with Mr. Newman has not reproduced the motor he made when they all know the whole kit and caboodle about the machine. Now about the coils you have wound, There has to be a better coil layout to capture the maximum amount of magnetic flux from the spinning magnets. I know the mass of copper in the coil makes a difference at least that is what I would think. But I truly do not know Sir. Just hope your experiment will show you and us all the right way. Good luck to you Patrick. vf

What do you actually put into and get output with the unit you made Sir ?? Would covering the openings of the coil on the top and bottom of the spool make for an increase in power for you ?? Keep on experimenting with the motor generator Patrick. Look forward to see you make things happen. Keep us all informed too. vf

I just love watching this stuff

Bon appetit!

🐰

Dear Patrick, I hope you are well and still achieving. Newman was sound. I feel this has unearthed you a little. 15 people liked this, it makes me sad how few people actually seek truth. Mass in effect size matters.

where do you buy your coil of wires?

My old shop instructor would go off proper if anyone in the class ever left the key sitting in the chuck. He told us horror stories of the machine getting absent minded lay turned on, resulting in key being thrown into the general direction of the operator head at the tangential high speed. … if lucky, the key stays in the chuck and crashes the head against the bed … destroying the chuck at best, at worst, bends and or breaks bearing seats with the impact forces. Don’t mean to be a dick.. great work.. stay safe. 🧡

Could you run this if they turned off the grid sir?

Great work, really appreciate your honesty with your results from from your hard work. Just a suggestion, I believe that there is a great deal of promise in Thane Heins projects, perhaps you might want to check them out if haven't already, and maybe consider doing a build of the generator in that manner.

This way you would eliminate all the complicating switching .wich AC power

Hi Patrick how about if you use an ups or an inverter with sinewave on this newman motor and you colect the bemf trought diodes you think would be posible and use little power and the work would be smoth and the power amazing like on an mono phase induction clasic motor .

Hola Patrick , ha intentado conectando dos motores identicos , uno como dinamo de ac y otro como motor ? No es pretendiendo energia libre pero si para ver la eficiencia y a la vez eliminar transistores para la conmutacion , unicamente provando con el condensador buscando que los motores entren en resonancia , adicionalmente instalar una polea mas grande para mantener mas tiempo la inercia, la capasidad del condensador depende de las revoluciones (hay que exparimentar ) . interesante el laboratorio de este motor porque el nucleo de la bobina son los imanes lo que lo hace muy eficiente . gracias por publicar exitos!. Traducir a ingles.

The magic box thought process you were referring to sounds a whole lot like the concept that the kundel magnet motor is based on. It's an interesting concept for sure.

Big up to you Patrick. You have done fantastic work so far and proved that there's no fixed boundary when it comes to science. Lots of theoretical 'regulations' to be challenged by bright people like yourself. Our education system can be great but can also encapsulate us within the boundaries which are taught. I watched the documentary on Joseph Newman and was quite perplexed by his behavior. He came across very obnoxious and paranoid. I do believe that the models he displayed were genuine working models and by the size of them fit - which your description of the size required to make these motors useful for power generation, but I think he had hidden doubts because perhaps he was unable to tune his motors to precision efficiency to generate enough power to make them viable. Perhaps if he had not faced such resistance from the onset things might have gone in a different direction. Sad that he dismantled his machine before he died taking his unshared knowledge with him to his grave.

Is there a clear explanation of the principle behind the Newman motor ? How does it work ?

Hi Patrick very nice work , can you please tell me which transistors or mosfets you find best for high voltages to use on the newman machine? Thank you alot.

intersting video you're watching in the beginning, can you offer me a link?

Ah sowas Gut

brilliant, more relevant now than ever

have you met chris sykes?

New video a lot of work Wow