Відео

What’s stopping the battery from draining straight into my lithium battery? I’m trying not to make a mistake. I want to add a dc2dc for my lithium battery to a px1 ranger.

Great video! Thanks for helping me identify which was a ignition fuse.

Update on my previous comment. Got the job done, works great. Just need to take time & find something to pull cable through tight spots. Cable ties were really tight in places so used spare wire to push end of cable tie to where I could use 1 hand to attach properly.

What I hadn’t considered was how difficult it is running the cable When you have the ARB 140l fuel tank installed. There is almost no way to get your hands in place to pull cable or to tie it to the ford harness. Can’t see how cable will fit under fuel filler as there is hardly any gap at all. It’s taking me forever. Going to be a bit of a bodgey job I’m afraid. Not fault of product just me

What about an option for rear seat mounted second battery?

Thanks for this video. You must have the smallest hands of any known body. It took me about 2 hours to get the wire through the grommet. I ended up putting a flat screwdriver through the grommet to give a space for the cable. There was not room for two hands between the brake actuator near that grommet. I did contemplate putting a hole in the grommet but persisted and it appears to work. The hole in the rear was the easiest part.

Where did you get your bullbar from?

Nice video. Thanks. Just wondering why did you choose Delkor hdt27? I am after an auxiliary battery.

Best video on this subject. Everything explained and shown. Thanks for taking the time to help.

Do you by any chance know which is the speaker wires?? I can’t find any, took off the passenger trim floor and cannot figure out which one to look for. Need left rear back wire colors so I can tap into them

This guy knows his stuff 👨‍🔧🚗

Thanks so much for this video, this is the only one out of all the 12V system installs that actually show how to run the cable to the back of your vehicle! Thanks mate, appreciate the video!

Thank you for the explanation.. very helpful. On your site now to purchase some items.

Very well explained. Steve

Is there an earth wiring location or bolt in the back somewhere?

What size cable are you using to run to the back on the accessories harness? And would you be safely be able to run a fridge and other accessories off of it?

Hi there. Is it possible to disconnect the smart alternator?

Does it stop you from adding a snorkel , with the battery tray on that side near air box ?

why dont you use the start,run wire behind the hood hatch leaver release just up and above that pannel just tucked behind the loom. for IGN curcuit? I can see why useing a fuse tap is easier as all the wiring is just thier, im just curiues why people are not using the wire ford provides. Nothing wrong with how it done at all looks good. just yea

Fused?

Best video on UA-cam. Thx for detailed info.

This is where I'm at. Wish to cut into existing wiring under the bonnet for cig lighter so it is permanently live. But powered by aux battery only. Intend to fit Anderson plug at later stage as per your next posting.

Great input. I did notice were you tapped into the fuse BOX for dc dc charger you had your finger covering the exact same spot i had to nibble a little bit of plastic out also to fit my wire thro. 😆 thought there be an better way but it was the easiest solution at the time..

Makes life difficult using the big impact drill instead of using 2 x spanners! Seems to be some kind of obsession with a lot of installers using power tools where spanner/socket would suffice and reduce the risk of damage or stripping bolts. Not always quicker, either.

Good video. Well explained. Would the kit be suitable for a 2019 Prado (1GD) ? Cheers

This is the best, most thorough video for this install. Thank you very much mate

G'day, great video. What did you do with the original harness under the tub? Did you leave it there and seal it up ? Cheers

Hello! Could you make a video about the 12 pin trailer connector on the new ranger? Could I charge the battery of the rolling box with that connector? Thank you so much

Great installation guide. Made the job so simple

spot on

Why installing 2 batteries ?

Cheers. Where did you connect the blue wire?

Awesome vids and products mate. I just purchased and installed the Prado150 kit you sell with accessory harness, battery tray and redarc charger. Saved heaps of time compared to previous installations I have done in other vehicles using only the redarc wiring kit. 😊

Awesome, could it apply to my 2007 american version ranger?

Can’t we take the positive condition from roof light and take ground?

Quick & Clear

Hi all, very good videos and instructions!! quite easy to follow and I'm looking to purchase the complete kit. But I've got the Next Gen Everest sport 2023 and would appreciate if you could record a video showing the accessories harness installation. Thank you.

Thanks Drifter. Great video. I have this already installed on my troopy, But the extra support arm bracket was not fitted correctly. Bolt had no nut holding it in place. Will pull everything out and redo it. Much appreciated. Great! Thanks for making such a detailed video instruction.

🌺 Promo SM

Hello, can you show me how to change engine air filter ?

Would really like to see a video on Installing the Accessory Harness in an Next Gen Ford Everest, waiting for mine to arrive in July

Good vid. Shows it well

thanks 🙏🏻

Crystal clear instructions. Thank you!

Hi mate, great video. If ordering do you ship to NZ?

How would you approach the grommet situation if you already have a cable running through with its own grommet?

The cable routing should have its own video lmao JK. great vid mate. Did you have to disconnect the negative on the main while installing the unit?

Great Vedio to watch and understad.

Hello, do you have any instructions on how to run cables from roofrack to the rear of a vehicle, I have lc200

Where do you buy all the accessories from.