Відео

Where could I find plans for this?

I have the same car and just replaced my fan in about 30 minutes. I removed the tabs that were blocked by hoses by using a reciprocating saw and it popped out easily. You def have to wiggle it and move some hoses but it's easy Installing it was not too bad. The only thing I had to move was the large radiator hose on the passenger side and the fan dropped in easily. A little bending was necessary but it was about a 3/10 on the difficulty scale. This video is appreciated but way over the top.

Please stop saying gallons per minute, its gallons per hour. Just imagine a pump with 3,000 GPM - you could fly to the moon with all this power!!!

Thank you. I never put a cover on a pontoon boat before but with this video it was easy. That's for sharing

I got a cx60 2011 and am thinking the fan assembly is hoped

I apperiacte the effort you put into this video, Thank you.

😊 amazing

Do these as a pair at the dealership. And no coolant hose removal needed. Just a lot of wiggling and bending to get the assembly out and in.

July 2024 New Boat Perfect instructions. Simple step by step. Thanks 🙏 😊 My cover came with my boat :-)

Create an Ebook and sale it online digital marketing

Mike are you in Arizona?

Would it make sense to have the top crossmenber straddle the sides of the trailer. Just a suggestion.

Mike hi, sorry to bother but I just wanted to hear your opinion about it after 4 years now as I am thinking to start something similar. Are you still running this? Any good luck? Thanks for your time! Have a great day/week ahead!

Same fan module and control unit for Land Rover Freelander II 2007-

Can you make me one?

"welds"

sorry for my english any recommandation for me , wanna carry 5 or 10 ice cream topping any design recommandation ?

What kind of glue was that in the caulking gun ???? Brand ??? Lowe’s ???

RIP Jeff Spira. Earth lost one of its best artisans when he passed.

Would you be willing to sell it?

If you put the restrictor plate and ECU from a 20hp in the 9.9....Alakazam!!!.... You have a 20hp that still says it's a 9.9 on the cover. It can be done for a $100 if the Ebay ECU Gods smile on you.....Allegedly if you just remove the restrictor plate 9.9 becomes the 15hp without any further mods, but research any mod before you do it and decide for yourself 👍

I'll share my same scenario with my XC90. Unlike the S80, the XC90 has a temperature meter at the dash. This problem happened when my temperature sensor failed, rendering no temperature reading to the ECU. The ECU is smart to detect this failure, and to prevent overheating due to "no temperature signal", would run the fan aggressively and continue to run it for like 3-5 minutes after the engine is stopped.

She handles really well, Skip, aye-aye ! A clear & helpful assembly account throughout, spoken in a pleasant & well-paced voice. 🌿🙏

Great video! What changes would you have made after using it?

Where to buy the materials, specially the metal pieces please

11:19. I just read in VIDA that if you push the bottom of the fan toward the rear of the car it will clear all obstructions. Never tried this but may help someone else if they need to remove the fan.

Any recommendation on how to make it beach friendly? We have a sand roadway, considering doing this but concerned it may sink in the sand… hmm 🤔

I really appreciate your great story telling method! Im in a time emergency so I’m at a specialized dealership that does the work much cheaper. But now I know for the future! Thanks

I want to built this exact boat. Can't find the plans to the Seneca. Jeff's website is not working. Any advice?

Ok. This is the best explanation I’ve ever seen for a technical problem on a car. I am planning to buy a S80 T6, so I think I may need this in the future.

I have watched dozens of builders videos, both experienced and inexperienced (the latter actually tend to be better as far as identifying pitfalls), in preparing to start a boat myself. One myth I have found very consistent for many builders, including some of the experienced folks, is that wetting or soaking lumber helps to make it more flexible. I have 45 years as a furniture maker and the reality is that this myth started because of the practice of steam bending. People concluded that it is the moisture that creates the flexibility. Reality is that it is the heat, not the moisture, that makes the cellulose (that is basically the glue within the wood cells) flexible; like heating plastic to make it flexible. The moisture in the steam insures that you do not dry out the wood making the surface brittle while heating and the fact that steam transfers heat energy at a much higher rate than dry air while also insuring that he temperature will never exceed 212F degrees. So soaking may help in a very minor way with some wood but the reality is that fully cured/dried wood can sit in water for years without the water penetrating any further than the first few layers of cells. If you need to bend solids you are best off to build a little steam generator of some sort and place your wood into an appropriate container that will contain the steam (In college we did some steam bent furniture for a design class by making a steamer using a propane deep fryer with a pipe attached thru the lid going into a long piece of 6" PVC pipe. By raking the pipe at a down angle and drilling a small escape hole at the capped end the steam was able to flow thru the pipe and condensed water escaped thru the hole. 12 hours in the steamer and 1/2" white oak strips would easily bend around fairly tight curves). Absolutely love all the first time builder videos.

Great job on your boat. And thanks for sharing the build process and your decisions with the world. How is it holding up? I'm worried about maintaining a wooden boat in the cold wet climate of Washington.

Thank u

Amigo ayuda no trae esa funcion en elbtablero

Have your own food bike building business

I almost don’t even care if this fixes my issue. I’m making the swap anyway. What an on point video! 5 ⭐️’s

Thank you! Perfect video! Huge help!

How much did all the resin and paint and fiberglass cost for the whole boat ???

What did you think the paint with ???

Olive is such a heroic companion

Great showmanship, easily understood by me

Do you have any hints on how to program the display? The manual states I can turn off certain features that I don't want to see? Because the process steps/instructions are incomplete I can't tell whether the step is complete? Or, maybe I just misunderstood the function description. Have you found that you can hide certain display features such as mileage and incline and calories burned? All I want to see is the TIME. My display also has curious Greek looking letters as its' welcoming display? It might be the word HELLO but t's all screwed up! What's that all about? Thank you to anyone who may have some answers.

LEGEND!!

Very nice job 👍

Very helpful, Thanks. Just ordered the control unit, hoping that will fix my situation and I don't have to replace the whole fan unit.

Ya maybe probaly could have used a cable tie or two

Nice testing procedure

Its not gouging. They can charge whatever they want. Its their labor and tools and shop

ALLWAYS use masking tape when you appy silicone or thick glue, remove as soon as glue applied so it won't dry into the seam. Your tip with the carving in the joints is great. will do it to the boat I'm busy with now.

Brilliant, but instead of modifying the lower bracket you can actually remove the tranny cooler unit by removing one screw then pull the unit out, wish I could attach a picture on the app!! Good job!