Відео

Nice job, so even though this Inline Fabrication mount is called a flush mount, it isn't necessary to use a router to cut the wood, as some guys have shown on other UA-cam videos. My last unit was the higher unit or what they call the ULTRA Mount.

We found Staball had smaller groups with large rifle primers..

The Heat INdex of N160 makes it a very cool burning powder compared to many other powders. AA2700 is the coolest burning powder. These cooler burning powders greatly increase barrel life.

Great work. I appreciate your idea of reloading the same loads and push them to 500. Sounds super smart to me!

I run 58.0 with 140 Accubonds and no pressure signs. 1/2 for 3 shots since it’s a hunting load.

I’ve had really good success with it using 140 Accubonds Berger Elite and ABLRs.

Thank you for your idea of "charging/ seating, then in the range box". That is a time saver. I've had an old routine where I do 1 operation to completion, clean up, then move on. Your idea showed me how much time I waste waiting for the powder measure to "beep". In the past while it's dispensing, I THOUGHT I was being efficient by champh/debur the next case but I still had maybe 20 seconds left to wait for the charge. I COULD HAVE SEATED THE BULLET AS WELL!! What a dummy I have been. Thank you so much.

Really good video

that was sick! thanks again brotha

Good stuff!

Great job 👍

Hi, do you have to lube some parts and are you satisfy with this front rest? For the price it seems a good buy. Would you buy it again after using it? Thank you

Thats a lot of rounds down the barrel for load development. I can’t imagine the groups are very good yanking the trigger like that…😮

I watched it twice. What are the details on the firearm & optic? If it's there, I missed it; twice

78.2 is looking promising with that 8.32 SD and that group is like 1/2 moa w/o the flyer. Maybe try it again ans play with seating depth? Seems like that would be a better load for passed 1000 yard stuff. Love your content, man. I recently finished my 300prc project (Kelbly's/26" 1-8.5 pac-nor/KRG Bravo/triggertech/Tract Toric ) and just got some retumbo and 225 eldm's to do some load development with. Your videos are very helpful.

I have four different presses. A RCBS Rock Chucker II, a Lee Classic Cast Press, and two MEC shotshell presses. One 12ga, and one 20ga. Also, an RCBS primer pocket swager. They all are rock solid with their individual base plates. I plan to add another base plate for a vise. The In Line Fabrication is the best system, by far, for mounting any type of press. If you have an oddball press, send them a tracing of the footplate, and they will custom make a one-off plate for you. Or provide you with a blank if you wish to make your own.

Moving up In .1 increments is kind of a waste of time and components

I'm guessing you need a base mounting plate for each press you want to mount on the bench? How much are they? are they easy to find?

What is your barrel length

The 15 shot ladder test is invalid given typical shot to shot velocity variation. You are basing your load development on random noise.

Good afternoon friend, greetings from Spain, congratulations on your videos. One question, I bought that same one (bullet pointing die) now I need the B-20 punch for Berger 200.20x cal30 tips, and I can't find where to buy it and have it sent to Spain 😓 Do you know where I could buy it? Thanks for your time . David

Interesting stuff, neat seeing that big cartridge deliver such compelling results. You did see something that I've seen int he past, and that's the groups with the best standard deviation not always having the tightest group. I dunno why that is, but I don't sweat it too much. Some guns just like different amounts of powder.

I have the same rifle, is there a part number for the weights?

You need to get a Henderson man..

You like wasting powder and components? 0.1 gr increments is ridiculous... Same with 2 thou seating depth, makes no sense whatsoever.

You went little backwards buddy the further the shoulder is blown out on the case your loading, over your oal case you used to check the seating depth with the further you have to seat the bullet out out the case bc the front of your brass is gonna hit the front of the chamber sooner than it would 3 tho smaller so instead of you being 20 tho off the lands like you wanted you were 26tho.. which isn’t bad. the case your loading is 3 tho bigger than you oal case then you seated the bullet in further 3 tho off the lands. but great video man!

cool, nice to see you get some new videos up. in my experience, the ES's aren't as consistent for the first 150 to 200 rounds. that's just from shooting and reloading for F-class for 10 years. it's great to see you got a new barrel. what barrel is it? it looks like it is gonna be a shooter.

Those things are the berries aren't they? Lol

Nice

Good Luck finding retumbo, Sh*t is going for 65$ a lb on Gunbroker.

Get rid of the Bi pod, good things will happen!!!

Would be a lot more interesting video if you had a target cam

You missed to provide information on rifle. Is it Uintah Precision? Also have you tried StaBALL 6.5 with 224 Valkyrie? It should give much larger velocities that even with 88gr Hornady ELD you should reach 2700fps. that should give you far more chance for modes with low SD.

I plan on using the 6.5 Staball in my begara 6.5 creedmore with 130 grain scirocco moly coated what is a starting load you would recommend Norma large rifle brass and CCI 200 primers

After more than 50yrs @ the loading bench I can tell you that seating depth will tell you more than 1/10th grain of powder & cost less in components & barrel wear ! With cases as large as the 300prc work up in 1/2 gr increments to get the velocities & ES you need , refine seating depth , then test different power charges + or - a 10th . Just a suggestion to save you time , money and barrel wear . CHEERS AND GOOD SHOOTING

Speeds thru a chronograph would have been cool ….good work 👍🏽

Would love to see more 300 prc videos

Americans 😴

what round?

How do like the arbor press?

What ammo and gun you using

That looks bulletproof. I like it.

You can reduce SD by using Mandel in place of ball expander. You will need to try a few sizes. Also coating the bullets bearing surface with neolube2 it will instantly lower SD. Neck tension and release friction has a large effect on consistency

try retumbo and 140 berger hybrids i shoot a 6.5 x284 N and get 2990 with es of 7and sd of 5.......

What projectile are you using?

Play with seating depth and different primers and bullets ( Federal Match Primers-Berger Bullets 140 Grain Elite Hunter) might do to lower the SD's and ES's

See if sorting primers shrink those SDs and ESs

You should have developed the powder charge with the lowest SD and ES first the experiment with seating depth. You need a chronograph in order to do this effectively. .

What does that unit weigh in at ? I am looking at that same one on Amazon 233 bucks.