Відео

It’s 2024 and my local Kubota dealer is selling this belt for 90$! I see belts on Amazon for 30 bucks. Anyone have any thoughts on knock off belts vs Kubota made?

Easier with those boards in gardens I use pins because were tight up against boundaries

This is so easy to do. Why even make a video

The battery in your meter may be going dead

It took me 2 weeks but I got the belt on.

So now you gotta widen the holes ?

Glad this video was made.. helped take the stress out of this project

will this work on the foord 2000,3000 and 4000?

Nice ❤

It's too for 2011

Had the hardest time trying to get this unstuck today will try this tomorrow

Perfect❤

Lifesaver!! For 4.6 is the same thing except you dont have to take off the cover. Just the ecm bracket. So even easier.

Great video! Appreciate the content!

My wife likes mine to stay up! All jokes aside… thanks for posting this mower deck staying up video. My zg 127s 54” is having the same issue. I’m going to try to shorten the stroke as you’re suggesting.

Whats the best bait in that area

Thx Man! Exactly what i needed!!

Boa noite meu amigo

Learn to change these belts yourself. Definitely need a lift or good jack. I tried myself but got frustrated and just ran out of free time. I pinched the drive belt at one point so I needed a new one ($31) and I already had purchased the new deck belt ($150). I dropped off at my local Kubota dealer and just picked it up today. Here you go….New drive belt $31, shop supplies $31.39, Labor $418.50 for a grand total of $528.04‼️ For a company that does this weekly and has lifts I think this is %#%# highway robbery. I have a 2018 Kommander 48” z121s.

Hey do you remember the belt size

the brake wear indicator that metal strip you called a spring clip goes on inside of caliper it was on that side with old pads you took off

Thank you sir! Couldn't have done it without you!🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹

Good video. I ended up taking the tensioner pulleys off so I could have room to run the belt above the fan blades then I managed to put it all back together. I can't believe Kubota designed it that way. Although I've used this mower hard for years and I've only had to replace (before this belt) was the spindle wheels but that was a warranty claim so I can't complain too much.

Thanks for that. 1) It is also good to grease the ears of the new brake pads. 2) I recommend pulling out and inspecting the caliper pins. They need to slide freely in the bore. They are about $12 a pair to replace, but may be fine to clean, grease, and reuse.

Nice croc’s😅

Excellent Video. Do you have to have a heading sensor or Steady Cast?

Fantastic, rock on and thank you!

Did you ever figure out the problem . Thanks for the video

Pb blaster is way better than wd. Remember that.

Thanks for taking the time to do this video

What is the name of that blue part you connected at the reverse green cable?

Great job videoing this, appreciate it man

Thanks for tip ty

Just a note, you need to grease the friction clip points. You should not grease the back of the pad. You do not want that slipping you want to ends where pad clips to be greased.

The problem for me is the pin is stuck lol

I just took my rose bud torch to it. 🤣 5 min job. Never turning it over again.

Neighbor has the same problem but wants to buy a new one online. He asked if I knew the name for it --I didn't. Does anyone know the name of this lock unlock cylinder. We can't seem to find it.

Finally a video that shows where the glow plug harness connects to……👍

Thanks lol I thought I was crazy

For anyone wondering the first 9 minutes of this video is useless. If you’re getting a glow plug code pull them all and replace them.

Thanks for the vid I thought i was the only one

when the river is running at night is my favorite. pretty close to the bank. and they hit hard. better have good rod holders ,,,

I was right there today. getting my fishing hole ready for the run . lots of trees down in the water ,, but I still have two spots that I can use. absolutely love it there, fishing it my whole life .. Im 65 and I never miss the run, chicken livers and shrimp is my bait for the white bass and stripers ..too bad they are full of PCBs and not good for eating

Awesome what would one be worth good shape 2500 hours?

I love the way you did the color Jon

Must be an early 04 engine or left over. I believe it was 04 when they switched to the 3v. Be happy you didn't end up with one of them piles of junk. Anyway, fixin' to do my #4 as well, thanks for the look.

Ive come to the conclusion that im just too stupid, i just built a small shed 15 ×20 to be exact and used round posts to frame it. I measured like a mad man and used every video of how to square a layout for a building and it turned out to be a complete fuck up. The shed is done and it doesn't leak but its not evem close to being square. Luckily its just a farm shed that no one will see really so thats good. I just ha e never felt more ignorant and foolish about myself than building that shed. Im enveous of guys like yourself who can calculate this stuff so easily. I feel stupid writing this comment😂

I don’t keep the ball in the hitch when not in use. The ball is exposed beneath the truck and gets coated with dust, dirt, mud, whatever. I cut a wooden block that just fits into the hitch when I’m not towing.

Que tipo de starter colocaste por el starter viejo.

Where did you bought this starter if you still have that link please share Thanks