Відео

Hi, I’m not sure if you still see comments here. But my treadmill belt is sliding to the side and rubbing up against the plastic. We’ve tightened all the bolts, made sure it’s aligned properly, etc. But it is still sliding to the side. Any recommendations?

Thanks a lot for the video. It is great help

Pretty sure the other guy pays tax and shipping. They do charge you a fee but it's not tax when you are selling lol. And buyer pays shipping. The fee is still too high

Support Bracket Screw - Ford (W506964-S437) if you drop or lose like I did from unscrewing to much

🚴🚲🚴‍♀️🚵❤❤❤❤❤

It's just a 2 dollar bag of ice and a long weekend?

My 06 wrangler is missing and throwing a po301 code,I replaced plugs,still misses,I'll try replacing the coil pack if I can get to that plug on ot.

Thanks for the share 👌🏽 was good fast quick learn 🫰🏽

Thank You so much for this video. My combo unit went out the day before Christmas. The oven reset by cycling the breaker. The microwave needed the fuse replacement. The hardest part was pulling the oven out of the wall and not getting crushed by it.

Given how much effort i just used with a propper bearing packer to regrease my trailer bearings. I cant see these forcing grease through the front bearing , through the entire free space in the hub and then forcing new grease into the rear bearings like some of you claim. Ive used these and the amount of grease put in till full never even filled the cavity around the axle inside the hubs to force new grease inside rear bearings. So duno what eveyone is on about but could be just what happend with mine.

Very helpfull video thanks. Just one question though. Did the metal screws not spark after installing?

How often wondered about that thanks for showing me cuz I kind of wondered that too

Thank You (:

hahahahaha! OMG man!! it is a great video , your reaction is priceless. I was equally surprised ! =P cheers man!

Thanks for the laugh on removing the seal. Good video demo, appreciate it!

Homemade Polar Bear tubes for the win. Ice lasts much longer with polar bear tubes and unmodified coolers.

@3:17😂

All premium coolers have full insulation and a rubber seal - this isn’t rocket science !!! ua-cam.com/video/7tsbXFg1_JA/v-deo.htmlsi=2o1UUTm4MYb_4pfE

Listen dummies if air is a good insulator then why do coolers have insulated boxes and why is foam used in home walls and other areas (as one type of thermal insulating )? There are some confident ignoramuses spouting nonsense in this thread !!

Something fishy about this test

Name of this part is wave guide cover

Great job and well done explaining how to unclip the connector in the back.

why hasn't offerup reply?

Hey, i appreciate how good you are to troubleshoot. You are a good teacher if you are one. Very detailed and easy to understand. THANK you very much.

Maybe swap the lids maybe the cooler itself

Do you have to deflate the inner tube completely before you apply?

Thank you

Super helpful video. Thank you!

Why didn't any one inslat the rest of the ice chest? We had to live out of our ice chest for two months while are LG rrefrigerator was being fixed. You insulate the top but not the bottom why? on a house do you insulate the roof only, you guys don't make since

Man, I have an Idea... Get a total of 3 small cheap foam coolers that will fit inside any of the plastic ones and here is what you will do. Foam cooler by itself Cheap plastic cooler by itself Expensive cooler by itself Foam cooler inside cheap cooler Foam cooler inside expensive one Lets see how much it helps adding that extra layer The coolers on their own will be a base line to compare to. The combined coolers will show if you can improove on an expensive cooler even more or not, if you can mimic the expensive cooler performance using 2 cheap ones and if the cheap ones can be improoved at all.

If you create annother layer with the foam instead of replacing the air volume in the cooler you will absolutely improove the cooler performance. The problem is that air volume is one of the best insulators, foam actually works because it has a lot of air or gas pockets inside it and that helps create a less conductive material, but pure air is much better than that. Actually, a cooler inside a cooler would be ideal, you have 3 insulation layers (the small cooler, the air between the first and the secind cooler and the final cooler itself). As well as a double seal.

I can’t believe how much DitchIt has helped me clear out my space and find new items I actually need. The process is so simple, and I love that it feels like a community. So grateful for this app!

I can't believe how much time I've saved with Ditchit. It's amazing!

What a freak, he kept the phone, and he's fixing it, and he didn't send your payment, I pray for God blessings on your account

Thank you, very helpful

Super helpful-thanks 👏

Do u see that white cap on the cooler you take that off and you fill it with water and freeze it the your beer or ice stays colder

My microwave was making a sizzling/water sound for quite some time. Now the light keeps flicking on and off. I had to unplug it. Do you think its the same problem as yours?

Now when I tighten up the bearing I can deal with all that extra grease! :)

Terrible lighting, but good video otherwise. Thanks.

I have 255 30 24 on the front of my magnum and 275 25 24 on the rear and all i did was the same as here and i have no problems no rub an inside the wheel wells

merci monsieur❤

Great video, thanks a lot!

Well I learned something new but it's too late the inside of my microwave melted, time for a new one I think.

straight six partner

Replaced all the speakers in my 2002 Wrangler. Thanks for your help!

Best vdo out there for this thank you for this

You explained the process very well thank you very much for the video

Two of the three holes for my washer bottle are missing or in the wrong place so I need to drill two holes and tap them. Mine is stock and the hardest part was putting the stock fender flairs back on.

Try it in the sun where the insulation in the top should help with the direct sunlight.