Відео

Hello, here’s my question I peeled off the protective cover on the back of my car once the holes are reamed wet stop the paint from getting on the outside? because you have the car on the roof. Thanks please help me out.

Hey how are you doing I'm James I have a monte carlo 1979 lowrider rc do you do paint jobs on this I have the body and I'm willing to pay for this paint job

Mine keeps coming loose and tricks any thing is new

U didn't show us how to mesh gears?

I’m a tech at a Traxxas hobby shop. Super experienced with Traxxas trucks. I’ve watch a ton of repair guides in my time and this one is VERY well done man. Congrats and thank you

Piss poor engineering, but a great video of how to disassemble. Who would design something like this 😮

When that noise comes that means you broke it the super clutch you broke it and you know that that's loose again the middle of this

I think you're missing a bearing that goes between the two out put gears to join them

Best how to on UA-cam I’ve watched so far! Great job sir! 👏

I've had mine for 2 weeks running on 2s lipo. After a 20 minute run it shut off because of heat, so I thought. The next day it wouldn't move and after some trouble shooting, it turns out one of the fingers holding the brushes on snapped off. lol

You did not show how to reconnect the motor to the diff

I burned out the old 550 MEGA 12 that my Arrma Sento came stock with by running a 22t pinion gear in it... I think I killed it. I unfortunately refuse to downgrade my pinion gear though and hope this motor conversion lets me keep running it.

I have bad hands and found that getting a 7MM wrench with a larger diameter handle makes putting the wheels on/off much much easier. I found a cheap one on Amazon and bought a pair of them. One at home, one in the car toolbox. Brand is Auvotuis. I was using a wrench like you did in the video and it was difficult to remove the nut. Too many cars worked on, too many fights as a bouncer, and old age make your hands hurt!

To set the slipper its 1.5 turns out thats factory

Doesn’t work, my esc and receiver are built into one, followd this video and just ended up having to spend more money

I just got a clear body for my rc truck. Didn't even occur to me to paint the inside of the body, lol. Thank you for the video. What exact brand(s) of the metallic backer and paint did you use. You might have said it but I missed it. Thanks again!

What color red is it please metallic???

So it's a 2mm to take out the screw and a 2.5..to put it back in and do you need to put thread locker on the screw ??

Thank you your video helped me fix my arm.

Myself I score the body all around with the hobby knife then I cut out the wheels but I see you did a good job came out really nice bud

This was very helpful, thank you.

So what size Lipo is in it? And did the stock ESC handle the battery upgrade ok???

Awesome job

Are the 2.5mm and 2mm driver torx or???

Is it the same arm as on the granite? And have you heard of people using a little longer arms? I just broke a front a arm , very front where the pin slides in, and I'm looking at these aluminum one's now but want just a bit more width on it to add stabilization. Already done shocks. Any time your not busy if you happen to know. I know that this is a senton. I'm really pretty new to this. Got tools though and the means to upgrade. Just want to go in the right direction, strength and stability. Thanks

It was a month ago I tore into this thing and got a new motor. Thanks for showing me what I forgot. It runs like new again!

But what about the bearings? How to get the one off the back side?

Thanks! Well made!

This was so helpful thanks so much dude

My engine is brand new but I broke of the little hook for the battery wire on the engine mount.. wonder is it’s even worth it to buy a new one and take everything apart? It really dose not effect anything.. it’s just bothering me haha

I have the same exact setup with the red version. My stock esc malfunctioned and did a runaway causing the esc and motor to smoke. So this upgrade had a reason lurking behind it.

thank you so much, me and my dad stayed up all night taking the entire rear end apart, i would have never guessed you snap it right off

How to break your slipper hub lol

Nice job, really sexy.

just got a brushless, thanks for showing how to replace motor.

Hola, vi que no usaste pintura Tamiya ¿Que marca es la que usaste?

Very helpful! Thank you!

Get the new clutch

Please tell me how you did this with the sour gear I’m stuck

First time owning a nice RC truck I had it one day and I got a little rock in the motor your video is very helpful to someone who is new to the hobby

Has this ESC and Brushless motor have given you any problems? I just bought me a 4x4 Senton Brushed on sale.

What the code of this pain?? Is that lawa orange? Or candy red?

Also what spur gear do you need to run that 130 motor combo for the senton mega

What size pinion gear do you need for that 130 amp motor?

Perfect this is exactly what I was doing

Thanks a lot. Never would have known how to get the motor out without this. Had trouble getting that little gear off the old motor. It was really stuck on there. Happened to have a hammer nearby. Used the claw end and pryed it right off!

Have you had any issues with this motor? I just installed mine, and something has came apart internally, after only 1 battery

The loud SNAP let’s you know it’s working.

? What was the paint on the body at beginning video "chameleon"

Good video took time to explain the stuff and not rushing through it, keep the videos coming.