Відео

Turn the ignition on amd repleace the parking brake as normal and then wind back with wind back tool. Once new discs and pads are all fitted just put the parking brake back on. Will work fine l.

I also have the same problem i.e. damaged plastic connector housings. This vid showed me how to tackle the replacement job. Many thanks.

Looks stock mine moves up in 3 increments

Hello, this comment is not related to this video, but i've watched your dsg conversion and i wanted to ask a thing or two. Do i need to code something when i'm done with the wiring and will vcds do the job? Thanks in advance!

Hello, is it possible to put this DQ 250 gearbox in the Jetta 2.5 that uses the 09g gearbox?

Aaaarrrrrggggggghhhh. F'ing connectors ... Thank you

Do you which wire to connect that yellow and red wire too. I have a golf r press brake to start. Thanks

nice video man. thanks. Im trying to do a "basic settings" procedure (as in your video) for my DSG6 transmission in my Seat Altea 2005 2.0 FSI. But for some reason my VCDS pages/groups dont match. I have a HEX-V2 adapter cable. my VCDS is version 23.3.1 (sop newer then the video). For some reaon my ATF temps are in group 008 and 010 and not in 019 like they show in the video. 019 actually just shows ERROR. Then I went into "basic settings" and looked up group 061 and it just shows ERROR. Neither are the other groups they mention in the video. What am I doing wrong? any ideas?

My only experience with this engine was that it leaked EVERYWHERE, Burned coolant, leaked oil from the waterpump, valve cover, and oil pan. It was grandpa driven and well maintained, at 80k miles. Truly it was hot garbage. (2013 Tiguan)

in the middle of this swap on a VR6 swapped Tiguan. Am i correct to get it to drive you did zero ECU/TCU coding? all wiring no computer adjustments?

Hlo sir i have replaced my mk6 jetta spring or rebbion but my cruise control is not working it comes with ! This icon . Please help me out to find a solution

Yes sir

Hi. Was it just plug and play.

Is it stock or have you done a few things? Also are you just holding down the traction control button to turn everything off. My truck keeps defueling when I try to get down like that.

Can we able to convert 2016 jetta 1.4 tsi manual to dsg? And what would be the cost

Hey dude. How do you determine if your software is above or below the one it specified other than it coming up error not available? Thanks in advance

Do I need to empty my tank before doing this? My tank is full but one guy said it would overflow if I don't bring it down to 1/4 tank first.

yo what mods have you done besides the exhaust and intakes?

How do you reset the brake light in this instance?

Stock turbo and intake?

You can also take the black Parking brake box off of the caliper and rewind that plunger inside of there with a drill and I believe its a T25 or T30 Torx or equivalent size allen bit. Much easier doing it that way honestly. Took me like 20 minutes to do the whole job.

What’s your tune??

Does this work for a mk4?

No offense, but you guys doing car videos have to get gopros

My stock golf tdi runs better than that.. you should check your tune

summarizing, all that have to be done is to pull the stock tune ecu file off to remove the tcm communication error code and then flash the stock tune ecu file back on the ecu to solve engine light issue. And as an option, you can reflash using a GTI tune ecu to have quicker shifts. Is that correct?

Hi, nice work!! I trying to conclude a 09G to DQ500 swap, but my switch lever stuck at P with P light blinking. I connected the two can wire, a disconnected the pin 3 wire in the lever connector. Can you help me?

ASV valve issues ?

Thanks. Prepping for spark plug replacement and was concerned about the coil connectors breaking. After watching this I feel more at ease.

Thanks for sharing. It’s best not to apply power to the actuator like that, especially when it meets resistance like that, as there are belt drives and gear drives within the actuator that can be damaged. Best to remove the actuator and wind the brake by hand. This is of course in the absence of a scan tool, or diagnostic software which is ultimately best practice.

How did you fix the U0101 code?

thanks. Hello, would it work for Tiguan 2009?

Great vid thank you, but how did you release the brake with gnision switched off, or did you leave keys in ignision ?.

Rolling coal? Bad tune. Do better

😎

Would a 16 inch pry bar be long enough?

Got my swap up and running, however I cant find out where to put pin 7 on the DQ250 connector. It is the speed signal wire, do you remember where you connected it?

Is there any chance you have a basic parts list for this!?

Hello. Is same Procedure for when changing the mechatronic unit?

I got a stage 2 tiguan right now. Thinking k04.. but you think an engine rebuild is needed for this? Was looking at an HPA Turbo.

Thank you so much. 🎉🎉🎉

Thanks for that video. Still relevant after 2 years 🎉

Because all VAG are garbage!

Tell me what the reason is, the remote start does not work if there is no key in the lock

Just curious do you know what the look circle thing under the car is for? Is that a tow hook

What is the tool your using called that’s pretty handy

How did you get anti lag on yours?

Turns out the cylinder im having a misfire on has a broken connector, ill see if thats the issue ,cheers man!

Sick man love it

Hey what's up how much do you charge to program a clock spring