S09 Engineering
S09 Engineering
  • 15
  • 145 242

Відео

Motorcycle Speedometer Mounting Bracket | Honda CB500F Cafe Racer Build #6
Переглядів 4,1 тис.3 роки тому
Motorcycle Speedometer Mounting Bracket | Honda CB500F Cafe Racer Build Parts are available now at choicecitymoto.com/products/cb500f-speedometer-mounting-bracket With the Honda CB500F round headlight conversion finished, it's time to address the speedometer mount. Since I removed the stock headlight assembly, I needed to figure out a new way to mount the speedometer. I did not want to mess up ...
Harley Daymaker Headlight Install | Harley Davidson Sportster
Переглядів 2,3 тис.3 роки тому
Harley Daymaker Headlight Install | Harley Davidson Sportster Check out choicecitymoto.com/ for more information. Instagram: choicecitymoto This video shows how to install Harley daymaker headlight. The daymaker headlight installation is very easy. The daymaker led headlight for Harley Davidson is a big improvement over the stock headlight. The motorcycle in the video is a Harley...
LED Motorcycle Headlight Assembly | Honda Cb500f Cafe Racer Build #5
Переглядів 5 тис.4 роки тому
Led Motorcycle Headlight Assembly | 5.75" LED Motorcycle Headlight Check out Choice City Moto (choicecitymoto.com/) for more information. Instagram: choicecitymoto If you like the increasingly popular minimalistic rugged look, this modern motorcycle headlight mount is for you! It has been custom designed for easy installation with a low profile design that allows for tighter moun...
Custom Motorcycle Headlight Housing Install | Honda Cb500f Cafe Racer Build #4
Переглядів 14 тис.4 роки тому
Custom Motorcycle Headlight Housing Install | Honda Cb500f Cafe Racer Build #4 Back in January of 2019 I purchased this 2013 CB500F from a Copart auction. It was stolen and recovered. Due to this, it had two different coats of spray paint on it and overspray everywhere. For this build I wanted to use a custom led motorcycle headlight. The CB500F headlight conversion was done using custom design...
Custom Motorcycle Headlight Housing | Honda Cb500f Cafe Racer Build #3
Переглядів 8 тис.4 роки тому
Custom Motorcycle Headlight Housing | Honda Cb500f Cafe Racer Build #3 Back in January of 2019, I purchased this 2013 CB500F from a Copart auction. It was stolen and recovered. Due to this, it had two different coats of spray paint on it and overspray everywhere. For this build, I wanted to use a custom led motorcycle headlight. The CB500F headlight conversion was done using custom-designed hou...
Remove Spray Paint From Motorcycle Plastics | Honda Cb500f Cafe Racer Build #2
Переглядів 21 тис.4 роки тому
Remove Spray Paint From Motorcycle Plastics | Honda Cb500f Cafe Racer Build #2 Removing spray paint can be easy with the right tools. In this video, I will show you how to remove spray paint from motorcycle fairings using xylene. Xylene or xylol is an effective solvent to remove spray paint. This method can be used on anything, even your car. Back in January of 2019, I purchased this 2013 CB500...
Bridgestone Scrambler Ax41s | Honda Cb500f Cafe Racer Build #1
Переглядів 12 тис.4 роки тому
Bridgestone Scrambler Ax41s | Honda Cb500f Cafe Racer Build #1 Back in January of 2019, I purchased this 2013 CB500F from a Copart auction. It was stolen and recovered. Due to this, it had two different coats of spray paint on it and overspray everywhere. For this build, I wanted to put some more aggressive tires on it. The Bridgestone Scrambler ax41s tires are the perfect compromise between th...
Bonded Title Motorcycle | 6 Steps and Definition
Переглядів 18 тис.4 роки тому
Bonded title definition and how to get a title for your motorcycle in 6 steps. I purchased a motorcycle at auction and didn't receive a title. The bonded title process was not difficult, just a little confusing and time-consuming. I was able to get a clean title without any issues. This video is specifically covering how to get a bonded title in Colorado. VIN inspection link - www.colorado.gov/...
Supertrapp Exhaust on Honda Nighthawk 650
Переглядів 10 тис.5 років тому
Supertrapp Exhaust on Honda Nighthawk 650 Here is a good example of how much better your motorcycle can sound by installing a full system motorcycle exhaust. The motorcycle is a 1984 Honda CB650SC Nighthawk. The exhaust is a Supertrapp cb650 4-into-1 exhaust system I picked up off of Craigslist for free! It sounds much better compared to the stock exhaust system. Thanks for watching the S09 Eng...
Ninja 300 preload adjusters alternative - using clip-ons or other aftermarket handlebars
Переглядів 1,7 тис.5 років тому
Ninja 300 Preload Adjusters Alternative I made fork caps for my Ninja 300 for use with my aftermarket handlebars. These cover up the top of the forks and gives the bike a clean look. This is a perfect solution when using clip-ons or dirt bike bars, as I have. Files can be downloaded from the link below. www.thingiverse.com/thing:3793905 Thanks for watching the S09 Engineering channel. FOLLOW ME...
Dirt Bike Handlebars On Street Bike - Ninja 300 Handlebar Replacement
Переглядів 23 тис.5 років тому
Dirt Bike Handlebars On Street Bike - Ninja 300 Handlebar Replacement Ninja 300 stunt bike build, installing Pro Caken (similar to Pro Taper EVO Adventure) dirt bike handlebars on sportbike (Ninja 300). It's relatively easy if you do not mind modifying your motorcycle. The only parts you will need are supplied in the kit (link below). I did replace the M12 bolts with 40mm long bolts for this pa...
Motorcycle handlebar replacement - Cheap dirt bike handlebar kit review
Переглядів 15 тис.5 років тому
Motorcycle Handlebar Replacement - Cheap dirt bike handlebar kit review Pro Caken handlebars vs. Pro Taper EVO Handlebars (Adventure) This inexpensive handlebar kit available on Amazon is perfect for a budget stunt bike build. This kit can be used to replace your clip-on handlebars. The kit includes a 28mm fat handlebar, dirt bike handlebar risers, pad, and grips. Thanks for watching the S09 En...

КОМЕНТАРІ

  • @GloBoyE
    @GloBoyE 12 днів тому

    does anyone know if you have to actually wait for the old title holder or holders to reply and sign the letter you provided ? or is it the a waiting system for the state ?

    • @S09Engineering
      @S09Engineering 11 днів тому

      The old title holder does not need to respond. If you wait a few weeks and they don't respond, you can move on to the next step.

  • @JamesStokell
    @JamesStokell 12 днів тому

    What grips are these? Cheers

  • @nigelcaudill451
    @nigelcaudill451 24 дні тому

    Thanks! Just got my sportier bars in for my (adventure) bike. Getting my head in the game before I dig in!

  • @ggg-fv9zz
    @ggg-fv9zz Місяць тому

    Can you request that the previous owner file to get a duplicate title when you send to them return receipt requested and save all the expenses and hassle?

  • @OEFarredondo
    @OEFarredondo 4 місяці тому

    Step one: Put your other bikes vin and license plate on it... Step 2: dont ever stop for no red n blue lights.

  • @CutestMaximus
    @CutestMaximus 4 місяці тому

    My bike was stolen and the thieves spray painted it really poorly, so I'm thankful you made a video that'll help me get my bike somewhat pretty looking again!

  • @chongtak
    @chongtak 5 місяців тому

    Your headlight is nice, but I think you could consider a tiny windshield above the light because there is an empty space that looks a bit off.

  • @manwithnoname8238
    @manwithnoname8238 5 місяців тому

    Thanks for the explanation and information. I'm following your steps, and so far, so good. Just a correction - it's a 10-day temp tag, not 30. Ride safe, Fellow Coloradoan

  • @musicauthority674
    @musicauthority674 5 місяців тому

    Will this work with a Chinese quad that was originally sold new without a title.

    • @S09Engineering
      @S09Engineering 5 місяців тому

      Sorry, I have no idea.

    • @musicauthority674
      @musicauthority674 5 місяців тому

      ​@@S09Engineering Thank you for your assistance, I live in Washington State. and they passed a law that allows people to ride/drive. quads, four wheelers, and side by sides, on public roads with limitations. I purchased it from a private seller that didn't get a title for it. I guess my next options would be to contact the Chinese manufacturer? and see if it would be possible to get a title from them. or strictly use it for off road use. thanks again.

  • @emilianomartinez4083
    @emilianomartinez4083 6 місяців тому

    About how much does this stuff cost? Got a bike recently and the paint job is honestly really bad on it. Probably a rattle can, but when I looked closer, theres a few small chips and the original paint looks completely untouched!

  • @JM-gn3kf
    @JM-gn3kf 7 місяців тому

    Put my order in for the headlight and mounting bracket 🤘. Did you add fork braces when you removed the front wheel fender? Or just left it as is? Also did you have to take the front wheel off or can you remove fender without doing that?

    • @S09Engineering
      @S09Engineering 7 місяців тому

      Thank you for your order! That must be the one I shipped yesterday. I have not added a fork brace, but that sounds like a good idea I should look into. When I got the bike there was no fender. I bet you do not need to remove the wheel to get the fender off.

    • @JM-gn3kf
      @JM-gn3kf 7 місяців тому

      Yea that must be the one. Already arriving Monday, I'm super happy with the shipping speed. Oh I figured you removed the fender for the looks. I hate how bulky it is​, but so far have had no luck finding a good brace or replacement@@S09Engineering

  • @suicidejocke1
    @suicidejocke1 7 місяців тому

    what if the previous owner is dead? then what happens with the certified mail part?

  • @mrpaulkraus
    @mrpaulkraus 8 місяців тому

    Just bought my first non-title bike in colorado. thanks for breaking the process down. I hope mine goes as smoothly as yours did.

  • @timprimozic8914
    @timprimozic8914 8 місяців тому

    hey hopefully you reply...i just wanna know if this is alcohol, or some kind of special paint removal we don't have this where i am??? thanks if you reply

  • @joshw3539
    @joshw3539 9 місяців тому

    You’ve deterred me at around 5 minutes in 😂…. ✌️

  • @tommyboston1453
    @tommyboston1453 9 місяців тому

    pilot hole?

  • @peterkeig2123
    @peterkeig2123 10 місяців тому

    I just got a,2019 cb 500X ..was thinking how it might look nude..cool

  • @sjasonsmith
    @sjasonsmith 11 місяців тому

    I just picked up a bike in similar condition. I was resigned to it being great except for the paint, but you’ve inspired me to give this a try!

    • @S09Engineering
      @S09Engineering 11 місяців тому

      It's worth a shot. Thanks for the comment 👍

  • @michaelcrosby6071
    @michaelcrosby6071 11 місяців тому

    Or is deceased the previous owner that is

  • @prototype9904
    @prototype9904 11 місяців тому

    Wow, looks great \m/

  • @sicks6six
    @sicks6six 11 місяців тому

    I bought a pair of cheap trail bars for my TL, trail bikes fall over all the time and mine is no exception, the bars bent like a Coke can, Then I remembered the old test for handlebars, you put them in a vice to the depth of the rubber gripand with one hand holding the top you try to bend them, if they bend forget them, I didn't do that test as I already knew they were made from chewing gum, you get what you pay for, next set of bars I bought cost £10 more and comparing the two was like chalk and cheese, the latest bars were made from much thicker alloy, the wall of the tube was double the thickness of the first bendy-bars, the downside was I had to reem out the ends for my brush busters to fit inside the tube, not a hard to do with a step drill, cosmetically to look at the cheap inferior bars were smooth and shiny the good bars were rough finished, both anodized but different when side by side, the cheap ones the coating was just like that on a coke can, shiny, smooth, bright, the good ones were pitted, rough and duller, the good ones are blasted prior to coating and that is the No1 tel tale sign to look out for as cheap bars are not blasted prior to coating and have very smooth shiny finish,if you look closely @ 1:05 you can see the finish I'm talking about, that is not the coating on the bar that is the bars surface after its been treated in a particles coatings finsher (shot blasting to you a me)

  • @RaulMedina-w4i
    @RaulMedina-w4i 11 місяців тому

    Can I cross the border with this title

    • @S09Engineering
      @S09Engineering 11 місяців тому

      I assume you can, but I don't know anything about crossing the border.

  • @vkayysmoto
    @vkayysmoto Рік тому

    😢 my bike was stolen last night. They took it for a joyride brought that shit back and now I have to fork out almost $500 for a new ignition switch and steering wheel lock.

  • @lmnt02
    @lmnt02 Рік тому

    For the love of Pete please step the drill bits next time ‼

  • @JonathanThornton-Wood
    @JonathanThornton-Wood Рік тому

    What kind of pick are you using I have a 2021 sportster iron I need to move before it gets towed cause I lost the key

    • @S09Engineering
      @S09Engineering Рік тому

      It was just a random pick set from Amazon. I could do it with multiple different types. Start with a rake with points on both sides and just wiggle it around in there.

    • @JonathanThornton-Wood
      @JonathanThornton-Wood Рік тому

      Ok thanks

  • @JustAbnegator
    @JustAbnegator Рік тому

    I personally love the CB 500F without the fairings, it really feels like a naked

  • @derrickjohnston7181
    @derrickjohnston7181 Рік тому

    Cool

  • @balunalluri3623
    @balunalluri3623 Рік тому

    Hello sir. Thank you for the information. I have a situation. I live in New Jersey and I bought a motorcycle Royal Enfield 500cc. I bought it from a random guy in Facebook marketplace. He said he got that motorcycle from an estate sale and the owner of the motorcycle is dead. He didn't give title. I have a bill of sale but no title. How can I get title for the motorcycle. If there's a possibility to get a title then I'll do that or else I thinking to return the motorcycle. I'm waiting for your response. Thank you.

    • @S09Engineering
      @S09Engineering Рік тому

      Each state is different. Your DMV should be able to help answer this question as well. I believe a bonded title will work in this situation.

  • @camerondoig3008
    @camerondoig3008 Рік тому

    Do you still have the link??

    • @S09Engineering
      @S09Engineering Рік тому

      This is the closest thing I can find at the moment. MOTOROFF 1-1/8" Motorcycle Handlebars, Universa Dirt Bike Handlebar with Bar Pad Grips Mounts for Raptor250 660 CRF250 CRF450 400EX Banshee 350 etc.Dirt bike Pit bike Pit bike (Black) a.co/d/8cvMNPV

  • @lecoureurdesbois86
    @lecoureurdesbois86 Рік тому

    Anywhere I can get this? Can't find anything online

    • @S09Engineering
      @S09Engineering Рік тому

      It would have to be used. Supertrapp does not make these anymore. Maybe ebay 🤔

  • @RussellFields-uq5gk
    @RussellFields-uq5gk Рік тому

    What about front brake and clutch cable?

    • @S09Engineering
      @S09Engineering Рік тому

      Yes, you will want to put those back on the new handlebars 😆. I assume you want to know if any modifications are needed. Everything fit. I do remember needing to reroute brake line and throttle cables, but no new parts necessary.

  • @jthudson4614
    @jthudson4614 Рік тому

    Is there any changes to this process if the motorcycle was purchased over state lines?

    • @S09Engineering
      @S09Engineering Рік тому

      I don't know for sure. I may find out soon. I found something I like in SD.

  • @fattohead
    @fattohead Рік тому

    Hi, my bike (nc750s) also has a led headlight and I want to change it with a round one but I don't know which values I have to check first before installing a new one. Or is it possible to install any headlight I want? Thanks in advance🙏

    • @S09Engineering
      @S09Engineering Рік тому

      I don't know. If it has an H4 connector, you should be good to change to pretty much anything.

  • @MarshallSmith27
    @MarshallSmith27 Рік тому

    I have a BMW off road motorcycle g650x xchallenge and the previous owner gave it an ugly paint job

  • @kamadazee
    @kamadazee Рік тому

    Just got a nail in my Bridgestone 160/60s and I went to my closet shop and accidentally had them order me stock 150/70s for my Suzuki bandit…. found these and I’m in love with the look and how people are saying it rides. So thank you for the video, good work. And I’m sorry your bike was stolen. At least you got her back and with some beauts of tires..

    • @S09Engineering
      @S09Engineering Рік тому

      Right on! These tires are working well for me.

  • @KyleMurrison
    @KyleMurrison Рік тому

    I’m trying to get a tittle for my 2002 Honda show

  • @cykablyatman5758
    @cykablyatman5758 Рік тому

    Does it matter what size I pick when checking out on the website

    • @S09Engineering
      @S09Engineering Рік тому

      It does matter. You need to pick the diameter that matches your fork tube diameter where the light will mount.

  • @jamesc6363
    @jamesc6363 Рік тому

    Thanks!!

  • @michaeladams9335
    @michaeladams9335 Рік тому

    Use Autoglym Bumper & Trim Gel once all paint is removed from plastics. Will look like new again .

  • @DavidGorobtchouk
    @DavidGorobtchouk Рік тому

    So I looked at the wiring diagrams for a 2019 CB500F and have a 2017 CB500F, and the headlight 100% isnt plug and play

    • @S09Engineering
      @S09Engineering Рік тому

      You are 100% correct. The models with the OEM led headlight are much more difficult to do this mod. The older models have an h4 connector and require zero mods to the wiring.

  • @NinjaNinja-fz3zv
    @NinjaNinja-fz3zv Рік тому

    Ha my Ole bike!

  • @jeffklynch
    @jeffklynch Рік тому

    I have a 2002 SV650S I've been wanting to title. I'd considered the Vermont approach as I didn't realize a bond was affordable. I thought the state wanted to keep twice the value of the vehicle for a few years!

    • @S09Engineering
      @S09Engineering Рік тому

      The bonded title seems like the more legitimate way to do it. A 2002 is plenty old enough to go the Vermont route as well.

  • @Chipbayles
    @Chipbayles Рік тому

    What would happen if they said they wanted it back? I bought an 05 r6 off marketplace went to dmv they told me last title was in Georgia. I live in Kentucky. Clean title. I have bill of sale that’s about it.

    • @S09Engineering
      @S09Engineering Рік тому

      I really don't know. It is old enough to do the Vermont thing.

  • @vortecmacs
    @vortecmacs Рік тому

    These are well shot and edited. You should make a lot more.

    • @S09Engineering
      @S09Engineering Рік тому

      Thank you! I will make more videos sometime. I really do appreciate it 🙏

  • @lonnydupuis3014
    @lonnydupuis3014 Рік тому

    What do I do for old truck no number on motor

    • @S09Engineering
      @S09Engineering Рік тому

      The bonded title is only needed for newer vehicles. There might be a better way.

  • @lonnydupuis3014
    @lonnydupuis3014 Рік тому

    A 1970 Ford F_100

  • @BoxchevyEnt
    @BoxchevyEnt Рік тому

    Got them on my banshee

  • @jakeharr3653
    @jakeharr3653 Рік тому

    What do you do if a bike was traded second hand from the original owner but not knowing if it was stolen would state police be able to size the vehicle and charge you for possession

    • @S09Engineering
      @S09Engineering Рік тому

      I don't really know what is possible. This exact situation happened to me. The bike I was getting a title for was reported stolen, but I had the bill of sale from an auction house. Nothing happened.

  • @Young937phoenix
    @Young937phoenix Рік тому

    You cutting oil next time and it will drill alot easier and the bit won't break.. it got done but that could have been alot easier..

  • @shaun.1kk681
    @shaun.1kk681 Рік тому

    Where can I get these handle bars

    • @S09Engineering
      @S09Engineering Рік тому

      Amazon. I'm pretty sure I talked to you on IG.