Відео

What quick release rings are you running on this rig? Im building this set up and would like those rings

Do you have a link for the base/rings

Are u able to run hollow points?

Can u plz provide names of the optic and optic mount?

1:50 you incorrectly labeled the Holosun. it is not a 512. The 512 is closed 510 is open.

Which would be better for trunk gun/ glovebox / bag / range toy? I’m torn on both I like the 20/20 is more compact but I like the mck is high quality but if you could only choose one for a g45 non mos and I want to use something for a sight eventually at range and practice with a shoulder mount which would be ideal? Plz help me out maybe make a video shooting both comparison of all the details how they feel in use etc plz?!

Saved me 4 hours, thanks

If you remove one of the dividers in the stock it holds a box of 50 22lr shells another nice option

Is this urgi color from the factory?

Do you have a link to the scope n rings

I thought we were getting a comparison to the EOtech

if it’s registered why is the number covered up?🤣🤣🤣🤣

Where can i buy that trilug barrel?

Great video. Is that an 8" ILWT tri-lug barrel with an 8" Lancer handgaurd? What muzzle device do you have on there?

great handguard, need one because the k model maybe blow out my fingers hahahha

I noticed that UTG makes this scope in a 3-9 either with a parallax adjustment or without. I went with parallax. Hope I made a good call!

Thank you , fast , to the point , no bs!

how bad is gas to the face while suppressed?

Great display! New sub, and I hope your channel grows!

Sweet setup and thanks for explaining why you bought the aftermarket parts/accessories you did and why they are better than the stock ones.

Why does the dagger have one less pin hole?

What scope is that?

I have a similar setup except with the Tactical Solutions lightweight barrel. I found I was getting a slight shift in zero every now and then so I went with a Magpul scout mount over the barrel with a red dot. The sight always stays aligned with the barrel and it's a great design 👌 👍

I don't get much gas back to my face on mine? I don't run suppressed yet either.

If a friend wanted this they would need to form 1 the lower then Can attach the upper?

I just put an eotech on my baby girl and my Wolfman coming in next week 😊

I actually love the ddc color on the geisseles especially when it’s paired with a mix of fde and coyote brown

is your barrel an ILWT barrel?

Which suppressor is this?

I dislike you encouraging people to admit that they own an "illegal" firearm. Registration is not the answer. Get a 16 inch barrel or longer and put it on the firearm until the court shoots this bs down. Your video is not helping anyone and just creating sheep.

Easy would not be an adjective I'd ever use for this process. Even if it is the best worst-case decision.

You should provide links to online resources.

Can u just cut the brace flaps off and be compliance

Question I have a gen 3 mpx k and just installed the radian raptor charging handle and I noticed on top of the charging handle it’s scratching right under where it says radian and I noticed when I have a mag in the gun and I pull the charging handle back and release it sometimes it doesn’t close bolt all the way unless I really let it slam or when I rack the radian back with a round in it sometimes charging the handle the bolt will get stuck if I’m not using force I never experienced any of these problems with the stock CH I Use the new sig branded thrill mags as well but the radian just seems I have to pull back harder and release harder for it to work properly using the bolt release with radian installed it closes every-time no problem was hoping you might have some feed back and I have no lifter block installed on the radian CH either as the new ones say they don’t come with or are not needed

I wish you had links and website images instead of showing the same gun and blabbing for 4 minutes. Thanks though

ANYTHING you say or do WILL be used against you in the court of law

Thanks man.

What is the total length (stock fully extended, no suppressor)?

After everything is approved can I put a normal butt stock on the firearm?

Would this work with the integral suppressor?

Nice review! But 530 model missing :)

Need to rally the troops and get these ATF DOJ clowns shut down! This is stepping!

What picture of the firearm did you submit?

That has nothing to do with it if you think that has something to do with it you got a lot to learn pal it's about control it has nothing to do with the brace or the gun it's about control making you pay for something and having you in a database which they already do if you got a serial number on the side of your gun than you're already in a registry

And do you realize they're making you register a safety device yeah that's supposed to help you shoot safer so they're making you register and restricting a safety

It is against federal law to have a firearms registry

How to admit you are a cuckold....😂

CAN YOU ALSO PUT A STOCK ? ONCE YOU GET APPOVED

Great video - fast to the point.

wtf is a CLEO letter?