Відео

Roof Semen

Thank you for your help

I have to inspect tomorrow but I think a couple of mine just popped up or ripped from hurricane Milton… we had the roofing company leave behind about 4 stacks of shingles… so I should be good to go as soon as the sun comes up… and they left the tar too…

Thank you so much for making this detailed video, you did such a good job. We have a leak on our porch roof and I was so stressed out about it but this video calmed me right down about it! I especially appreciate you reminding people to give themselves time so they aren't stressed and rushing. Thanks again!

Thank you for using intelligible English! Great video - looks like the dish I just took off my roof! Great demo - A+!!

Thank you for your video. It was helpful!

Wonderful video? Do you have a video of how to replace shingles in a valley after replacing damaged plywood?

My garage doors have big natural cracks! Been saving money without even knowing lol.

Awesome video!

Thanks for the video

Thanks keep up the good work ty

Learned a lot. Thank you.

Thanks!

🎉🎉🎉🎉🎉

I installed 5.5"/R20 of open cell spray for an unventilated attic under asphalt shingles in 2014 and have had ZERO issues. An unventilated attic with spray foam is "god's" gift to air conditioning in a hot, humid climate. PS I have friends that have had the same type attic installation 18 years with ZERO issues.

This is a great video! If I chose to have a professional go out and do it instead, what's a ballpark this size?

May we hire you? Youre awesome for providing the details. Saving roofs Thank you

Great tips, thank you!

What's the song you got playing @ 8:00? I found the song "New York Bagel" from the lyrics but it sounds different

The problem now is no air in no air out, is apparently causing the wood to rot in the roof.

I'm scared of heights. But I'm also cheap. Guess I'll be getting up on the roof....

Thanks, very helpful this was perfect for me repairing my garage roof

If you use silicone paint on the wood directly make sure the first coat dries then apply second coat and make sure second coat dries . Note that silicone paint applied over shingle roofs ( always 2 coats ) will usually last 10 to 15 years . Read product label on cans . However , most silicone paint is covered by twenty years warranty on painted shingles . If it is painted on wood roof deck with underlayment and shingles over it , who knows how long it will last . Reference my comment on roof fan leak .

The roof fan should be nailed directly onto the roof wood not nailed onto shingles . You can nail this 3 ways. : 1 ) Nail the fan directly onto the roof . 2 ) Roll silicone paint on the roof with 2 coats - make sure the 1st coat is dry before applying the 2nd coat . Nail the roof fan onto the roof over the silicone painted area .Make sure the the silicone is painted 3 inches past the roof fan flashing and use neoprene washer shank nails on the flashing . 3 ) Put synthetic underlayment on the roof and nail underlayment and cut the circle out for fan exhaust hole . Nail neoprene washer shank nails into the roof fan flange . Make sure you put another synthetic underlayment over the fan flange that is exposed by cutting a O out of it with a slit at the bottom on the downward slope ( straight cut from the fan tunnel toward the roof edge so water will flow to the downward slope . This slit should be 1 / 4 to 1 / 2 inch wide to let water flow downward to roofs edge . Make sure their is underlayment the entirel length of the slit or you will have a roof leak . Lay synthetic underlayment on rest of exposed wood and nail it down . Make sure you are running underlayment up the roof to the highest part of the roof . Put next underlayment 3 inches over the previous underlayment . The next row of underlayment should always be tucked under the next underlayment 3 inches . Nail NEW shingles onto roof . REMEMBER YOU ARE NAILING NEW SHINGLES FROM EDGE OF ROOF TO HIGHEST POINT OF THE ROOF . Good luck .

The first vent was not put on right . See that a leak occurred on the downslope of the roof where a nail rusted out due to improper placement of the nail .

I noticed you were nailing directly above the cutout on every shingle. I thought this is the weak point. Preferably a 6-nail pattern sh/be used; namely one at each end and two on either side of the cutout, instead of one directly above it. Great tips, thank you

Wondering what to do with my furnace and water heater drafting air from my attic ? How can I use a solar attic fan without drafting my cooled air from my living space ?

I'd work circles around this guy

If you have attack access. Drill a hole and saw a long the stud and stud to stud around your work area. Go up and remove the blank. Strip away 3 layers above and below the blank and 1 shingle to the sides. Cut a 2×4 nailer and install it along each stud Install a cross support between studs were boards meet to stomp any cushion. Cut your new board. Install. Replace water barrier 1 shingle deep top and bottom and half shingle wide side to side. Install new shingles. It's simple, easy and quickly done in this way.

Back off with the camera shot.

You should install cross support were the plywood meets between studs and a nailer along the stud were the wood meets wood to. This stops all cushion movement.

Can you do a video on safety for working steep roofs; from start on the ground to installation of roof hooks etc?

So very well done. Thank you.

This is an awesome and very informative video. Your skill level is obvious, and the detail is acceptional. TY

Can I install the gable fan backwards and draw air in?

I am about to do a home construction project - and will do spray foam insulation BUT with a metal roof.

I had a tree fall on my roof on removing the shingles I have no felt underneath the shingles what should I do I only planned on repairing the damaged part of the roof

Good stuff brotha, thanks for the video.

If that corner sticks out like that it can catch water which would run under the shingle and into the roof.

The nails should never be exposed. You never put nails at the exposed bottom.

Great video, very informative. Thank you very much!

I've been having a hard time finding a contractor that is willing to install a roof vent cap to connect to the 6 inch range hood duct already installed in the attic. Just found a sheet metal company that gave me a quote. However, the quote referenced a "roof jack". I've never heard of it so research lead me to your video. May I ask, what the difference is between a roof jack and the more low profile vent caps. Does the roof jack prevent birds, critters, or insects from getting inside?

I can do this. ✊Thanks for the video.

LOVE this video. Looking forward to checking them all out! Not suggesting there is fault in the video when i say -> screws are great for plywood. Ive found better at correcting for uneven studs/ joists. Firms up entire roof, imo in a good way but i could see how maybe faint wiggle from nails was needed to not crack interor drywall. Also holds well to beeswax or tar, and easy to dip and zip. easy to push below surface and fill, and still easy to remove, vs covering nails.

Great tip, just what I needed right now!

Hi! What roofing caulk would you recommend for using in Houston? Is there any product on the market that won't dry out, crack and shrivel too quickly on a hot Texas asphalt shingle roof? I am looking at resealing vent flashing, their exposed nails, as well as securing down the parameter of roof edges to minimize first course shingles blow off from strong winds. Your expertise is greatly appreciated!

Told us the Nail length (thank you). Excellent orientation of the camera. Clear steps. You are a great teacher😊

11:17 how to install H clips on the top when you have them on the bottom of a board in the middle? I didn’t want to rip all the boards off above too…

Great video. This definitely details the process well. Thank you.

So how do you remove shingles that were installed on top of Ice & Water shield. I've tried to remove some shingles and the top half of each shingle is in contact with the roof which has I&W shield, and as I'm sure you are aware the shingle is now bonded like its grown to the I&W. If you know of a technique to remove the shingle from the I&W I will be eternally grateful. Thanks and be safe up there.