Відео

i’ve been watching a lot of 3d printing vids and this one was recommended to me by the algorithm. It looks really cool, but i found myself having to look at your channel vids to try and see if there was a video explaining what exactly this unit is doing / why its unique. might be helpful to include a quick short blurb about what it is at the beginning of each vid to help segway new potential subscribers more seamlessly into your content :) keep up the great work!

Looking forward to the inclusion of the Nitehawk SB as I am planning a build of Misschanger using that toolhead board. The great support of your project is greatly appreciated.

21:50-21:55 for the moment that porky pig enters the overdub studio. Ahabadehabadeehabaduuuuuuhhhh that's misschanger!! Haha But seriously this product is turning out to be amazing dude, great work!! 👏🏻

Amazing!!!!

That's great

Thanks you!

I print PETG and ABS on my 2.4 by only decreasing bed/nozzle temp by 10-20C. No other changes. No issues with PETG with chamber temps. I used to think like you did and had exhaust vent air but it does not matter.

What's the effective build volume when the dock's installed?

If I understand correctly, your trap door mod replaces the stock removable air duct and exhaust slider with something that's a little faster and easier to use? Do you find that in exhaust mode, it provides sufficient cooling to the chamber to print PLA without removing panels?

What is the thickness of the top panel you installed? The PCBWay is listed as 3mm. Is it acrylic as well or PC? Does it feel solid or sag any? You may want to cannibalize the nevermore micro and use the ellis bed fan mod. I did the same as you for a few weeks after installing a stealthmax (back panel though; I have a second top-mount printed that I haven't installed). The ellis bed fan setup circulates noticeably better. So well, in fact, you have to have a custom ramp-up time based on bed temp so you don't warp your bed.

I like how you handled the umbilical cables. Can you release the files for the mounts that you have for the cables coming up from the base and for the retractable things that are holding them up from above?

I wonder if I could use this without a voron tap or is it much better with

I have been waiting for someone to do this. I always thought it was stupid that the gantry has to go all the way to the top just to swap toolheads.

It depends on the geometry. If you were to print even two benchies at the same time you wuold see improvment in layer adhesion and overall quality of layer cooling.

Love your work and your transparency on the projects you do !!

Like I havent even seen a single statement of what this is or why it is

This looks cool where is the guide

this 3d printer looks expensive?

какая гигантская батарея отопления, мужик, ты на северном полюсе живешь?

Shame input shaper is effected horribly :(

Como posso conectar os cordões umbilicais à placa Octopus Pro v1.1? Qual acessório devo usar? Porque minha placa controladora tem apenas uma conexão Canbus. Meu projeto terá 6 ferramentas, estou preso nisso. Eu agradeceria se você pudesse explicar ou recomendar algum brancher/switch para conectar todos esses cabos à placa. Eu sou um iniciante.

Thanks! What is this sort of plyer you use as a vise to pressfit the magnets ? It looks very convenient.

So whats the benefit of this over stealthchsnger? Everything ive seen/read indicates Stealth Changer is better. More tollheads, better IS, more compact design/less bulky, more successful users, better documentstion, etc. Like i get wanting to develope an alternative, but whats the point if its the reheaded stepchild of stealthchanger?

Gtfooooooo impressive

Great work keep it up.

Great work!!

does this tool changer require you to have canbus or can it be setup without one?

I have no clue why UA-cam Short decided to make the video look like that 😅

This is so damn cool what the hell man 😭 amazing work

clean !, well done mate !

Great project. This could end up being a better solution than the Prusa XL.

forgive me for being slow... the tool changer is at the bottom of the printer, so when tool changing with a half printed model its gonna smack it... why not have the tool changer at the top?

🎉

Is there a documented way to add something like the ercf also? Imagine having it swap colors on a multi color print while there is always a tool head actually printing? (Eg. 4 colors on 2 tool heads.) Best of both worlds

that's fantastic! great job!

Is this compatible with Rama lama idlers? And do you have a video explaining the latch mechanism that locks the toolhead support structure in place?

Glad to hear it is in beta. Can't wait to see what's to come

Awesome. Very interesting 😎. Are you able to upload a vid when it's in action/printing? An STL that uses multi color filaments perhaps?

Good work dude 🤩 I'm designing project on my own and I know how time consuming they can be, especially about creating manual heh I really appreciate your work ❤️ I'm waiting for more content

Thanks for doing these videos and for adding more options to the Voron ecosystem

You doing a great job. Can't wait to rewire my 2.4 for nitehawk-SB (will get to remove so many wires!)

Where can I get the bom for V1.0 I didn't find it thanks

Do I understand correctly that this is the key feature that differs MissChanger from StealthChanger? Or is there more?

Thanks!

Brilliant! Looking forward to the next one 😊

This is excellent! Thank you for all your effort in this project! 😎

hey there, this is from PCBWay. Currently, we'd like to see if our custom services can contribute to future MissChanger work. Feel free to circle back so we can talk.

can i install this if i have AWD?

Super cool I can’t wait to see more.

Could you make a video about wiring the stealth burners to the XLR connectors? Great Job