Відео

HNSR-ZCPD

Thanks! Going to take care of this, this weekend, thanks to your video. This saved me quite a bit.

not clear enough. I don’t understand what you said the problem is. So i can’t correct my problem.

Thank you sir. It works on my dead scooter battery. Godbless

I took both doorknobs off, the inside of the latch mechanism fell out. Nothing left but the latch that won’t budge, so I can’t open my front door. HELP!

I just bought one of the red ones with that same sticker on it from amazon a few weeks ago. The offshore people must have gotten tired of people whining about these things being junk out of the box because the one I bought will wobble for a week with no mods. The pin and socket are corrected for proper functions. Now I'm going to find your laser video. Sounds cool!

this shit does not work

Got my power steering back, Thanks for the great video, very helpful!

Will work just fine..coscos the best😊

cool bro

It worked perfect ! Thank you 🙏

Finally, someone who freezes their video and shows us a close up! Thank You!!!

I have about 300 NEW LG and Panasonics here and about 150 used of the same and had just thrown out like 9 of them for being ZERO responces. Damn to late now. But good to know in the futurte. I know with all these batteries i should not worry about 9 or so lost, But every one is one more than i had before when it was dead zero.

sacrifice one battery and pull the top button off to illustrate?

Unbelievable, brand new, stuck in, took it back out ogf the door and the entire latching assembly fell apart. What a pos

I have an issue where when i unlock the door with the key, the key turns all the way (almost complete circle) and when this happens it mis-aligns the interior lock knob. Is this something wrong with the latch itself that I could replace just that, or something internal in the lock mechanism?

The harbor freight balancer is a piece of junk without this video modification. Can't believe they manufacture and sell it as it is.

I'm about to buy one exactly like this one on the video, please let me know if it's any good. Thanks!

You are wrong about the drilling out the hole. Mine was bought about the same time as yours and it was made of steel and if you don’t get the hole drilled out in the first time you probably won’t get any farther than that because you have hardened the metal and you will just burn up the drill bits , I know for sure because it happened to me so you have to change the pin on the shaft And it can’t be a point , it has to rounded over because the spot you tried to drill was almost flat.

Thanks so much mate

Camera was too far away to see really what was going on

This fixed the issue on my '05 Chrysler Sebring. Thanks a lot!

Torch tip cleaners are better

Thanks, he talks so slow though, play at 2x speed 😂

Thanks! I've been mounting my own tires for years, but never had a way to balance them. I just ordered one and I am going to use the drill only method for modification.

what if you don't own a soldering gun? any other way?

you could also just grind off a chain link and add your own master link...most snowblower drives use standard #40 chain

If you have gone as far as doing the mod, nothing has to be said about how to use the balancer. The ones that cant make the mod will for sure not even buy the balancer in first case 🤣👍🏼😇. Good job and great video. Im a very technical dude age 55 and it bothers me that I havnt even thought about a laser. I might be born in the wrong era. Laser is to new to me 😁.

I JUST DID THAT- IT WORKED PERFECTLY! thanks a ton!

Is there a belt or anything on this if my spin cycle won’t work? It drains but clothes are still drenched, thank you!

My doorknob wont lock 🔒

Nice content! do you have any idea where to buy the bushings? I've had zero luck finding the ones for the clutch above where you are working, mine are wallowed out and basically gone, still works, the ole dog, but lots of play!! My part numbers 50705 and 50700!

I used a 1/4 ratchet with a 10mm socket to remove and put back on the long tilt bolt.

Thank you so much. That job would of cost over $1000. You showed exactly how it's done. It help me fix my car and I am sured it was useful for everyone else. I had to do the job twice because the first steering assit motor I ordered was defected. To anyone watching if you change the motor and your steering wheel is stiff then your motor is likely defected.

Nothing happen

Nice video too you gave motor size

This worked like a charm. I just wanted to say thank you!!!

I take it you last video with the ballencer didnt work if your still trying to improve on it. Or have I misunderstood.

Hi sir! Thank you for sharing. I am actually doing this job now. I am stuck at the pinch bolt. My wrench is turning left ,but it doesn't seem that the bolt is loosening. Did it feel like it was loosening when you did it. The motor is going lower but screw doesn't seem to be loosening. Any suggestions please?

Thank you so much! Question: Did you have to reprogram like the dealer requires? Or is that to take your money 💰!!???

so what's the verdict? Do you still recommend it? Any con?

If you widen the hole....am I right in thinking the is not way of knowing if the tip is in the center of the pivot point. Has anybody tried to use the balance rig as delivered. I mean does it really matter if its sitting on the shoulder.....I agree it dont sound right......but maybe its accurate enough.

Thanks brother Vinny. Just did this on a standalone version, it worked well.. all these companies using cheap components really sux.

I love this👍but working underneath the ladder will give you bad luck?

You are the only person who shows me to punch the core out, Thanks. The only difference is that after I had widened the hole I put it in a cordless drill as a drill bit and grinding on the pin together until the point touched the bottom

You had lined up the RED DOT with the air valve you would have got it balanced. The RED DOT is the Highest part of the tire and the the YELLOW DOT is the heaviest part of the tire. If there is both dots on your tire,.. the RED DOT is used over the YELLOW DOT every time. it seems the shop that installed your wheels on the rims did not do it do that when they were installed.

was this due to a power steering fault. Struggling with this now we replaced the torque sensor same fault. Also runing a tire pressure sensor fault and seemed to see these could cause other faults sounds weird but kinda lost im about to get a whole replacment used colum like you did...

what are the connectors in the dorman 14151 master cylinder bleeder kit for? like the one way connectors?

thx, do the video on configuring the external router, im assuming the modem is in some kind of gateway only mode

exactly what i needed to know