Відео

The wall mount for the AMS light?

If you are just starting I’ll recommend to go for ELRS instead of crossfire. Crossfire is an excellent radio protocol but drones like the air65 are only made in ELRS because it’s open source and more economical. If you like the shape of the tango 2 look for the jumper bumblebee, I found it to be the same feeling, it’s a new ELRS and much cheaper. For googles look at skyzone goggles. They have the whole range for your pocket. Chose the one fits you better. Cobra X is excellent entry level. O4 o Pro for the high end.

Thanks for watching! I’m glad it helped

Thanks!

Thanks 👍

There are many. I will recommend you to get a 3.5” like cinebee 35 or the GEPRC cinelog35.

I think both have their pros and cons. 1s is more for indoor flying, while 2s is great for tighter outdoor spots, where bigger drone may be overkill or dangerous to fly. I'm kind of getting in to 2s and I think I will be flying it outdoors a lot coming summer season.

this drone does not feel heavy at all, it feels light and nimble to fly, but the prop wash and wobble is caused by something else. hard to say what though...

@TrickyFPV420 So Whats the weight of this drone and Whats the size of the props? It would be easy to compare to beta 75 pro, 85 pro and mobula 8.. And this is whoops. This one should be a lot lighter then a whoop. To make any sense. If the construction have no purpose, then its difficult to understand. I would like to know, why is it made like it is made, Whats the purpose of it. There must be some kind of explonation of its creation. A small drone buy it, is not enough. As a comparison, take the hummingbird 3,1rs. Its a racing whoop, pure and simple. But what is this. Is it a SUV, but in the quad world? Shiny and attracts attention, but cant drive in the woods. I must have one on the wall beside the Picasso painting...?

@ its a 2s whoop for freestyle and cruising around your backyard fir beginner pilots, for people who are not so detail focused on their drones as you and likely will not build a drone themselves as they are not as technical as you. This is clearly not for you and that’s ok 😉

@@TrickyFPV420 Ok, thank you for the explonation. Maybe im more technical interested than the majority. Or my money just come easy..

That should doable. Just not with this program. You will a program that can write directly to the video buffer. That should be pretty simple but I don’t know what CLI program does that. Sorry.

Good question. I think it will be too stiff. Even if possible I think a strap of this filament will break with time. Test fits regular 95A or even better 98A TPU

@NordFPV Appreciate the response. Cheers!

Definitely does!

I gave this feedback directly to GEPRC and they said they liked the idea and they will release the version without VTX after CNY.

After using it for a few months also became aware of the fan, it’s loud, but it’s not loud enough for me to stop using the PSU. I agree it’s a negative feature in the unit.

The review was done with the freestyle version.

I think you should give micros an other chance. Lately with new products coming out, they have become really good and fun to fly! I do agree though that the usb contact sticking out in this design was a bit lazy of GEPRC.. Especially when there is more than enough space to put some rubber standoffs in there tu push it up slightly and make it much more secure.

@@TrickyFPV420 Haha I hate micro usb not micro drones :)

@ haha, well give micro usb an other chance as well! 😅

That’s a hard question. You need to read specifications and make sure you are choosing the right parts that work with each other. When people can’t do this or don’t have the netto do the full research they buy BNF (bind and fly) which are drones already build by a manufacturer who has chosen all the parts for you. Otherwise you copy someone else’s model.

Hakko fx -888D

Hello. There are many videos on this. I even have a couple of videos in my UA-cam channel About binding ELRS. Please go and watch one of those.

So binding with elrs is same on all tx radios ??

@@TheLibin7 Kind of, yes.

Thanks for the tip for the chart!

You learn something new every day!

Mark5. It’s one of the best BNF drones I’ve ever flown.

@@NordFPV thank you. i'm really inclined to get this

Thanks for the visit

It's quite air tighten, and you have place for som disecant, so it will do a decent job storing a roll, but it's not like the Eibos that has a mode to hold the humidity at some specific value.

yes, it's amazing there are still ways to shave a few grams here and there of the air65. The antenna is another way, and the power cable is another one.

What did you buy?

Thanks!. I got a mount form thingiverse. I didn't have to adapt it or anything. The sense is a clip to the camera.

I use Betaflight rates RC RATE. RATE. RC EXPO R. 1,2 0,75 0 P. 1,2 0,75 0 Y. 1,2 0,75 0

@NordFPV thank you very much! Happy flying! 😉👍

The original mark5 from the GEPRC website. Look under support.

It’s not as it is today, but I’m sure they will get an upgrade kit for that front cage. It shouldn’t be that difficult to adapt. But if you are looking for a good cinewhoop with O4 have a look at GEPRC 3” O4 whoop.

@@NordFPV yeah I saw that one too, I would like to keep it 250gr, I hope they release a 2" 2.5". thank you

Tattu 300 maj BT2.0 all day long!

@NordFPV thanks dude!!

They are softer than radiomaster gimbals.

Thank you for your kind words!

I haven’t tried but I will suspect they are not without some small modifications to the AG01. I know for sure the cables has a different order.

What are we talking about?

​@NordFPV the price of the tpu you use ahah

@@jasonbelanger6192 I'm not sure I understand your comment. I buy this TPU in bulk and it cost me between 12-15 USD.

Yes, I agree with you. Unfortunately it break quiet easy compared to 95A

I'm agreeing with you 100%

I'll probably do some videos building with O4 yes, but most frames will require new parts, upgrade kits to fit the big camera of the O4. That means not every frame will be adaptable to O4, and there's a chance that you better wait and build from scratch with a frame designed for the O4 than just try to upgrade the one you have.

Sorry you don’t like my music taste 😂. I recommend to mute it and use captions.

You can barely hear it and it's just standard non-distracting background music. I mainly listen to death metal, but I certainly don't want death metal blasted in the background of UA-cam videos

It’s good for pinchers. And with a bit of effort you can find stick end that could make it even better.

Noted, thank you

Thank you. I tried to buy this TPU when it launched but it was sold out pretty quickly. I had to wait until just literal week or so ago, and I’ve been working on this video since then.

There are several techniques to do multicolor prints, but none as easy as to do multicolor with an AMS. Idex printer or multi head printers will be the best choice but obviously that has a steep price.

@ let’s see if new Flashforge AD5X will be able to print multicolor TPU as advertised

In the AD5X you still have quite some distance from the motors pushing the filament on the AFS up to the print head. Despite you can achieve decent prints with a kind of bowden tube configuration, some issues will be expected from my side in this system. Only time will tell.

No

@@NordFPV owh, thanks

You can print only accessories. The main parts of the drone as the frame can’t be printed. They need to be in carbon fiber.