* REWA Academy Training Book PRE-SALE of iPhone motherboard repair available now! Do not lose the opportunity to get limited systematic REWA training treasure (1000 limited stock for pre-sale). > bit.ly/31I5Nks
Its not a fix or any help... Its a hack to get around apples locking garbage.. no one should have to go to these lenghs to replace a dam battery.. this is getting out of hand... why do people buy these products for apple to do this to them?
Easier to jailbreak then go in Filza and in Preferences just change the serial number to the new one that’s printed on back of the battery..worked for me
Hi Rewa, your videos are gorgeous, you always find solutions to solve problems. I have been following you for a long time, I am also a subscriber and many of your videos have solved some battery problems like this. I would like to know where to find the batteries without the connectors and those stickers to reset the battery. I thank you for the answer.
@@Hallal-Almaty are you sure that works to restore health? I have the JC v1s programmer and that can’t update the battery health. The software shows its written but when I install the battery in the iphone it shows the same.
Why you didn't show us the battery health after replacing? It stays the same as before replacement.so if you have a battery with 75% max charge it will be the same after replacement
You'll get better or worse health depend on cell you bought. It wont or will stay the same, since BMS does not affect BH (at least in this case because manufacturer's BMS has higher quality than 3rd party one). It just contains Apple encription, thus you'll need them to not get the annoying message.
I have the same issue ( iphone xr). I replaced bms and reprogrammed. The battery health that phone shows is still 86% ( as it was before replacement) and the software on PC and programmer shows 100% ( as I typed in). Do you maybe know how to fix it?
Hi! Thanks for posting this super informative video. Can you tell us why it's necessary to use this odd little spot-welder? Could the battery contacts not simply be soldered into place?
They can, although solder can snap when you fold the battery board back into place. Using the original nickel sheets means you can bend it without the chance of any faulty connections.
No, We cannot use reprogramming tool to copy the credential of original iPhone battery. Because, Apple use EEPROM in battery circuit chip, which ties the part to the iPhone.
I don't understand why you need to activate the battery. When you plug the new battery into the iphone, shouldn't it start charging right away and accept it as a genuine battery?
Yes, 2 BMS on the battery of iPhone XS Max could be transferred together. But the flex cable of 2 BMS should be more careful about it during the transfer, avoiding to damage it.
Pro tips. When you bought a new iphone if your battery health goes down to around 89 below just buy a new battery and keep the original battery and when the time comes if you want to upgrade then put back the old battery and sell it still good battery health 😂 sorry for my bad english
Yes, you need board or supply to activate battry and programmer to erase old data and program new 0 cyclus. On iphone 11 and above you need small board too which remains with the battry. Here it is not shown that.
I have A Request video to you Please A Don't ignore. "Make a short video about iPhone xs battery vs iPhone 11 battery" (only size Comparison) Or, Otherwise please reply me in comment. What I can use ip11 battery in my iPhone XS. I want to know that. Let me know that bro please A Love from Bangladesh❤️🇧🇩
Great sir ... We already use this technique in Pakistan alit when we dont find any phone's battery thats the best solution... I always learn from ur videos Love from Pakistan
Hello dear. I loved your all videos, you make it very good. And I have question refer to the battery important message. My question if I lose the original battery of the iPhone and then it is show up with the message"importanct battery message" so how can we solve this problem?
Why do you have to 'Activate' the battery? I'm currently using a replacement official iPhone battery, could I just swap the battery management board and be done or do I have to activate it as well?
After reprogramming it I plugged in the battery to the phone to see if everything works fine. The battery capacity is still the same (86% in my case) so my programmer didn't work. I tried reprogramming 3 more times. Nothing has changed. Software and programmer shows battery health 100% but after plugging into phone (iphone xr) it shows 86. Why is that? How do I fix it? I would appreciate every help.
Could you give me advice? When I change board on battery, activated it, set cycles on 1 and set battery on 100% i got issue with battery capacity in mobile. My XS Max show me battery condition only at 78% but when i put battery on quanli iCopy plus, it show 100%. Could you give me an advice what iam doing wrong? Thanks
I never changed battery on my iPhone 12, yet im recieving this error unknown part battery and the phone doesnt charge even after connected to charging port for hours
REWQ TECHNOLOGY great job I have one doubt I have 2019 model MacBook (trutone display) ufortnatly Display is Brocken then I change display but keyboard backlight is not working I try another display but same condition. I put old (Brocken display) DISAPLY keyboard backlight its working fine could you please tell me solution
Hi, is it still showing your old battery percentage? (I’m told that after doing this, the phone gotta be charged a couple of times until the battery health changes)
@@HiItsK Today i have removed this old battery(replaced original with new one) and this is third battery, it is not good idea to do this! Trust me! And yes It showed old battery percentage...
@@Mirandess1 then, would you recommend me to take it to a Genius Bar to replace the battery? I haven’t found any way to reset my battery’s cycles. I have an iCopy and I tried to reset the cycles number of my battery, but it didn’t work, i4tools shows 100% but it still shows 81% in the settings. Or should I just go with a compatible one? I’d like to keep using my iPhone XS for a few years if possible
After completing all steps battery is showing 100%health i am done all after restarting phone i am getting problem sometimes phone switched off automatically sometimes faceid not working sometimes phone is getting restart plz help me
When I buy from Apple store it way brand new and I think 2 days ago I buy 2 minutes ago I see my battery health I see that message and I even didn’t use my iphone
I found another solution.. i delete file from filza.. but still give waning in setting... the best part never warning in our main screen after respring or reboot
if the battery/phone heats up too much it could desolder or weaken the solder joints. although I have soldered battery terminals with low capacity before
Thanks for the video, but you dint show how to prepare the new battery (before installing the BMS) . And where do we get battery cover / insulation covers? Thanks
* REWA Academy Training Book PRE-SALE of iPhone motherboard repair available now!
Do not lose the opportunity to get limited systematic REWA training treasure (1000 limited stock for pre-sale).
> bit.ly/31I5Nks
You can use the programmer for batteries and screens !!!!😝😝😝iCopy Plus 2.1
You can used box so to change serial number in nand
if you put isopropyl on and around the battery strips it's much much easier to pull
The battery tabs are folded over and soldered to bms, you can pull the out before cutting to give more room and make finished product fit nicer
you can also use big super capacitor and charge using power supply rather than buy battery weld machine, the tabs are very thin so it works
Respect to this channel. It’s very rare finding a problem you have on the internet and finding accurate answers.
Its not a fix or any help... Its a hack to get around apples locking garbage.. no one should have to go to these lenghs to replace a dam battery.. this is getting out of hand... why do people buy these products for apple to do this to them?
The best academy REWA Technology 👍👍👍👍👏👏👏👏
Easier to jailbreak then go in Filza and in Preferences just change the serial number to the new one that’s printed on back of the battery..worked for me
That portable spot sodering is nice. 👌🏼
Hi Rewa, your videos are gorgeous, you always find solutions to solve problems. I have been following you for a long time, I am also a subscriber and many of your videos have solved some battery problems like this. I would like to know where to find the batteries without the connectors and those stickers to reset the battery. I thank you for the answer.
Good and perfect work congratulations rewa technology 👍🥰🥰🥰🥰🙏🙏🙏👌👌👌👍👍
Thanks for watching :)
@@rewatechnology2008 4:45 what repair process do you call that ?? when getting the bms from an old battery to a new one ??
REWA the best lah soal iphone solusion
You need to buy a welder to replace a battery, way to go apple.
Hi Rewa! Big respect, works fine, % as well. Where can we bought the black protective insulation tape? Thank you!
Rewa Technology making fun of apple by showing them their hardwork of pairing components to earn extra dollars doesn't work until we exist
In the end, also need to restore battery charge cycles with some software.
You can use the programmer for batteries and screens !!!!😝😝😝iCopy Plus 2.1
@@Hallal-Almaty are you sure that works to restore health? I have the JC v1s programmer and that can’t update the battery health. The software shows its written but when I install the battery in the iphone it shows the same.
@@shazadhussain4467 you have to restore the phone (suggestion from colleagues, never tried).
@@ПавелПенчев-э6и Thank you... I’ll try it.
Enconstraste la solución?
If apple see this vidie then next time apple place the bms circuit inside of the battery packing😆
Lol your grammer
Almost have a heart attack reading this comment 😂
@@graphicscardtech3167 🤣🤣🤣
Yeah
😂😂😂
Very nice and perfect job... Thank you to teach us...
The spot welding thing is a concern for most. There should be a non-destructive way. Like just copying and pasting. Kudos Rewa.
Every factory uses spot welding when they connect battery to the bms
Why you didn't show us the battery health after replacing? It stays the same as before replacement.so if you have a battery with 75% max charge it will be the same after replacement
You'll get better or worse health depend on cell you bought. It wont or will stay the same, since BMS does not affect BH (at least in this case because manufacturer's BMS has higher quality than 3rd party one). It just contains Apple encription, thus you'll need them to not get the annoying message.
I have the same issue ( iphone xr). I replaced bms and reprogrammed. The battery health that phone shows is still 86% ( as it was before replacement) and the software on PC and programmer shows 100% ( as I typed in). Do you maybe know how to fix it?
You need a device to reset the BMS to 100%
My uncle once did this with my iPhone 7's battery And it pretty worked well ✌🏻😂
iPhone 7 doesn’t need this
This battery transplant surgery only started with x,xs and max…not before models.
There’s no such thing as iPhone 7s
@@thomasngo9559 there’s an apostrophise 🤦🏻♂️🤦🏻♂️🤦🏻♂️🤦🏻♂️🤦🏻♂️
Where i can buy the protective cover and the insulating tape? :) very good Video!!!
Most likely AliExpress, honestly a small piece of electrical tape will do just fine
I guess battery repairs got more expensive to do... but this is dope to know.
You can use the programmer for batteries and screens !!!!😝😝😝iCopy Plus 2.1
Азамат Игликов does it work with iphone 11 screens? I have 1st gen and it does not work with batteries and 11 and up
@@Hallal-Almaty it cant for iphone 11 series
This means when change battery original to fake there is important battery massage that fake battery yes?
How often is the notification will come up?
Parabéns vocês merecem todos os likes
Hi! Thanks for posting this super informative video. Can you tell us why it's necessary to use this odd little spot-welder? Could the battery contacts not simply be soldered into place?
They can, although solder can snap when you fold the battery board back into place. Using the original nickel sheets means you can bend it without the chance of any faulty connections.
Is it possible to use a soldering station for this situation ?
Exactly my question 🤣 there’s mini spot welders for £20ish on eBay I think I’ll invest
Hi bro, if I don't have the connector from the original battery? Is there a solution to fix the battery service problem?
why at the last you not show the "Battery Health" Maximum Capacity???
The whole point was to show battery health at the end...dislike because of waisting my time
What's up with that "activation board"?
8:43
Is that just a charger, to ensure the correct function of the cell?
Is for cheking voltages, cause Apple IC charging are very fragile and a bad voltage can burn it.
Hi
great work but after soldering where can we buy black glue ??
Kind regards
Not really techy but will this affect the data of the phone itself or the performance especially in updating IOS? For xs
Can't you just use a reprogramming tool to input the credentials of original battery into replacement one, like in older iphone 7/8 batteries?
You can use the programmer for batteries and screens !!!!😝😝😝iCopy Plus 2.1
No, We cannot use reprogramming tool to copy the credential of original iPhone battery. Because, Apple use EEPROM in battery circuit chip, which ties the part to the iPhone.
@@MrAshwin27 this is correct
Good video! Can you make a video for iPhone 11 pro max battery replacement please?
We haven't done a video on iPhone 11 Pro Max battery. The procedure is like iPhone 11.
What if we don’t have that welding machine and that activation board/installer?
Hi, could not find the black protective cover and installation tape used in this video.
I don't understand why you need to activate the battery. When you plug the new battery into the iphone, shouldn't it start charging right away and accept it as a genuine battery?
Is it okay to use the iphone without the original battery flex? Will the "important message" cause any problem?
How about the battery health?
U may reset it with icopy plus
Baterai low kapasity
The Battery Health will be shown in the system normally, but the shown data still comes from the original battery.
I thought of self replacing my xs max 89% battery i guess I'll have to go to Apple to do i for me
@@AppleReviews
Not really, you can use lts instead, in combination with acid.
Very good job
Nicely done.
Yeah I’m gonna go ahead and live with the notification lol
Its much appreciable thing but can you tell me its reliable after long time use
I mean the risk of battery swolen and any other heating issue
How about XS MAX?
There is two BMS logic boards for the two different cells.
Need to transfer them both?
Yes, 2 BMS on the battery of iPhone XS Max could be transferred together.
But the flex cable of 2 BMS should be more careful about it during the transfer, avoiding to damage it.
Then I have original’s battery? (Already lost it…)
How about using a different Xs battery”s one.
Maybe same problem happens gonna happen again?
Does this do this for a screen replacement too?
Great job thank you! Does this also work with ios 14?
Yes.
Any iOS should work
@@mishkattashdid8239 I think just 13 and up because replaced a screen and better for my old 6 running iOS 12 and it said nothing about Display Warning
How often the battery warn come on if you used after market battery? Thanks
is there any software solutions?
Thanks rewa
Nice job sir
Can make iphone have its battery health if dont have the original flex cable?
Pro tips. When you bought a new iphone if your battery health goes down to around 89 below just buy a new battery and keep the original battery and when the time comes if you want to upgrade then put back the old battery and sell it still good battery health 😂 sorry for my bad english
how about the battery health? it will automatically turn to 100% or you have to program it?
Exactly, he did not show this in last step
how? all old data will be left 😜 no repair
Yes, you need board or supply to activate battry and programmer to erase old data and program new 0 cyclus. On iphone 11 and above you need small board too which remains with the battry. Here it is not shown that.
Apple will make the bms such a way that it won't work after power was cut
It's done on most laptop battery already
I have A Request video to you
Please A Don't ignore.
"Make a short video about iPhone xs battery vs
iPhone 11 battery" (only size Comparison)
Or,
Otherwise please reply me in comment. What I can
use ip11 battery in my iPhone XS.
I want to know that. Let me know that bro please
A
Love from Bangladesh❤️🇧🇩
Dose it also fix battery health function?
where I can order the tools and materials
I think, the fired apple ex engineers word for REWA and revealing everything
Great sir ...
We already use this technique in Pakistan alit when we dont find any phone's battery thats the best solution...
I always learn from ur videos
Love from Pakistan
Thanks for your support and we are glad to hear that :)
Hello dear.
I loved your all videos, you make it very good. And I have question refer to the battery important message. My question if I lose the original battery of the iPhone and then it is show up with the message"importanct battery message" so how can we solve this problem?
u have to change socket ribbon battery
Why do you have to 'Activate' the battery? I'm currently using a replacement official iPhone battery, could I just swap the battery management board and be done or do I have to activate it as well?
great job
Any chance the maximum capacity can be reset to 100%?
No, u need to replace the battery since this number lowers over time (depends on usage)
@@tedlienert8029 it's possible, however you need a programmer such as JC 1000s, then you can mod it to 100%
@@aldenviriyatanudjaja5234 will the capacity grow over time and be recallibrated auromatically because the new battery is installed?
@@sadpouofficialshop chances are no, you will need to recalibrate it manually using the programmer
@@aldenviriyatanudjaja5234 but will the battery function normally at full capacity without a reprogrammer?
Thanks
You can use the programmer for batteries and screens !!!!😝😝😝iCopy Plus 2.1
Isn't supposed that the icopy 2.1 tool can copy the battery to avoid the warning message?
Nope
After transfering the bms to the replacement battery, does it say "normal" in 3utools or it will appear that the battery has been changed?
Does it have to be done like that?
What if i copied the serial number from the old battery to the new battery
Would that fix it??
After reprogramming it I plugged in the battery to the phone to see if everything works fine. The battery capacity is still the same (86% in my case) so my programmer didn't work. I tried reprogramming 3 more times. Nothing has changed. Software and programmer shows battery health 100% but after plugging into phone (iphone xr) it shows 86. Why is that? How do I fix it? I would appreciate every help.
Could you give me advice? When I change board on battery, activated it, set cycles on 1 and set battery on 100% i got issue with battery capacity in mobile. My XS Max show me battery condition only at 78% but when i put battery on quanli iCopy plus, it show 100%. Could you give me an advice what iam doing wrong? Thanks
How about copying all battery data and write it in the new bms ? This method will not reset battery health.
where do i stick battery stickers? I can't find it anywhere on the internet, can you advise me? Thank you
Ifixit
@@hugo4339 send my link pls. Thx
Does the model no. Get changed after this?
I fear my iphone has a fake battery
After replacing the battery cable the maximum capacity will remain the same as before. How to solve that?
Some Tools can change the battery %. You have to let the iphone read another battery data first though
Enconstraste la solución?
I never changed battery on my iPhone 12, yet im recieving this error unknown part battery and the phone doesnt charge even after connected to charging port for hours
WHEN SOLDERING CATHODE IS NICE BUT WHEN ANODE.... BOOM! BATTERY ALWAYS SHORCIRCUIT AND OF COURSE BATTERY BOARD IS LOST
Can I use a k-weld battery spot welder to weld the bms.
Where can those batteries without cells be bought?
REWQ TECHNOLOGY great job
I have one doubt I have 2019 model MacBook (trutone display) ufortnatly Display is Brocken
then I change display but keyboard backlight is not working I try another display but same condition.
I put old (Brocken display) DISAPLY keyboard backlight its working fine
could you please tell me solution
did you match the correct year screen, if you mix 2018 and 2019 iirc it messes with lid sensor
@@Slot1Gamer Thanks
iphone xr also need to do this?
What aboutt the battery health value...please help..
After doing this It writes my old battery percentage, not 100% maximum capacity... Any chance to avoid this?
Hi, is it still showing your old battery percentage? (I’m told that after doing this, the phone gotta be charged a couple of times until the battery health changes)
@@HiItsK yes it is... Even showing that I need to replace battery...
@@Mirandess1 Is your battery under 80% health? Does it affect to your phone's performance?
@@HiItsK Today i have removed this old battery(replaced original with new one) and this is third battery, it is not good idea to do this! Trust me! And yes It showed old battery percentage...
@@Mirandess1 then, would you recommend me to take it to a Genius Bar to replace the battery? I haven’t found any way to reset my battery’s cycles. I have an iCopy and I tried to reset the cycles number of my battery, but it didn’t work, i4tools shows 100% but it still shows 81% in the settings. Or should I just go with a compatible one? I’d like to keep using my iPhone XS for a few years if possible
After completing all steps battery is showing 100%health i am done all after restarting phone i am getting problem sometimes phone switched off automatically sometimes faceid not working sometimes phone is getting restart plz help me
Hi, i have question, what about iPhone SE 2020. do you need tag on flex, or you can just replace BMS board. When you replacing battery
What happen if i soldering battery flex cable, not weldering the flex cable?
notif about the battery in the setting - battery
why u chek from setting - about ?
Sp iphone X and older it won't show? Except for the face Id if the screen is replace?
When I buy from Apple store it way brand new and I think 2 days ago I buy 2 minutes ago I see my battery health I see that message and I even didn’t use my iphone
@World Viral Daily after watching more video I relaize that I update my iPhone to beta vershion witch is ios14.5 beta3
I found another solution.. i delete file from filza.. but still give waning in setting... the best part never warning in our main screen after respring or reboot
Cant use solder for joining that old pcb to new battery ?
if the battery/phone heats up too much it could desolder or weaken the solder joints. although I have soldered battery terminals with low capacity before
Can you tell me what kind of torch is from?
Hi, please feel free to contact us at sales@rewatechnology.com for any demands.
Thank you :)
Thanks for the video, but you dint show how to prepare the new battery (before installing the BMS) .
And where do we get battery cover / insulation covers?
Thanks
The preparation materials can be bought, and please feel free to contact us at service@rewatechnology.com for any demands.
Thanks :)
We supply battery cells with all parts you need to replace a bettery .
@@rewatechnology2008 I would love to have my 11 pro max Face ID fixed
Will
My phone break if I don’t do anything?
Do you have any solution for screen ?
Yea, you have to transpose the Touch IC.
For the solution of Non-genuine Screen Warning, please check out our earlier UA-cam video as a reference:
ua-cam.com/video/agq2HPK-WqY/v-deo.html
Can I not use just iCopy too set data over
Why is battery replacement so hard?😮
what if you buy second market iphone with non genuine battery come ?
any solution ?
Where can I buy battery without module?
Kunde : könnten sie mir Bitte mein Akku für das XS Wechseln ?.
ICH HEUTE BMS WECHSELN GAR KEIN BOCK.!
From where can we supply those new stickers
Where can we get isolation tape?
I have did it , abd the error message not shown , but i get old battery procent ? how fix it ?
so good