Hi couple questions as im new to this and need to do similar to plastic bumper.. Was it a plastic primer ? Did u use a base coat and clear over or what did u use in gun ?
your videos gave us the confidence to buy a salvage car for only 40% of the retail price. My son and I are doing the work. I used the 2 part clear epoxy to fix a cracked headlight then followed your video for restoring headlights- $10 fix for a part costing $600 new. Tomorrow we start on the cracked front bumper cover. We would never think about doing this kind of work before your videos. PS- the repair estimate for the damage was more than $3000- we think we can fix everything for less than $100.
so i has started to repair 2 vauxhall vxr bumpers that i bought for 100€ each from the uk. these one's cost new nearly 700€ each... without the paint job it is done for 25€ with following this video's :D
@@DHarris240sx - Becoz it's not really a DIY job. PLASTIC WELD by a Pro. is Quite Expensive - more than the Total Cost of the Repair by the M4M Ladz - if U use ColorMatch rattle cans. Most DIY folks Don't have a Compressor lying round ! 🤔 Thinks: an old vacuum cleaner and some Duct tape and a few pipes with gradually smaller diameters.....then U could....... 😉
I was looking bumper repair videos for myself so i can save money from buying parts and always con-artist ripoff auto shops and find your video the most helpful, love it and very easy to follow tips. thank you so much
Cracking video!! I watched the others video as well and gave me so much confidence to do the repair myself with spray can. Gone ahead and did. bish, bash, bosh. Saved £500 and now I have a full kit for more repairs. Thank you!!
Man I've watched 3 of your videos and am more impressed with your work and skills than any other channel. I subbed hands down and range that notification bell!!
Terrific repair, - heating the carton staples to melt into the plastic is genius. Plastic window screen mesh in place of bandage gauze also works well.
Jesus! Zip ties are the worst method ever. Unless the intention is to make the repaired part look like Boris Karloff's, Frankenstein! LOL 😂 Use basic soldering iron, anything from 30W to 100W, with a flat tip, will do just fine and it's dirty cheap. If you want to go fancy there's flat and broad plastic solder tips. Which make it even easier! Using the video case as an example, no welding "material" is needed. Just the soldering iron and 5 minutes of your time. To make life easier, some aluminum tape on the front will keep it nice and tight while soldering on the back. If done carefully most probably the front would be good enough to be left "as it is" in most cheap car repairs, almost unnoticeable after soldering. Zip ties could be used as solder material or even to bridge larger gaps also soldered, but that's it. ;-)
2 cents on the way! ;-) When you pulled out the soldering iron I was convinced you were going to do what's reasonable and logical... Solder the broken edge back into shape! Damn I was surprised you didn't! It's so much easier and way more efficient. After being solidly conformed to it's shape then you can add whatever reinforcing layers and methods. But that would be done over a repaired surface. BTW for a crack that size it would take about 5 minutes, top! ;-) One more tip. For a case like this. Use aluminum tape, on the front side, to hold it together while you repair it from the back side. Cheers
Epoxy does not bond chemically to polypropylene bumper. It only creates a mechanical bond, and the bumper at one point in time may crack again due to constant impact, or if the metal staples you used dislodge somehow. In order to form chemical bond you need to use polyurethane resin. This is better than epoxy but you have to find the kind that stays flexible. Or better yet use plastic welder.
Thankyou for all of your advice! I have an Escalade ,used but l Love it!!Already done some detailing..l have the small scratches, that will grow big..The plastic bumper, on going at soon..(l have little holes in my side mirrors...l know l have to use bondo..but l want to treat them gentle!!Thankyou again for advice!!!
It will just re-crack sooner than later. The outside crack needed to be v- grooved, then plastic welded or melted back together with a soldering iron before using filler.
Thank you so much for taking time to make and post this video!! I LOVE that you use supplies from things we already have, or can easily find. Thank you!!
Great job on your video, a plus-plus thumbs up on using some type of metal to reinforce the "crack" I which I could find a perfact match for my paint and use a rattle can. Rather that load my gun up with $$$$ paint for a 3-4" crack Great job
Thank you for your guide. I followed you method, had a massive L shape tear in my bumper. I made mistakes though, one, 1. put too much filler so it's noticeable and 2. Didn't have primer, ordered over the internet, throught it came with primer, but just laquer. I just painted over the filler with my car base coat. However, it doesn't look that bad. I have just orderered primer. What I am going to do next week, is sand of the paint and the excess filler, then I will use primer, 800 wet sand then my base coat, then with the lacquer clear coat. Thankfully, the hard job is done so a small touch up and I don't have to remove the bumper. Also, tried to use the staple method, didn't work out for myself but the epoxy and medical bandage, worked great, rock hard solid.
Just brought some primer so all ready for the weekend. The most important tip I can give is, sand the area well, to flat, then put primer, not to much otherwise you be sanding all day. Mine doesn't look bad, but I want to get rid of the high spot of the filler. PS. I am a female DIY, never have I done this before and this video was very easy for a novice to follow. However, I think I well use my sander to get rid of the filler, it will save me time.
I noticed at 6:10 there's still a tiny crack at the top where it first started from, after using bumper filler my bumper still has that tiny portion where I didn't use any. What do you think about leaving that crack still unfilled ?
Wow amazing. I have a dodge journey with 2 small cracks and it has come loose off the clips. So I'm being charged almost $2000😭thanks for your video will definately help me.
I like your guide, simple yet effective. Just don't mix epoxy or bondo on cardboard, or at least use parchment paper. It will save some material. Porese material like cardboard will soak some portion of epoxy or bondo. It doesn't matter once or twice, but on the long run you can save some money. Keep up the good job ;)
Great video brother! It's really incredible what you can do with epoxies elbow grease! It came out looking amazing! We just did a how to on a fiberglass bumper with similar techniques. Thanks for sharing your experience and keep em coming!
I just weld with PP plastic welding rod with a 80w iron run the solder along the crack on the outside and cross the solder a few times on the back. very simple ,it takes 10 minutes to do this job. then paint.
If you want advice about your scratch, car or whatever instagram.com/mad4motors/
Hi couple questions as im new to this and need to do similar to plastic bumper..
Was it a plastic primer ?
Did u use a base coat and clear over or what did u use in gun ?
your videos gave us the confidence to buy a salvage car for only 40% of the retail price. My son and I are doing the work. I used the 2 part clear epoxy to fix a cracked headlight then followed your video for restoring headlights- $10 fix for a part costing $600 new. Tomorrow we start on the cracked front bumper cover. We would never think about doing this kind of work before your videos. PS- the repair estimate for the damage was more than $3000- we think we can fix everything for less than $100.
Hey that's sounds awesome and you are getting to do the work yourself! Thanks for the nice comment!
Look why not plastic weld it and done? ╮(─▽─)╭
I think he was trying to make it stronger.
so i has started to repair 2 vauxhall vxr bumpers that i bought for 100€ each from the uk.
these one's cost new nearly 700€ each...
without the paint job it is done for 25€ with following this video's :D
@@DHarris240sx - Becoz it's not really a DIY job. PLASTIC WELD by a Pro. is Quite Expensive - more than the Total Cost of the Repair by the M4M Ladz - if U use ColorMatch rattle cans. Most DIY folks Don't have a Compressor lying round !
🤔 Thinks: an old vacuum cleaner and some Duct tape and a few pipes with gradually smaller diameters.....then U could....... 😉
That's a Savage tip with the clips from the cardboard box. I'll remember that. All the best from Athlone.
Já vi usarem tela metálica.
I was looking bumper repair videos for myself so i can save money from buying parts and always con-artist ripoff auto shops and find your video the most helpful, love it and very easy to follow tips. thank you so much
Cracking video!! I watched the others video as well and gave me so much confidence to do the repair myself with spray can. Gone ahead and did. bish, bash, bosh. Saved £500 and now I have a full kit for more repairs. Thank you!!
Your work is so clear, simple but most of all, gives me so much confidence to this on my own.
Nice video - short, no unnecessary talking (really appreciate that) and good info. THANKS.
This is the simple approach I've been looking for. Brilliant idea using the packing staples!
This is more enjoyable then those 4-10 episode of restoration videos out there
Great tip to use those staples mate
agree! great idea
Man I've watched 3 of your videos and am more impressed with your work and skills than any other channel. I subbed hands down and range that notification bell!!
Terrific repair, - heating the carton staples to melt into the plastic is genius. Plastic window screen mesh in place of bandage gauze also works well.
Those metal clips are a great idea, no more drilling holes and zip tying!!!
Jesus! Zip ties are the worst method ever. Unless the intention is to make the repaired part look like Boris Karloff's, Frankenstein! LOL 😂
Use basic soldering iron, anything from 30W to 100W, with a flat tip, will do just fine and it's dirty cheap. If you want to go fancy there's flat and broad plastic solder tips. Which make it even easier!
Using the video case as an example, no welding "material" is needed. Just the soldering iron and 5 minutes of your time. To make life easier, some aluminum tape on the front will keep it nice and tight while soldering on the back.
If done carefully most probably the front would be good enough to be left "as it is" in most cheap car repairs, almost unnoticeable after soldering.
Zip ties could be used as solder material or even to bridge larger gaps also soldered, but that's it. ;-)
Thanks a million for sharing your work. Its easy, simple & cost effective. Cheers!..
your videos are excellent snd have saved me hundreds of moneys
Nice!! Them headlights just need to be cleared now 👍
2 cents on the way! ;-)
When you pulled out the soldering iron I was convinced you were going to do what's reasonable and logical... Solder the broken edge back into shape! Damn I was surprised you didn't! It's so much easier and way more efficient. After being solidly conformed to it's shape then you can add whatever reinforcing layers and methods. But that would be done over a repaired surface. BTW for a crack that size it would take about 5 minutes, top! ;-)
One more tip. For a case like this. Use aluminum tape, on the front side, to hold it together while you repair it from the back side. Cheers
Well oil beefed hooked!! Great video. Liked and subscribed.
Aye, I could do with a bit of FIG JAM too. Feck I'm good, just ask Mick! 😉
Epoxy does not bond chemically to polypropylene bumper. It only creates a mechanical bond, and the bumper at one point in time may crack again due to constant impact, or if the metal staples you used dislodge somehow. In order to form chemical bond you need to use polyurethane resin. This is better than epoxy but you have to find the kind that stays flexible. Or better yet use plastic welder.
Thank you sir for sharing very useful knowledge. The best..👍👍
Great work mate🧰🧰
Thankyou for all of your advice! I have an Escalade ,used but l Love it!!Already done some detailing..l have the small scratches, that will grow big..The plastic bumper, on going at soon..(l have little holes in my side mirrors...l know l have to use bondo..but l want to treat them gentle!!Thankyou again for advice!!!
Beautiful work. Heat gun works on pins too
Bumper Stitches!!! Excellent.
It will just re-crack sooner than later. The outside crack needed to be v- grooved, then plastic welded or melted back together with a soldering iron before using filler.
Sure if you're willing to PAY for it! Most of us battlers are more than happy with the results we get thanks to Mick from M4M!👍
Thank you so much for taking time to make and post this video!! I LOVE that you use supplies from things we already have, or can easily find. Thank you!!
Use a Fiber Glass Patch on Back Side to Give Bumper Extra Strength...
While we're burning money we might as well plate it in gold.
Good solid job. Headlights ?
Great job on your video, a plus-plus thumbs up on using some type of metal to reinforce the "crack" I which I could find a perfact match for my paint and use a rattle can. Rather that load my gun up with $$$$ paint for a 3-4" crack Great job
yo i love your videos man new subscriber!
Great Job I’m going to fix Volkswagen Golf rear bumper thanks for tips and video
Thank you for your guide. I followed you method, had a massive L shape tear in my bumper. I made mistakes though, one, 1. put too much filler so it's noticeable and 2. Didn't have primer, ordered over the internet, throught it came with primer, but just laquer. I just painted over the filler with my car base coat. However, it doesn't look that bad. I have just orderered primer. What I am going to do next week, is sand of the paint and the excess filler, then I will use primer, 800 wet sand then my base coat, then with the lacquer clear coat. Thankfully, the hard job is done so a small touch up and I don't have to remove the bumper. Also, tried to use the staple method, didn't work out for myself but the epoxy and medical bandage, worked great, rock hard solid.
Just brought some primer so all ready for the weekend. The most important tip I can give is, sand the area well, to flat, then put primer, not to much otherwise you be sanding all day. Mine doesn't look bad, but I want to get rid of the high spot of the filler. PS. I am a female DIY, never have I done this before and this video was very easy for a novice to follow. However, I think I well use my sander to get rid of the filler, it will save me time.
Great job 👍👏
Mate that was one of the best vids I’ve seen cheers
Beautiful work. Great job explaining steps and logic behind the process. Thank you!!
Fantastic! Thanks for sharing your skills.
so far the most economical fix i have ever seen
Amazing OMG I'm a subscriber for life!!! Thank you
You are a genius!! Man
I noticed at 6:10 there's still a tiny crack at the top where it first started from, after using bumper filler my bumper still has that tiny portion where I didn't use any. What do you think about leaving that crack still unfilled ?
Thanks. You just helped me out alot
Yet again, you are a hero!
You make it look to easy. Might have to give it a try. Thanks for the informative video 🙏
Great job explaining well.
What crack???? That looks nice!
Wow amazing. I have a dodge journey with 2 small cracks and it has come loose off the clips. So I'm being charged almost $2000😭thanks for your video will definately help me.
Superb repair ! Love this channel ⭐️⭐️⭐️⭐️⭐️🇮🇪
nice job. did you spray the whole bumper or just where the damage was? how many coat of base and clear is good to put down for pro results
All that gave this video thumbs down are body shops that are mad for him sharing knowledge, thanks man
Cause it will fail very soon, that’s why ..
Fantastic job 👍
Great idea with melting staples into the bumper !!
I like your guide, simple yet effective. Just don't mix epoxy or bondo on cardboard, or at least use parchment paper. It will save some material. Porese material like cardboard will soak some portion of epoxy or bondo. It doesn't matter once or twice, but on the long run you can save some money. Keep up the good job ;)
Thank you for the amazing simple yet working DIY fix!
Great work, an awesome result, there is no evidence of the damage at all, well done !! x.
Super awesome job!
Craking job mate!!! I will fix my bumper now and save some money
You have done a better job than others I had come across on UA-cam just one thing the headlights need cleaning rest welldone a very good job u did
Great video brother! It's really incredible what you can do with epoxies elbow grease! It came out looking amazing! We just did a how to on a fiberglass bumper with similar techniques. Thanks for sharing your experience and keep em coming!
Would paper clips or bobby pins work instead of the cardboard box pins? I've never seen those cardboard box pins before haha
you sir are a genie
That's... incredible.
I just weld with PP plastic welding rod with a 80w iron run the solder along the crack on the outside and cross the solder a few times on the back. very simple ,it takes 10 minutes to do this job. then paint.
thank you, very informative vid.
Thanks mate👍
all your vids I have watched are absolutely amazing especially the curb rash one . Thank you so much for all your videos and please do lots more.
Looks awesome I need mine doing
Top job man
Great video, also checked out your spray can repair one and you’ve filled me with hope! Keep up the awesome work!
Wow your talented!!!
U have great videos!! 👍👌👏
Another great solution. Good job!
Great tips thank you
THANK YOU SOOOOOO MUCH!❤
The pins are a great idea a s cheap. I use painters self adhesive mesh repair tape for drywall. Same idea as the band aid tape.
Amazing job !
Great video very informative a few tricks there I'd not thought of many thanks for sharing
Excellent home repair. Thanks!!
Very informative videos and thanks to what you do keep up the good work mate
great job man
Love this idea
Whats the name of the pudding you put on the crack before you sanded it?
The pudding I end up using was by "Bondo" Professional Gold Body Filler. - inside there is a small tube- creme hardener. It worked pretty good!
Nice work man 👍
Good job paintman
Crackin job Mate 👍👍👍 (Pun intended)
Awesome job
Really useful! Thanks!
Damn nice work
Absolutely brilliant video.
Great idea with metal clips. Can not remove rear truck bumper. Cover cracked. Can Staples headed from outside use bondo , sand lightly and paint?
Absolutely Fantastic!
After the regular paint coat, did you have to apply the shiny glossy paint?
that looks bloody mint. from what it was.
Just found your channel. OMG your great. I have subscribed. Wu Hu. Taking the scary out of body repairs.
do you think a newbie with the proper tools can get the same result as you or a decent one ? or does it depend on the newbie skills ?
What flexible body filler did you use? I’m having troubles finding a cheaper product that’ll work with plastic bumpers
Hmmm, this might help with my 166 front bumper cover. Rare car, so hard to find/costly to get another bumper.
Well done excellent 👍
Very well done man
I'm highly impressed!
Awesome work