How to Fix BMW Engine Shake | F30 Motor Mount DIY | 328i 3 series
Вставка
- Опубліковано 28 чер 2024
- After watching this video you will know how to solve that BMW engine shake. In this How to tutorial we go through the replacement process of the F30 N20 & N26 motor mounts.
N20/N26 Motor Mount (Right): bit.ly/3mlU3O9
N20/N26 Motor Mount (Left): bit.ly/3D8Rrde
E30 Tow Hook: ebay.us/3RXUoE
Engine Mount: amzn.to/2XQKY7b
E - Drill Bits: amzn.to/3o5pH53
Drill: amzn.to/39Es1aA
Of all the things that can cause your BMW engine to shake this is probably the easiest to fix. To replace the motor mounts on the F30 should take no more than 2 hours from start to finish. Giving your newly painted under panel time to dry. I wouldn't say it's a hard 2 hours, but a little tedious.
Thanks for tuning in. If you are looking for a complete tool kit as well as video gear hit the links below.
Tool Kit: kit.co/fritzramos/bmw-mechani...
Video Gear: kit.co/fritzramos/filming-gear
If you are looking to get started on UA-cam, consider Tube buddy as it has helped me out a great deal. Try it out for free: www.tubebuddy.com/financialfi...
Some of the above links are affiliate links. By using them you help support the channel at no additional cost to you. Thank you for your support.
00:00 Intro
00:53 Diagnosis
01:31 Things to know before the installation
01:45 Picking the correct mount
02:21 Setting up the engine Support
02:58 Proper car positioning
03:18 Uninstallation
04:10 Old Vs new mount & Proper orientation (Driver)
04:31 Installation (Driver)
05:07 Uninstallation (Passenger)
05:24 Old Vs new mount & Proper orientation (Passenger)
05:39 Installation (Passenger)
06:09 Torque Specifications
06:38 Panel Reinstallations
07:06 Before & After
07:19 Tips and Final Thoughts - Авто та транспорт
Fritz, you are the most underrated BMW DIY UA-camr.
Thank you, I guess I just have to work harder and keep improving 👍
@@FritzRamos hey fritz! Do you know where the transmission mounts are on these N20 engines?
@@DuckMcDuckinson ua-cam.com/video/4SpINHbylzs/v-deo.html
@@FritzRamos fritz hey there again! I’m gonna tackle this mount issue tomorrow and I wanna know when you use the engine brace and you start tightening down that middle hook that hooks to the tow hook, does it lift the engine like yours is doing in the vid? Also do you want to tighten down that middle prong that spins down onto the middle of the brace as tight as possible?
@@FritzRamos also the tow hook you have, does it screw all the way down into the threads ontop of the engine? Because I have the same hook and it’s a pain to keep tightening it down and it’s still not all the way threaded in. Or do you just tighten it down as much as you can even if there are a few threads that aren’t in?
Didn’t even realize I wasn’t subscribed yet, I see your videos all the time!! I am subscribed now 100%
Really nice video. From another F30 enthusiast... great job. Impressive!
Thank you. Nice to meet a fellow enthusiast 🤝
Fritz I love you man best video on these out there thanks a ton!
Very nice video. Sooo clean (literally) and straight to the point.
Thank you!
again a great demo and super clear instructions
Thanks Thomas!
I just completed this job last night and let me tell y’all, it ain’t no where near as easy as it looks 😂
I had to take off the top strut brace so I could lift the engine high enough to put in new mounts 😭
@7:10 perfect 👍🏻,, i always do that test to check the mounts , great u did it before @1:20 and after
Nice video Fritz!!!!
I've watch all related videos of this repair and this is the most straightforward, detailed, and best example of how to perform this repair! Good Job Man
Thank you. Glad you found it useful.
@@FritzRamos hey fam can I use rhino ramps to keep the car elevated?
@@DuckMcDuckinson I don't see why not
@@FritzRamos alright thanks fritz!
@@FritzRamos hey fritz just a quick question, I just drive the car on the ramps then use the engine brace? I know it sounds stupid to ask this question.
Holy **** now i know what that noise is, glad i decided to look at your vids.
Glad I could help
Hi very nice video! Straight to the point.
Quick question: do you recommend replacing the gear box mounts at the same time or do they last longer?
Thanks!
Great video. How many miles does it need to change? Thanks.
Thank you so much!
The how to clean the engine bay info pop up was a brilliant thought. I was like hmm he did it and the info popped up. Lol
Thank you for that input! What you just described was what I was hoping to achieve. Provide people with information at a relevant point of the video without taking away from the current topic. 🤜🤛
Is the process similar for the G20 330i?
Hey just went through it the “supercharger” wine is the timing chain going
Even I have a N55 I watched the full video. Great content.
Thanks! Hope it was helpful in your case 😅
Well it was indeed. Got the motivation that I can manage the job on my own :)
@@Pa-hy1te You got this 👍
What size torque wrench did you use? Is there a link for that?
How similar is this to the steps to replace mounts on an F30 340i? Anything else to remove?
Would you recommend the e30 tow hook with a g20 engine 2019?
I have a 2014 BMW X1 sdrive28i I get a vibration sound on the highway doing 70 to 80 MPH only on highway at those speeds
My engine shakes, but the mounts were replaced when I put a new engine in my 328i. Honestly don’t know what it could be, but besides that I’ve had zero issues with the car.
are they same part for boths sides??
is it the same for the 328d n47?
I am hav8ng problems with vibration when idle, any ideas?
Hey man, new subscriber here and thank you for the detailed video.. i have a question, not sure if my issue is the same but my car vibrates and resonates throughout the body, inside the cabin, doors, steering wheels, pedals and muffler. The shake is mild and its the same wether the engine is on idle, drive or reverse. Do you think the engine mounts are the culprit? Thanks heaps.
Man sounds like it. I had a high pressure fuel pump go out on me and when it threw the drivetrain malfunction, whenever it went to a stop, the engine would vibrate crazy!
Hi,
This can cause the metally vibrating sound as well at the start, or its the turbo wastegate flaps loose?
Thank you!
Did you figure it out bro?? I have a metally vibrating sound too
How long this take ?
how many miles did you have on the car when you did this
You make it look easier than what other people have shown. I get a shake for about 30 seconds through the cabin on cold start and its fine when I accelerate, would this still be the engine mounts?
That might be something else. The motor mounts would be stiffer when the car is cold
Awesome Vid. Pinoy ba? Saan mo?
are they same part both or diifernt each side?? then part number also thanks
Different. N20/N26 Motor Mount (Right): bit.ly/3mlU3O9
N20/N26 Motor Mount (Left): bit.ly/3D8Rrde
How manu kilometres ??
Fritz, how long did it take you to do this project? Also would the steps be the same for a F36 435i xdrive gran coupe?
With filming, about 4 hours so maybe cut that in half for yourself. I would imagine that the overall process is the same, but with slightly less working space on the bottom side.
One more question, did you have to lower your sub frame? (I don’t think you did based on your video but just wanted to make sure) (Some posts in the forums talk about needing to lower the sub frame)
Also I appreciate the quality and detail of your videos! Thanks
@@bijuc6157 if youre raising the engine, no need to lower subframe.
@@tugrulbey3095 thanks for your response!
Would this be the same for xdrive?
Similar. Access might be a little less on the X-drive.
When he said “it’s probably not your engine or your motor” 20 seconds into the vid I was skeptical 😂.
Is this same for f22 m235
It's similar. I'll do one for the m235i in the future
is this same concept for f32 with n55?
Yes the overall steps, concept, and setup are similar.
@@FritzRamos what about for G20 330i?
All the shops around me are quoting 7 hours for this, around $1100. Seems pretty ridiculous.
Really?! I think I did this in less time while filming
What's the difference between the E30 tow hook and the stock F30 one that comes with the car?
The E30 tow hook is slimmer
@@FritzRamos ah thanks! Can the stock one not be used?
@@Oockeshoek as long as you can tag it in all the way without pinching wires your fine and be careful when pulling it out
@@FritzRamos thanks!
Hi, do you have the Video before and after comparison?
Sorry, no. Just the before and after that you see in the video
what do u mean rubber pad should face rear car? which part ???confusing here
middle
Is the process the same for 2 series?
Exact same for the 228 but a little less space. The m235i is similar with a few differences. I'll make on for our cars later on
@@FritzRamos ok, also, is your 235 X drive? I’ve noticed some of the processes for a few of your tutorials are a bit different when I attempt them on my x drive 235
@@FritzRamos looking forward to that video! I had the same question. I know a company called Revshift makes some for the F8x, F3x, and F2x cars, so it would be interesting to hear your take on their product when you make the video.
Do you have to drop the subframe
Nope
@@FritzRamos mannn lol I got an estimate for 1100$ for m235i to replace the motor mounts because they said they have to drop the subframe.
@@Jwips. I mean, I guess you could do it that way. I would just use a engine support and if I really needed to, slightly lower the subframe but there shouldn't be a need to completely drop it if you don't want to. Where are you located?
@@FritzRamos Las Vegas
@@Jwips. hit me up on IG @vroomtuber and I'll see if I can put you in contact with my friend
I replace mine at 77k and now its at 107k And when I put it to drive i feel more vibration and even more when I turn on my AC. Its possible the motor mounts when bad that soon? I took it to a mechanic and he said my car is at 100k what would I expect. BTW my is an f30 238i 2016.
If you bought it from FCPEuro you’d have a lifetime warranty on the part.
Would this cause a Drivetrain Malfunction code to pop up on BMW ?
Yours don't look that bad