Nice to see how this performs on 2s. So far, reviewers have only shown 3s, but if I were to buy this one, I'd definitely use both 2s and 3s. That prop-wash was nasty though. lol Great video.
I have a couple of builds with the O3, but I am mostly still rocking the Vista on most of my builds. The 03 has nothing on the Vista except for the 4K.
Thanks for this video! As you said, it would have been easier to assemble without filming. Probably this is why there are not too many detailed build videos where you can really see all the details of a build from all angles. I have a mobula 8 with the vista air unit, but the pavo 20's pusher configuration is tempting me. For 4k recording I still think a little bigger drone is easier to get jello-free. But for exploration and fun this 2 inchers are really nice.
Hello there im kinda new in this but, i had dji avata before and i bought a PAVO20 as u guess, so now i did the 90% of the work i binded all the devices and applied betafly settings. I watched lot of videos but didnt get the right answer yet. So the problem is when i try to arm the drone its closing and opening again. Its resetting itself. While it happening HD icon's bar is rising down slowly, and screen gets a red line on the bottom and right after that its closing. I gived 10 hours to make it work and i believe i deserved a little bit help. Even from now i thank you for your helpful messages.
from what i am reading, it sound like you are experiencing brown out which is a temporary drop in the voltage. (1)To rule out brown out, would you please disconnect VTX (DJI O3 air unit) and arm the Kwad. It should be able to arm without problem, and try to hovering. without the vtx connect you should be able to hover with easy. if you are unable to arm and hover without the VTX, that will mean that you have a defective AIO. Keep me updated
How do I bind my RadioMaster Zorro 4-1 to my BetaFPV Pavo 20.....looks like you covered everything but that portion unless I overlooked it? Thanks for any help!
good review, very complete shame not to have a 3s, I would like the second flight with a 3s, to have your opinion and know if the difference and flagrant.
I'm a little confused. Are you trying to connect the DJI R2 to the Pavo? If yes, you will need to connect the Rx pad on the link to an open UART on the Pavo flight controller.. Bcs you will be binding the DJI R2 to the Link Rx. Have you had time to check out Mangorille video on binding the DJI R2 to the Vista. The Runcam Link is a Caddx Vista. They just use different names but they are the same
actually what i wanna do is wiring all the 6 cables of the conector in the link, but i am going to use them with the elrs rc to piliot the drone. there is any problem to do this? or i need to wire just 4 wires (vtx) to be able to use the erls rx. tnks for your awser!@@GBoniFPV
@@GBoniFPV I am putting together the same build. Pavo20, Vista Polar. I am fairly new so knowing the Runcam and Vista are similar is good information. I plan on using the DJI R2 at the moment as I don't have a ELRS radio. Do I need to do anything to disable the onboard ELRS while using the R2? Great video. Glad I found it.
When i do a motor test in beta everything seems to spin correctly and the motors push the direction they should when moving the stick but soon as i try to take off without betaflight hooked up it gies haywire
(1) recalibrate your gyro, and make sure kwad is moving according on the setup tab (2) makes sure motors' directions are a match the direction in the motor in the motor tab on BF. (3) makes sure prop are in the correct orientation based on the motor spinning direction These steps should get you flying. Please let me know
@GBoniFPV ok so I got the gyro working like it should on the screen, motors test fine in betaflight but when trying to actually fly the front sucks down when the back should be pushing and no throttle
@GBoniFPV before the gyro fix everything worked as it should in the right stick but soon as throttle was applied it flipped, however all motors pushed correctly then
@@GBoniFPV Got my gyro set and moves correctly, props on correct, motors move fine in betaflight but when trying to actually fly the front sucks down when the back should be pushing and no throttle, all the motors and throttle worked correctly before the gyro adjustment but would flip on takeoff, please help!
hi...maybe someone could help...i do not know how to BIND with my Radiomaster...this is weird...and i have seen 2 vidos - both with a lack of information how to bind...
@WhitCoburn There are some scalable parametric box models on printable. I've made several of them. 3d printer was one of my best investments and mine runs constantly.
Hello, good day, thank you very much for your videos and your time, I bought the pavo20 and have been trying to configure it following your recommendations, but in betaflight when I try to update the firmware, I always get several errors: (###ERROR IN resource: INVALID RESOURCE NAME: 'SONAR_TRIGGER'### ###ERROR IN resource: INVALID RESOURCE NAME: 'SONAR_ECHO'### ###ERROR IN resource: INVALID RESOURCE NAME: 'SDCARD_CS'### ###ERROR IN resource: INVALID RESOURCE NAME: 'SDCARD_DETECT'### ###ERROR IN set: INVALID NAME: sdcard_detect_inverted = ON### ###ERROR IN set: INVALID NAME: sdcard_mode = SPI### ###ERROR IN set: INVALID NAME: sdcard_spi_bus = 2### ###ERROR IN set: INVALID NAME: osd_rssi_dbm_pos = 2464### ###ERROR IN save: ERRORS WERE DETECTED - PLEASE REVIEW BEFORE CONTINUING### ###ERROR IN save: PLEASE FIX ERRORS THEN 'SAVE'### and I can't link the drone and the dji controller2, is it possible that you can help me with this? thank you so much
You do not t need to update the firmware. It is an option, but this is a 2-inch drone running Betaflight. The drone is set up from the factory. It will only drink headaches if you update the firmware. In regards to binding it with to DJI FPV controller 2. It requires a couple of steps , and it will be hard to go over it in the comment section. You need to look for this video on UA-cam. " Why won't my Dji FPV contorller 2 work with the Caddx vist" by Mangorille. It is a great video, and it should help with your binding issue
Nice to see how this performs on 2s. So far, reviewers have only shown 3s, but if I were to buy this one, I'd definitely use both 2s and 3s. That prop-wash was nasty though. lol Great video.
good review, normally you just see with O3 so its nice to see with the vista as i guess still many use that one
I have a couple of builds with the O3, but I am mostly still rocking the Vista on most of my builds. The 03 has nothing on the Vista except for the 4K.
Thanks for showing the ELRS V3 target, I was unsure if the BETAFPV AIO was the right one. 🎉
No problem 👍
thanks for this vid man, everyone builds it with the o3. I feel vista is great for the pavo because if i crash it i wont cry.
That is why I used a vista., and also I don't really care much about 4K recording
Thanks for doing this video, really helped me with my setup.
U are welcome
Thanks for this video! As you said, it would have been easier to assemble without filming. Probably this is why there are not too many detailed build videos where you can really see all the details of a build from all angles. I have a mobula 8 with the vista air unit, but the pavo 20's pusher configuration is tempting me. For 4k recording I still think a little bigger drone is easier to get jello-free. But for exploration and fun this 2 inchers are really nice.
Hello there im kinda new in this but, i had dji avata before and i bought a PAVO20 as u guess, so now i did the 90% of the work i binded all the devices and applied betafly settings. I watched lot of videos but didnt get the right answer yet. So the problem is when i try to arm the drone its closing and opening again. Its resetting itself. While it happening HD icon's bar is rising down slowly, and screen gets a red line on the bottom and right after that its closing. I gived 10 hours to make it work and i believe i deserved a little bit help. Even from now i thank you for your helpful messages.
from what i am reading, it sound like you are experiencing brown out which is a temporary drop in the voltage. (1)To rule out brown out, would you please disconnect VTX (DJI O3 air unit) and arm the Kwad. It should be able to arm without problem, and try to hovering. without the vtx connect you should be able to hover with easy. if you are unable to arm and hover without the VTX, that will mean that you have a defective AIO. Keep me updated
Quick question - Do you need to solder the VTX to FC or is it Plug and play like dji o3 air unit?
plug and play
Does it only come with horizon and angle mode, no air mode?
Thank you for sharing your setup. It really helpful
Thanks for nice video.
I suppose 3S battery from Betafpv web site. I'm wondering it can fly with 2S battery anyway.
It takes both 2 and 3s. 2s for easy flying and 3s for hard flying.
Thank you for the video! I bought one
How do I bind my RadioMaster Zorro 4-1 to my BetaFPV Pavo 20.....looks like you covered everything but that portion unless I overlooked it? Thanks for any help!
The Zorro 4-1 does not have ELRS protocol. In order to use your TX with the Pavo. You will need to add an external rx that the zorro 4-1 support.
Thanks man, I have one ordered from BetaFPV and should have it this week.....Thanks again for your help!@@GBoniFPV
Your video made me purchase this😂
Which Antenna do you use for the Vista? I want to assembly a pavo20 too.
great content bro, a question, I'm new to this and I wanted to know what is the best remote control and the best googgles for Pavo20?
What VTX system are you going yo be using ?
DJI 03 air unit @@GBoniFPV
good review, very complete shame not to have a 3s, I would like the second flight with a 3s, to have your opinion and know if the difference and flagrant.
I got some on the way. I definitely curious to see what the difference in performance will be .
this is my next quad
It is a great drone
Really helpful! Thank you☺️👍
You are welcome
Hi, your video is very good. I have a Cetu X i'd like to know I can to use my googles to pilot o Pavo 20. Can you help me?
Yes, it will work with the Cetu X goggle. However, you will need to add an analog VTX and camera to the Pavo 20.
@@GBoniFPV , Would it then be easier for me to use the glasses and DJI FPV Control?
Can you stabilize the footage from the SD Card in gyro flow?
not with the VISTA, you may be able to use gyro data from the FC
Hi! The altitude hold doesn't work on my Pavo20, although the baro works. Does this feature work for you?
It is normal. Betaflight doesn't support altitude mode. The only available flight modes are Acro, Horizon, and Angle.
can i soldering the 2 wires from the dji controller in the runcam link even if i wont use them? tnks
I'm a little confused. Are you trying to connect the DJI R2 to the Pavo? If yes, you will need to connect the Rx pad on the link to an open UART on the Pavo flight controller.. Bcs you will be binding the DJI R2 to the Link Rx. Have you had time to check out Mangorille video on binding the DJI R2 to the Vista. The Runcam Link is a Caddx Vista. They just use different names but they are the same
actually what i wanna do is wiring all the 6 cables of the conector in the link, but i am going to use them with the elrs rc to piliot the drone. there is any problem to do this? or i need to wire just 4 wires (vtx) to be able to use the erls rx. tnks for your awser!@@GBoniFPV
@@GBoniFPV I am putting together the same build. Pavo20, Vista Polar. I am fairly new so knowing the Runcam and Vista are similar is good information. I plan on using the DJI R2 at the moment as I don't have a ELRS radio. Do I need to do anything to disable the onboard ELRS while using the R2? Great video. Glad I found it.
When i do a motor test in beta everything seems to spin correctly and the motors push the direction they should when moving the stick but soon as i try to take off without betaflight hooked up it gies haywire
(1) recalibrate your gyro, and make sure kwad is moving according on the setup tab
(2) makes sure motors' directions are a match the direction in the motor in the motor tab on BF.
(3) makes sure prop are in the correct orientation based on the motor spinning direction
These steps should get you flying. Please let me know
@GBoniFPV ok so I got the gyro working like it should on the screen, motors test fine in betaflight but when trying to actually fly the front sucks down when the back should be pushing and no throttle
@GBoniFPV before the gyro fix everything worked as it should in the right stick but soon as throttle was applied it flipped, however all motors pushed correctly then
@GBoniFPV and props are correct, it's a props in quad, pavo20
@@GBoniFPV Got my gyro set and moves correctly, props on correct, motors move fine in betaflight but when trying to actually fly the front sucks down when the back should be pushing and no throttle, all the motors and throttle worked correctly before the gyro adjustment but would flip on takeoff, please help!
Is it possible to dim the led? I think it is too bright sometimes.
I don't think so, but you should be able to turn off/on
yeah, on/off I put on a switch. I like the idea to turn the led on to find the quad easier after a crash.
How to rise up throttle power? So bad with almost 60% throttle
I was using a 2s lipo. This drine is really optimized for 3s. I posted the videos of this drone on 3s. It is amazing on 3s l.
hi...maybe someone could help...i do not know how to BIND with my Radiomaster...this is weird...and i have seen 2 vidos - both with a lack of information how to bind...
I quickly covered how to bind the rx to the tx in this video. That didn't help?
Can pavo 20 use vtx+analog cam ?
Yes, but you will have to be creative to install an analog vtx.
Yeah, i think because pavo20's aio FC only has digital pin for vtx
yes you can but you will not have osd then
Great review. Do you know of any good cases for the Pavo20? Thanks!
Do you have a 3D printer?
I'm not aware of one, but as suggested by BentRim, if you own a 3d printer, you may design one and print it.
Not yet. But good idea.@@BentRim
@WhitCoburn There are some scalable parametric box models on printable. I've made several of them. 3d printer was one of my best investments and mine runs constantly.
What are your rates here if you dont mind me asking?
My rates are very low. On BF, I used the KISS rate.
Roll ; 0.90/0.65/0.10
PITCH; 0.90/0.65/0.10
Yaw; 0.90/ 0.64/ 0.10
Thank you very much im just now getting into FPV@@GBoniFPV
thank you so much
2s de cuantos mah?
750mah
@@GBoniFPV gracias, muy buen video
👏👏👏👏
19:59 😂
Hello, good day, thank you very much for your videos and your time, I bought the pavo20 and have been trying to configure it following your recommendations, but in betaflight when I try to update the firmware, I always get several errors:
(###ERROR IN resource: INVALID RESOURCE NAME: 'SONAR_TRIGGER'###
###ERROR IN resource: INVALID RESOURCE NAME: 'SONAR_ECHO'###
###ERROR IN resource: INVALID RESOURCE NAME: 'SDCARD_CS'###
###ERROR IN resource: INVALID RESOURCE NAME: 'SDCARD_DETECT'###
###ERROR IN set: INVALID NAME: sdcard_detect_inverted = ON###
###ERROR IN set: INVALID NAME: sdcard_mode = SPI###
###ERROR IN set: INVALID NAME: sdcard_spi_bus = 2###
###ERROR IN set: INVALID NAME: osd_rssi_dbm_pos = 2464###
###ERROR IN save: ERRORS WERE DETECTED - PLEASE REVIEW BEFORE CONTINUING###
###ERROR IN save: PLEASE FIX ERRORS THEN 'SAVE'###
and I can't link the drone and the dji controller2, is it possible that you can help me with this? thank you so much
You do not t need to update the firmware. It is an option, but this is a 2-inch drone running Betaflight. The drone is set up from the factory. It will only drink headaches if you update the firmware. In regards to binding it with to DJI FPV controller 2. It requires a couple of steps , and it will be hard to go over it in the comment section. You need to look for this video on UA-cam. " Why won't my Dji FPV contorller 2 work with the Caddx vist" by Mangorille. It is a great video, and it should help with your binding issue
@@GBoniFPV I found the video too. Should be pretty straight forward to setup. Can't be too much different than a O3?