I believe Denso is the original manufacturer that Nissan uses for their Oxygen sensors. Alot of issues could cause an 02 code such as an exhaust leak or bad cat.
Yes Denso can be found in any store like autozone or even amazon the one we pulled was purchased from an auto parts and it only said Denso and the original from factory says Denso by Nissan I’m sure there are two versions of this sensors
@@GeorgeNava37 It's the same part. If it says by Nissan you're just paying extra for them labeling it by Nissan. Dealerships will sometimes buy from the local auto parts store and sell it to you as OE if it's the OE manufacturer.
Aftermarket are actually a better buy vs the OEM. OEM go out asmich as the aftermarket do. Difference is OEM does not come with a warranty vs after market does.
For the car on this video, may i know if the car's coil packs (not spark plugs) have been replaced? and what were the symptoms that the car needed 4 camshaft position sensors replaced?
Exactly i got a code also p0021 bank 2 vvt camshaft position, and it made some noises like almost tapping when accelerating… im tryna figure out the same thing if the motor is done or if i replace that and good togo… just ordered the part gonna see if it fixes the motor noises 😂
@@uwkcal bro nahh wait My car ticking right now with RPMs and cut off idk if I should change them because these codes (P0340,P0335,P0345)Came up on scanner before the ticking,lmk if it worked for you🙏🏼I might get a swap again but if this worked for you I am willing to try Thanks in advance
@@tonydelgado1550 didnt work for me!! It ended up being spun bearing!! I just did the motor q50 swap at infiniti dealer!! Check my latest videos I literally just finished!! With the G37s!
My car was in limp mode found out the cause was camshaft position sensor so I bought the original oem sensor and it still in limp mode I put an aftermarket one really cheap one and it works but if I floor to the ground it goes into limp mode also the harness is broken you think I should I should replace harness ?
Hey bro nice video. Was reading some trends when some people changing there sensor's on a g37 there car would only crank but not start. Did your brother have this problem and what mileage did he change them 🤙🏾
I didn't have a problem necessarily, my mileage on the car at the time being was at 80,000 and was wondering when to change the cam positioning sensor out before the problem even begins.
I changed my value covers , spark plugs and coils ... I don't have a code for camshaft but my vdc and slip is on and my car jumps now didn't before the change
Car goes into limp mode and my vdc light and slip light are on also but it's not throwing a code ? Could it be the camshaft sensors ? I don't wanna waste money on them for nothing
@@GeorgeNava37 its still there soon as I start the car all the lights automatically turn on.. I been doing some research and I'm thinking it could be a fried ecu or it needs to be reprogramed 🤧
Mines doing the same did you find a fix?? My slip and vdc turns on sometimes mostly a cold start then id shut it off for 5 min then they disappear till another cold start
I have a check engine light and I checked it and I found camshaft A & camshaft B, Do u think I have same issue of ur brother G ? " G35 2008 sedan twin throttle body ".
I got the same car and mines show me p0340 bank 1 or single one but it shows me twice like two sames codes???? So that’s mean i have to change it all of them ?
@@MStromboli Yes, but it was not my sensor that was the problem. Sad and long story short, I ended up selling my G35 dirt cheap, and the guy I sold it to won big time! He said all it needed was a timing relearn on the exhaust. All that money I put into and struggle for nothing. 💔
Sometimes a camshaft sensor can trigger different codes depending how old your car is and mileage might as well replace them all if that doesn’t change then you would know it’s not the camshaft sensor
I called infiniti dealer they said my 2013 g37 on has 2 camshaft position sensors is this right??? But i has who is the manufacturer he said nissan i have a feeling maybe denso makes them for nissan
When it comes to camshafts it’s always good to replace all of them might as well if car doesn’t start try putting old one back maybe another camshaft is bad
i just changed my valve covers, coils, spark plugs, test pipes,y-pipe, and 02 sensors and now my car stutters when pulling off as it passes 1k rpms and when stepping on it and stalled out (shut off)on a red light. any thoughts.. no check engine light tho
Theres actually 4 cam shaft position sensors an theres only 2 codes for them 0011 an 0021 an it says bank 1/2 then bank 1/2 again for the others so theres a total of 4 sensors on a vq35hr
@@bigfradoe2934 mine was giving a crankshaft sensor error code , bought a new sensor from the dealer and code went away car runs normally now , Do you have the code ?
@@christianreyes6372 the code is giving me p0340 bank 1 my takes 4 seconds to start up & won’t accelerate over 20mph it just starting acting like this , I cannot find bank 1 camshaft sensor
@@vqchunx I replaced the driver side Variable valve timing position sensor not the camshaft sensor. VVT sensor are located in front of the engine. Passenger and driver side.
I believe Denso is the original manufacturer that Nissan uses for their Oxygen sensors. Alot of issues could cause an 02 code such as an exhaust leak or bad cat.
Yes Denso can be found in any store like autozone or even amazon the one we pulled was purchased from an auto parts and it only said Denso and the original from factory says Denso by Nissan I’m sure there are two versions of this sensors
Denso is also a Nissan original.
@@GeorgeNava37 It's the same part. If it says by Nissan you're just paying extra for them labeling it by Nissan. Dealerships will sometimes buy from the local auto parts store and sell it to you as OE if it's the OE manufacturer.
Yeah thats true, denso is infinitis brand, i get plugs, and o2 sensors from denso
Hitachi is the original sensor
Aftermarket are actually a better buy vs the OEM. OEM go out asmich as the aftermarket do. Difference is OEM does not come with a warranty vs after market does.
Well done how many camshaft position sensor are there?
3 !
My infiniti g25 have 4 cam sensor 🤨
What kind of problems did he have with fault cam sensors?
For the car on this video, may i know if the car's coil packs (not spark plugs) have been replaced? and what were the symptoms that the car needed 4 camshaft position sensors replaced?
What yr is yours? Looks different than my 12 g37s... cant find them
So for the G35 sedan and G37 sedan is the same?
Quick question bro? Before you replaced all the sensors how did the car run before?
Exactly i got a code also p0021 bank 2 vvt camshaft position, and it made some noises like almost tapping when accelerating… im tryna figure out the same thing if the motor is done or if i replace that and good togo… just ordered the part gonna see if it fixes the motor noises 😂
@@uwkcal bro nahh wait My car ticking right now with RPMs and cut off idk if I should change them because these codes (P0340,P0335,P0345)Came up on scanner before the ticking,lmk if it worked for you🙏🏼I might get a swap again but if this worked for you I am willing to try Thanks in advance
@@tonydelgado1550 didnt work for me!! It ended up being spun bearing!! I just did the motor q50 swap at infiniti dealer!! Check my latest videos I literally just finished!! With the G37s!
My car was in limp mode found out the cause was camshaft position sensor so I bought the original oem sensor and it still in limp mode I put an aftermarket one really cheap one and it works but if I floor to the ground it goes into limp mode also the harness is broken you think I should I should replace harness ?
Did you ever fix the problem ?
How many crankshaft and camshaft needs a g37?
Great video. Anyone know a great mechanic for a 2009 G35?
Hey bro nice video. Was reading some trends when some people changing there sensor's on a g37 there car would only crank but not start. Did your brother have this problem and what mileage did he change them 🤙🏾
hey bro did you ever find out what your problen was?
I didn't have a problem necessarily, my mileage on the car at the time being was at 80,000 and was wondering when to change the cam positioning sensor out before the problem even begins.
I changed my value covers , spark plugs and coils ... I don't have a code for camshaft but my vdc and slip is on and my car jumps now didn't before the change
Hey man what brand is the sensor and from where did you get it I’m
Not trynna buy a bad sensor
OEM from Infiniti dealer had bad experience purchasing autozone sensors 🤷🏻♂️
@@GeorgeNava37 I have the code p0345 where is that sensor located?
Where can I get the sensor to purchased
Car goes into limp mode and my vdc light and slip light are on also but it's not throwing a code ? Could it be the camshaft sensors ? I don't wanna waste money on them for nothing
Sometimes all you need to do is a reset unplug your battery for about 10min and see if problem still there
@@GeorgeNava37 its still there soon as I start the car all the lights automatically turn on.. I been doing some research and I'm thinking it could be a fried ecu or it needs to be reprogramed 🤧
Abs sensor
Mines doing the same did you find a fix?? My slip and vdc turns on sometimes mostly a cold start then id shut it off for 5 min then they disappear till another cold start
is v36 g37/g35's OEM brand "Hitachi" for the 4 camshaft position sensors?
What is bank 1 position george.. my infiniti sensor cmp fault😢
thanks george for th video!~
I have a check engine light and I checked it and I found camshaft A & camshaft B, Do u think I have same issue of ur brother G ? " G35 2008 sedan twin throttle body ".
أديب / Adeeb yes at this point it would be better to change all 3 sensors
I'll send a pic of issues in instagram.
We're you able to replace sensors?
I got the same car and mines show me p0340 bank 1 or single one but it shows me twice like two sames codes???? So that’s mean i have to change it all of them ?
did u have any symptoms of bad camshaft sensors?
Bro is it a specific spot for each sensor? Meaning the one on the valve cover A and B. What if i switch them by mistake or the wires?
?
How many camshafts sensors are there and crankshaft sensors ?
What were the symptoms
did you try just cleaning them.. maybe with maf cleaner or something? is that possible?
Hey do all 3 sensors look the same for the camshaft position sensor?
Bank 1 is streght bank 2 is alil curve
I replaced my camshaft sensor but still have the same problem I think is a fuse you know ware the fuse is located for the camshaft sensor
Are they 3 the same? I just found one
I need to replace bank 2 is that only 1 ? And which One would it be ?
Nice video! I'm having a p0014 code. Which one do I replace?
Did you figure this out?
@@MStromboli Yes, but it was not my sensor that was the problem. Sad and long story short, I ended up selling my G35 dirt cheap, and the guy I sold it to won big time! He said all it needed was a timing relearn on the exhaust. All that money I put into and struggle for nothing. 💔
how many sensor u put in 2 on each side
Another great one brother..👍👏👏👏 I should be ok for awhile. Mines a 12 like yours, with about 43k on the clock
Nonameisthename 1 nice bro then no worries on those for now 😅
Do you push the tab on the plug to remove the sensor from the wiring connector? I’m having issue removing it buy pushing the tab.
What brand of crankshaft position sensor did you use? Tryin to find the best and on the cheap cheap bro.
Call the dealer bro i did all they said was its nissan but i feel denso makes them for them
I found some on rockauto.com 🤙🏽
Your infiniti is dope.... my censor a jyst wrnt out ugh
Where can I get the OEM? Do I go to Infiniti’s dealership?
Correct at infiniti dealer
Bro I changed my crank sensor and the code still was there .Took it to a shop they they it’s the cam sensor but I don’t get that code.
Sometimes a camshaft sensor can trigger different codes depending how old your car is and mileage might as well replace them all if that doesn’t change then you would know it’s not the camshaft sensor
If I change one do I have to change all?
No not necessarily you can use a code reader and find which one is bad and you be good by changing bad sensor 👍🏼
Yes you have to or they will all go out again
I called infiniti dealer they said my 2013 g37 on has 2 camshaft position sensors is this right??? But i has who is the manufacturer he said nissan i have a feeling maybe denso makes them for nissan
Do you plan on tuning your g?
Henry Figueroa yes that is the plan 🙏🏼
HEY BRO, I HAVE A 08 350ZHR, ARE THESE THE SAME CAMSHAFT SENSORS AND LOCATIONS?
Are they the same? Did u figure it out? Cause i need to change mine 😭
@@rothebest2010 yes
i changed out one of them and now the car wont start any ideas, tips
When it comes to camshafts it’s always good to replace all of them might as well if car doesn’t start try putting old one back maybe another camshaft is bad
Good looks bro. Every other video was the coupe replacement. Seems easy enough with two ppl.
Aye bro where did u buy the sensors at
Saul Ochoa from Infiniti dealer
I am getting ready to change out my sensors, Lets see how easy this is....
how was it did it work?
Do all Latinoz over-tighten everything? From what I see yeah! How many uga dugaz was that, 80nm?
yup, the same way white people dont use seasoning!
yup, the same way white people dont use seasoning!
I must be blind because on my g37x 2011 sedan i do not see these sensors but i gave a code for cam sensor postion a bank 1
Same did you figure it out? Or you still have the problem
Camshaft bank 2 is located next to the timing cover? Driver side?
Did you find out which one was bank 1 and bank 2
i just changed my valve covers, coils, spark plugs, test pipes,y-pipe, and 02 sensors and now my car stutters when pulling off as it passes 1k rpms and when stepping on it and stalled out (shut off)on a red light. any thoughts.. no check engine light tho
@Federal Bureau of Investigation yea i have..but i have a question..what kind of person names themselves the federal bureau of investigations lol
@@GhostOfBrickCityGaming what fix it having same problem
Wats the best solution for a p0300 on the g35?
Is the location different in a 2013 g37x?
What sensors are the ones in the front? On each side aren't those camshaft sensors too?
Those are variable timing actuators on the front of the engine.
I dont have this space behind my engine
You guys should change that bleeder vowel
What sensors you replace in the back lol
What's the PART #'s
Theres actually 4 cam shaft position sensors an theres only 2 codes for them 0011 an 0021 an it says bank 1/2 then bank 1/2 again for the others so theres a total of 4 sensors on a vq35hr
is it normal for my car to go into limp mode because of the faulty sensor ?
Having the same issues I have a 2009 g37x sedan keep saying bank 1 cam shaft sensor
@@bigfradoe2934 mine was giving a crankshaft sensor error code , bought a new sensor from the dealer and code went away car runs normally now , Do you have the code ?
@@christianreyes6372 the code is giving me p0340 bank 1 my takes 4 seconds to start up & won’t accelerate over 20mph it just starting acting like this , I cannot find bank 1 camshaft sensor
Did you ever find a solution to this? I changed my bank 1 camshaft sensor and it went I to limp
@@StockM56 my car went to limp because of the sensor, went ahead and changed the crankshaft sensor . CEL went away car was back to normal.
I got a p0024 cam sensor maybe
Which driver side bank 2 sensor is the P0021 code coming from? The upper one or the lower one (driver side bank 2)
Thanks!
did you ever find out i’m having same thing
@@vqchunx I replaced the driver side Variable valve timing position sensor not the camshaft sensor. VVT sensor are located in front of the engine. Passenger and driver side.
The one on the passenger side is a crankshaft position sensor
Bro idk I always buy my stuff in 1A auto and shit is cheaper and oem quality ngl
The camshaft position sensors for a VQ35HR are like $30 in there rn
does it have 2 or 4 cause i looked at mines and there are 2 on each side of the engine same part also? wtf
2
Well shit I wish I would have watched this first😣 I just bought them from AutoZone
Hell, there's 3 cam sensors?
Cloud Victorious ikr I’m like damn!!
How to known what side is bank 1?