These sort of videos are worth their weight in gold..... It would be unfair to call it a compilation video as it highlights so many useful tips that can be easily missed in the build episodes. I particularly enjoy both the ‘smug’ “of course I know that” moments and the lightbulb moments of “why don’t I know that” or “of course it’s so obvious why didn’t I think of that” Thank you great content as always, Peter.
Thanks Iain! Yes, it was suggested by a Patreon supporter actually, this kind of format - if it was on TV we'd call it 'revisited' - and there may well be more of this type to come. 👍
Nice one matey. I have one for you since you asked. You can cut 3 or 4 or more boards with only one pencel mark on the first one by placing them on top of each other than make the first board and cut only the top board and after you remove the scrap the blade would have left a scoreline on the next board for you to follow, and so on. (Building site trick mostly used for battens and joists but works with any cut)
Yes I have been cutting a full bevel on an oversized piece then the straight 90 degree cut. This way seems both easier and more consistent for prices that join together
Being a professional cabinet maker and installer, this is the most comprehensive how to tricky cutting with a track saw. I just need to figure out the best combination of bench, bench dogs and accessories to have when working in the field where table saw and miter saw is not practical and a track saw needs to perform the same functions. Thank you for the video!
That’s kind of you to say, but I’ve been practising for ~20 years and still make some terrible mistakes! I don’t think anybody really gets any better - exist eg better at hiding the mistakes! 😂👍👍
I've been contemplating buying a track Saw instead of a table saw, this has cleared up all the worries I had about a track saw. Thanks Peter! Great video as always!
Great tip on taping the thin piece to a wider piece, I had been not using stock once it got thinner than about 6”, will def be giving the tape trick a try on my next go round!
Peter, you ought to make a video for geometry teachers to show their students that illustrates, “Yes, it is indeed quite possible, you may use this again.” So relevant. Thank you so much!
Well watching all the jobs you do with a Track Saw and mft table you have convinced me I only have a very small workshop no room for a table saw!! thanks Peter love your video's.
Thanks. Peter. I have bought enough Festool tools thanks to you and Peter Parfitt. Such a useful video which puts off a Kapex purchase for a bit longer. Great channel
I couldn’t agree more about your comments on the Strawbyte jig. I seem to use it daily. I’m a left handed lad and tend to “see” the job the other way round from you right handers and naturally want to have the waste on the left of the track rather than the saw side. That little jig is a game changer in terms of accuracy. Loads of other good stuff in the vid as well, as per….
Good Stuff. Cutting French cleats this way was one of the first things I did after getting my track saw. So far I haven’t come across a cut that I need which would require a table saw. Those waste side jigs are great. I got them based on your video and not disappointed at all.
Just when I need to know something, you make a video about it. Its like you can see into my brain and you know what help I need. Thank you Mr. Millard. This was extremely helpful!
Cutting ply or working with ply is my favourite material I like working with. I notice at around 6 minutes after doing the angle cut you were limited for space and a slight burn mark near the end of the material you cut. I think that's because you didn't have enough space after the cut or you will hit vacuum hose. Your attention to detail and perfection is on another level. Great video.
@@10MinuteWorkshop i remember the video where you first mentioned that you were gonna stop this and I thought: oh why oh why. At the same time I was starting a big remodeling job of my new home office at the end of which I thought: I understand now why he stopped 😂
Really happy I found your channel! The video on tricky track saw cuts was a real life saver. I've just bought a dewalt model so learning what it can do and how to use it. I was really stuck on a project for cutting bevels smaller than the track width and saw (huh) how you supported off the edge. Its always obvious after you watch someone doing it (hahaha). Can now finish project. Thank you
Hi Peter Interesting video mate liked that.. Plus the simple way to make wedges, I love my festool plunge saw id be lost without it I tend to use it on most of my jobs great video mate thank you 👍👍👍👍
Thank you - It's time for me to advance my Festool track saw applications. I would very much appreciate a list of track accessories. You have provided a confidence boost to give it a go. Greetings from Downunder
Thanks Geoff! A lot will depend on what you want to do with it, and wether you have an MFT bench or MFT top, and also not sure what's available down under, so excuse me if I reply in generalities, rather than specific brands? If you have an MFT then benchdogs are a must, a fence & flagstops very useful to have. A rail hinge is very useful, but the Dave Stanton dog locks are a great product and take up less space - and cost less too! Some horizontal clamps are very useful for holding things down - been using the Bessey ones (featured in my recent Gifts List video) and they work very well, without lifting the workpiece. If you don’t have an MFT then a rail square is very useful, either bought or made, and / or parallel guides really help if you need to make regular rips of a consistent width. And rail clamps of course - always room for rail clamps, especially when any kind of a slip-up would be expensive! Other than those, I think how you’re planning to use the saw would determine the best accessories; if you can give me some idea of that then I can probably come up with a few others, OK? Hope that helps and thanks again! Peter
Absolutely fantastic stuff! Oh how I could have done with this a couple of days ago when cutting French cleats for my shelf on your mobile bench build. Couldn't stop the piece moving. Tape it to the supporting piece! So obvious now! Took me 2 hours and many 'practice' cuts to get just 2 pieces done so at least I know how to do the others now. Thank you so much.
Love the tips. Personally I use track clamps with my rail... handy with small irregular cuts that are too long for my mitre saw. But I also like your setup.
Another Awesome Share of your experience and knowledge Peter , you make it looks so easy , after a couple of tries on some scrap and taking it real slow the outcome is Pretty great , again thank you so much
Great stuff, thanks Peter, like you I love my track saw and use it daily, however many of these cuts would be far easier on a table saw,(not that I have one or the space for one!)thanks again and stay well,
Well, that’s the point really - they may be ‘easier’ on a table saw, but if you don’t have one or have space for one, or the budget for a decent one, then these cuts can be done, safely and easily. 👍👍
As voiced by others, since purchasing my track saw I seem to find more uses for it. I love the safety aspect for cutting sheet material and thin strips. I have the 36v Makita but am thinking about adding a corded version on the Festool, Makita and Triton track system. When I am working away from my shop, nothing beats a cordless tool. IMHO. But, in the shop having the cord attached to the hose is really pretty efficient. I am going to order some of the makita Strawbyte waste side jigs. thanks for the tips on the partial bevel cuts. keep up the great videos I always learn something. Thanks Peter.
Taping the support piece to the bit you're cutting is a good idea. I had a kickback incident trying to make a small cut off the side of a thin piece. I had a support beside it under the track but was leaning over the saw to see where to stop the cut and think I must have put some sideways pressure on the saw, the piece was able to shift and catch the blade. it was pretty scary, happened instantly and put a big gouge in my track. I think taping the bit being cut and the support together would have stopped it. (Also note the 'grippy' strips on the bottom of the makita track are quite far away from the cut). Lesson learned I hope.
Bit more info, this was an Erbauer saw on a 1.5m Makita track. The adjustment knobs are at their limit and I'm not 100% happy that there's no side to side movement of the saw on the track. Also the Festool riving knife would probably have stopped this happening. The 'safety' dilemma now is whether to upgrade to the Makita saw, or Festool. :-)
Ooch! Can give you a bit of a 'moment' if that happens! As I say in the vid a bevel cut is the one where I always recommend clamping the rail and the workpiece. Erbauer is a nice saw, but the Festool is a significant step up (from the Erbauer and the Makita, IMHO) if you can swing the extra £££. 👍
A wedge jig like that track saw crosscut jig you made years ago would be very useful. It could have an adjustable stop. Would be nice to have on an install if you need more or a custom sized wedge
I had to watch this one twice, after watching it two times. I bought my rails used. That way I can pretend that little arc of shame at 7:00 was not mine.
@@10MinuteWorkshop Peter, I know exactly how you feel. I loaned my wife only out once, after that she's never been the same. Never again! 🤦♂️ Terrific tips! I bought my track saw after my table saw, so just to keep it from getting jealous, I do most those angle/bevel cut on it. Although, on smaller pieces the track saw does work a bit better. 👍
@@10MinuteWorkshop not really going to do it tonight but I will certainly make a few now as I so often need wedges for doors and just to lift something a tiny bit incrementally etc. etc. It is too dangerous to do this on my mitre saw so, since I have been hankering over a track saw for a while, maybe this is the time to get one... just to make a few wedges and keep my fingers! Anyway, I am up at 5 so best skedaddle orf to my slumber platz... I recommend the same for you at this unearthly hour btw!😂😂
Hi Peter, awesome video as usual 👍. As a novice, making cuts with the track saw, on thin materials always worries me, as I didn’t really know the best way to achieve it. I was almost considering purchasing a job site track saw, pretty much for just that, as I don’t have a workshop. But you have now given me more confidence in using my track saw (Makita) and rails for doing this, especially as I love using my folding MFT workbench that I built with your plans. The only thing I need to find now, is a shorter piece of track, as my 1400mm long pieces are a bit of a nightmare at times. I think Makita do a 1000mm length, so may go for that. Also, after watching your videos I purchased the BenchDogs Guide rail set, and will be getting their Square. Keep up the amazing work, love watching your video with Denis from Hooked on Wood as well. His workshop looks amazing!
As always, really well made and very useful video for the track saw users out there. I had wondered if there’s a safe way to make tapered legs using a track saw? It’s something I’ve seen done many times on a table saw, but it would be great if there was a way to do it without having to go down that particular route. And every way I can think of doing it with a track saw seems precarious, at best!
Excellent video. With a track saw and an MFT type system, you can do most things a table saw can. One that stumps me is how to do an angled cut along the face of a board, as with a door threshold that has a slight ramp. On a table saw, you would put the board against the fence vertically. The blade would have a slight angle away from the fence. Any idea if this type of cut is possible with a track saw plus your typical MFT type jigs?
Fabulous content ! great delivery and clear VALUE . Know wonder you are living your dream. Now please tell me what camera and lighting you use . I' m just starting out with a track saw and love it. I hope to use video to explain and demonstrate my design patents to market my ideas to manufactures .Learn from the best! Thank you so much ! I am going to look at ALL your videos !!!
Thank you! I mostly use Panasonic LUMIX cameras (GH5 and G80) a GoPro 9 and my Phone. Rode microphones have worked well for me. And lighting is just from LED panels in the ceiling - I’m about to replace them, it they’ve lasted pretty well. Hope that helps! Peter. LED panels - ua-cam.com/video/TrukKsGFGO8/v-deo.html
The large Festool HK saw will bevel at 60°, otherwise the only way I know is to chock the rail up with wedges. It’s not something I needed to do a lot, but if I did I’d make a bevel platform of some kind. 👍
Wow, the Strawbyte jigs look cool. I'm in the U.S., so I'm not sure I can buy from their website. They do sell them on Etsy in the U.S., so I just ordered some.
What am I missing re. partial bevel cut Peter - surely if using 45 degrees, the distance you overhang the track by is the same distance down from the top surface that you wish the bevel to start, as it makes a right angle isosceles triangle? Merry Christmas! 🎅🏻
![My 5 Worst Buys! [video 484]](http://i.ytimg.com/vi/5uoQ78879Es/mqdefault.jpg)
![My 5 Worst Buys! [video 484]](/img/tr.png)
![Pocket-money Rail Hinge [video 497]](http://i.ytimg.com/vi/sHj5G6t1qvY/mqdefault.jpg)
![Cheap & Easy Tracksaw Mitre Jig [Video 513]](/img/n.gif)
“Tricky cuts with many easily resolved with nothing more than sticky tape” - Blue Peter Millard. Super helpful video as always. 🙏
Matthias Wandel is the wizard of table saw on youtube, and you are wizard of track saw.
These sort of videos are worth their weight in gold.....
It would be unfair to call it a compilation video as it highlights so many useful tips that can be easily missed in the build episodes.
I particularly enjoy both the ‘smug’ “of course I know that” moments and the lightbulb moments of “why don’t I know that” or “of course it’s so obvious why didn’t I think of that”
Thank you great content as always, Peter.
Thanks Iain! Yes, it was suggested by a Patreon supporter actually, this kind of format - if it was on TV we'd call it 'revisited' - and there may well be more of this type to come. 👍
Simple, clear and concise. I can only imagine the amount of work that has gone into preparing for and then editing this video.
Thanks Nico! 👍
I want to like this twice. The partial bevel solution is great, I need more bench dogs and clamps.
Thanks! And we all need more Benchdogs and clamps! 😂👍
That technique for cutting the wedges is brilliant! i usually do it by eye on the bandsaw but your method is a ton better.
Thanks! 👍
The wedge making trick is really useful. Thanks Peter.
It sure is! 👍
Nice one matey. I have one for you since you asked. You can cut 3 or 4 or more boards with only one pencel mark on the first one by placing them on top of each other than make the first board and cut only the top board and after you remove the scrap the blade would have left a scoreline on the next board for you to follow, and so on. (Building site trick mostly used for battens and joists but works with any cut)
Cheers George! 👍👍
Thank so much excellent illustration I am really grateful
Nice, I like the bevel cuts at the leading edge of the bedside cabinet, they really elevate the finished product.
Thanks! Yes, the little details make the difference. 👍👍
Yes I have been cutting a full bevel on an oversized piece then the straight 90 degree cut. This way seems both easier and more consistent for prices that join together
Peter, in this video you just answered all the the questions that I had building my first night stand. thank you so very much for your content.
Thanks Alexander!
Being a professional cabinet maker and installer, this is the most comprehensive how to tricky cutting with a track saw. I just need to figure out the best combination of bench, bench dogs and accessories to have when working in the field where table saw and miter saw is not practical and a track saw needs to perform the same functions. Thank you for the video!
I have to watch this maybe 10 times to come close to this level of skill, very impressed and feeling humble.
That’s kind of you to say, but I’ve been practising for ~20 years and still
make some terrible mistakes! I don’t think anybody really gets any better - exist eg better at hiding the mistakes! 😂👍👍
I've been contemplating buying a track Saw instead of a table saw, this has cleared up all the worries I had about a track saw. Thanks Peter! Great video as always!
Thanks! 👍
Great tip on taping the thin piece to a wider piece, I had been not using stock once it got thinner than about 6”, will def be giving the tape trick a try on my next go round!
Peter, you ought to make a video for geometry teachers to show their students that illustrates, “Yes, it is indeed quite possible, you may use this again.” So relevant. Thank you so much!
Haha, thanks! 👍
Well watching all the jobs you do with a Track Saw and mft table you have convinced me I only have a very small workshop no room for a table saw!! thanks Peter love your video's.
Thank you! 👍
Thanks. Peter. I have bought enough Festool tools thanks to you and Peter Parfitt. Such a useful video which puts off a Kapex purchase for a bit longer. Great channel
Thank you!
I couldn’t agree more about your comments on the Strawbyte jig. I seem to use it daily. I’m a left handed lad and tend to “see” the job the other way round from you right handers and naturally want to have the waste on the left of the track rather than the saw side. That little jig is a game changer in terms of accuracy.
Loads of other good stuff in the vid as well, as per….
Thanks! 👍
Good Stuff. Cutting French cleats this way was one of the first things I did after getting my track saw. So far I haven’t come across a cut that I need which would require a table saw. Those waste side jigs are great. I got them based on your video and not disappointed at all.
Thanks! Yes, great little jigs. 👍👍
Just when I need to know something, you make a video about it. Its like you can see into my brain and you know what help I need. Thank you Mr. Millard. This was extremely helpful!
Thank you! 👍
All kinds of problems can be solved by just putting a scrap piece to help support the rail on a piece thinner than the rail. Nice bunch of tips.
Cutting ply or working with ply is my favourite material I like working with. I notice at around 6 minutes after doing the angle cut you were limited for space and a slight burn mark near the end of the material you cut.
I think that's because you didn't have enough space after the cut or you will hit vacuum hose.
Your attention to detail and perfection is on another level.
Great video.
Thanks! 👍🙌
Got my waist side jigs lately, now waiting for my festool track, ordered 3 Werkstatt ago 😢
I got some of those jigs from Strawbite and sent to Australia. Lucky I put them in in a safe place as I can’t find them Damm it. 😂
Those tricks are so impressive, I am speechless.
Get it? ... Speechless.
You are such a genius!! Your ideas are absolutely great! Too bad you stopped doing furniture. Loved that as well!
Thank you. And FEIW I’m very happy to have stopped the fitted furniture side of things. 😂👍
@@10MinuteWorkshop i remember the video where you first mentioned that you were gonna stop this and I thought: oh why oh why. At the same time I was starting a big remodeling job of my new home office at the end of which I thought: I understand now why he stopped 😂
Another brilliant video. Cutting those wedges was fantastic.
Thanks! 👍
Another video for the Track Saw Bible. Thanks for sharing.
Thanks Goran! 👍
Worth every penny and shipping across the pond. Awesome little product.
Absolutely. 👌👍
Fantastic and very informative video, thanks for sharing 👍
Always enjoy watching Peter; always pick up great tips....cheers...rr Normandy, Fra
Thanks Richard! 👍
Really happy I found your channel! The video on tricky track saw cuts was a real life saver. I've just bought a dewalt model so learning what it can do and how to use it. I was really stuck on a project for cutting bevels smaller than the track width and saw (huh) how you supported off the edge. Its always obvious after you watch someone doing it (hahaha). Can now finish project. Thank you
I've been putting off buying a track saw for a long time. Think I will finally make the plunge due to this video Peter. Thanks 👍
Love the "no nonsens" channel here... And your skills...
Hi Peter
Interesting video mate liked that.. Plus the simple way to make wedges, I love my festool plunge saw id be lost without it I tend to use it on most of my jobs great video mate thank you 👍👍👍👍
Thanks for the new lesson, I learned again a lot!
Great information.I have just started as a wood working hobbyist and am learning a lot here on UA-cam. Best wishes from India 🇮🇳.
Thank you, and best wishes from London! 👍
Thanks Peter, some of the track saw cuts are tricky and what you said makes sense. Support and be safe
Thanks Doug!👍👍
Cracking tips Peter,thanks for sharing!👍👍👍👍👍👍👍👍👍😎😎😎
Cheers Allan! 👍👍
I love watching everyone of your video's
So smart Peter! Many thanks for your practical and clearly explained tips and tricks and methods.
Thank you! 👍
Thanks!
Thank you! 🙌
Always interesting to see tricks from you. Thank you.
Hi Peter, a very informative video, thank you. And another vote for the Strawbyte waste side jig.
Thanks! 👍
Thank you - It's time for me to advance my Festool track saw applications. I would very much appreciate a list of track accessories. You have provided a confidence boost to give it a go. Greetings from Downunder
Thanks Geoff! A lot will depend on what you want to do with it, and wether you have an MFT bench or MFT top, and also not sure what's available down under, so excuse me if I reply in generalities, rather than specific brands?
If you have an MFT then benchdogs are a must, a fence & flagstops very useful to have. A rail hinge is very useful, but the Dave Stanton dog locks are a great product and take up less space - and cost less too! Some horizontal clamps are very useful for holding things down - been using the Bessey ones (featured in my recent Gifts List video) and they work very well, without lifting the workpiece.
If you don’t have an MFT then a rail square is very useful, either bought or made, and / or parallel guides really help if you need to make regular rips of a consistent width. And rail clamps of course - always room for rail clamps, especially when any kind of a slip-up would be expensive!
Other than those, I think how you’re planning to use the saw would determine the best accessories; if you can give me some idea of that then I can probably come up with a few others, OK?
Hope that helps and thanks again! Peter
Absolutely fantastic stuff! Oh how I could have done with this a couple of days ago when cutting French cleats for my shelf on your mobile bench build. Couldn't stop the piece moving. Tape it to the supporting piece! So obvious now! Took me 2 hours and many 'practice' cuts to get just 2 pieces done so at least I know how to do the others now. Thank you so much.
Yeah, been there! Fortunately I’ve had a few years of daily tracksaw use to figure some of this stuff out! 👍👍
Love the tips. Personally I use track clamps with my rail... handy with small irregular cuts that are too long for my mitre saw. But I also like your setup.
Another excellent tip & well presented as always thanks Peter 👍👍👍👍
Thanks Trevor! 👍👍
Another Awesome Share of your experience and knowledge Peter , you make it looks so easy , after a couple of tries on some scrap and taking it real slow the outcome is Pretty great , again thank you so much
Thanks! And bear in mind I’ve had ~20years of practice - and I still make plenty of mistakes! 😂👍👍
Excellent video like the simple way to make wedges cheers Peter
Cheers Mark! 👍
Thanks for the great content!!
Very helpful!
One of your best videos Peter. 👏
Thank you! 👍
So simple and obvious yet still i need to have you guide me into the OH MY GOD moment of enlightenment ;-) Thanks!
🙌😂😂👍
always so educational thanks peter
Great video Peter, I love my TS-55, just use my table saw as a place to stack the systainers!
Thanks Dawn! Must admit I keep looking at my table saw and wondering why I have it. 🤷♂️👍
Thanks Pete
The wedge trick is very clever...
Thanks for these tips, I don't have space for a table saw and sometimes wonder how to achieve certain cuts with my track saw.
Thanks! 👍
Great stuff, thanks Peter, like you I love my track saw and use it daily, however many of these cuts would be far easier on a table saw,(not that I have one or the space for one!)thanks again and stay well,
Well, that’s the point really - they may be ‘easier’ on a table saw, but if you don’t have one or have space for one, or the budget for a decent one, then these cuts can be done, safely and easily. 👍👍
"...but Management decided..."
Been. Done. T-Shirt. A whole drawer full.
I watched past weeks all your YT content and is realy amazing stuff, learn a lot from it, so thank you Peter!
Thank you! 👍
As voiced by others, since purchasing my track saw I seem to find more uses for it. I love the safety aspect for cutting sheet material and thin strips. I have the 36v Makita but am thinking about adding a corded version on the Festool, Makita and Triton track system. When I am working away from my shop, nothing beats a cordless tool. IMHO. But, in the shop having the cord attached to the hose is really pretty efficient. I am going to order some of the makita Strawbyte waste side jigs.
thanks for the tips on the partial bevel cuts. keep up the great videos I always learn something. Thanks Peter.
Thanks Marty! 👍👍
Thanks Peter - very nice again.
Thanks Wino! 🙌
Great video as ever
Hi Peter
Watching you from Florida
Easy life, Michael! 😂 Hope it’s going OK 👍 👍
Another great Video Peter .... Thank you.
Cheers Nick! 👍
Thank You for this tipps! Great help for me!
love the wedges
Cheers, mate, some great tips there.👌🏽
Thanks for sharing.👍🏽
Take care.
Cheers Bill! 👍👍
Looking forward to the DIY MFT top video! I'm planning on getting rid of my small table saw and making the switch to full track saw mode
Nice! 👌👍
Oh when is this video out Peter?
When it’s ready. A few weeks maybe. 👍
Very good video.
Great tips Peter!
Thanks! 👍
Taping the support piece to the bit you're cutting is a good idea. I had a kickback incident trying to make a small cut off the side of a thin piece. I had a support beside it under the track but was leaning over the saw to see where to stop the cut and think I must have put some sideways pressure on the saw, the piece was able to shift and catch the blade. it was pretty scary, happened instantly and put a big gouge in my track. I think taping the bit being cut and the support together would have stopped it. (Also note the 'grippy' strips on the bottom of the makita track are quite far away from the cut). Lesson learned I hope.
Bit more info, this was an Erbauer saw on a 1.5m Makita track. The adjustment knobs are at their limit and I'm not 100% happy that there's no side to side movement of the saw on the track. Also the Festool riving knife would probably have stopped this happening. The 'safety' dilemma now is whether to upgrade to the Makita saw, or Festool. :-)
Ooch! Can give you a bit of a 'moment' if that happens! As I say in the vid a bevel cut is the one where I always recommend clamping the rail and the workpiece. Erbauer is a nice saw, but the Festool is a significant step up (from the Erbauer and the Makita, IMHO) if you can swing the extra £££. 👍
Very easy to imagine you as Italian during the silent bit at the end 🇮🇹
It’s the hand-waving semafore that does it. ! 😂
that saw dos everythink dos it make a cupper aswell peter lol
I'm always learning, thanks!
👍
A wedge jig like that track saw crosscut jig you made years ago would be very useful. It could have an adjustable stop. Would be nice to have on an install if you need more or a custom sized wedge
Thanks! 👍
Thank You
Pleasure! 👍
Wow - just - wow 😯
That is bloody clever stuff!
Thanks! 👍
I had to watch this one twice, after watching it two times. I bought my rails used. That way I can pretend that little arc of shame at 7:00 was not mine.
The only rail I ever lent out. Never again. 🤷♂️
@@10MinuteWorkshop Peter, I know exactly how you feel. I loaned my wife only out once, after that she's never been the same. Never again! 🤦♂️
Terrific tips! I bought my track saw after my table saw, so just to keep it from getting jealous, I do most those angle/bevel cut on it. Although, on smaller pieces the track saw does work a bit better. 👍
I think I need an MFT. I've made plenty of these cuts before but it's always more awkward than it needs to be.
Thank you!
👍
Nice use of using a stop to make the thin cuts in guessing it doesn't bind at all?
Thanks! And no, not at all. 👍
These are great tips. Thank you.
Thanks Wico! 👍
brilliant Peter... It is 23:11 and I'm off to make some wedges!
Ha! Keep the noise down! 👍 And thanks! 🙌
@@10MinuteWorkshop not really going to do it tonight but I will certainly make a few now as I so often need wedges for doors and just to lift something a tiny bit incrementally etc. etc. It is too dangerous to do this on my mitre saw so, since I have been hankering over a track saw for a while, maybe this is the time to get one... just to make a few wedges and keep my fingers!
Anyway, I am up at 5 so best skedaddle orf to my slumber platz... I recommend the same for you at this unearthly hour btw!😂😂
Hi Peter, awesome video as usual 👍. As a novice, making cuts with the track saw, on thin materials always worries me, as I didn’t really know the best way to achieve it. I was almost considering purchasing a job site track saw, pretty much for just that, as I don’t have a workshop. But you have now given me more confidence in using my track saw (Makita) and rails for doing this, especially as I love using my folding MFT workbench that I built with your plans. The only thing I need to find now, is a shorter piece of track, as my 1400mm long pieces are a bit of a nightmare at times. I think Makita do a 1000mm length, so may go for that.
Also, after watching your videos I purchased the BenchDogs Guide rail set, and will be getting their Square.
Keep up the amazing work, love watching your video with Denis from Hooked on Wood as well. His workshop looks amazing!
Thanks Steve! 👍👍
As always, really well made and very useful video for the track saw users out there. I had wondered if there’s a safe way to make tapered legs using a track saw? It’s something I’ve seen done many times on a table saw, but it would be great if there was a way to do it without having to go down that particular route. And every way I can think of doing it with a track saw seems precarious, at best!
Thanks! Biggest issue with tapered legs - precarious-ness aside - is the depth of cut restricts you to fairly small-section legs! 👍
Pretty smart stuff!
Excellent video. With a track saw and an MFT type system, you can do most things a table saw can.
One that stumps me is how to do an angled cut along the face of a board, as with a door threshold that has a slight ramp. On a table saw, you would put the board against the fence vertically. The blade would have a slight angle away from the fence.
Any idea if this type of cut is possible with a track saw plus your typical MFT type jigs?
Fabulous content ! great delivery and clear VALUE . Know wonder you are living your dream.
Now please tell me what camera and lighting you use . I' m just starting out with a track saw and love it. I hope to use video to explain and demonstrate my design patents to market my ideas to manufactures .Learn from the best!
Thank you so much ! I am going to look at ALL your videos !!!
Thank you! I mostly use Panasonic LUMIX cameras (GH5 and G80) a GoPro 9 and my Phone. Rode microphones have worked well for me. And lighting is just from LED panels in the ceiling - I’m about to replace them, it they’ve lasted pretty well. Hope that helps! Peter. LED panels - ua-cam.com/video/TrukKsGFGO8/v-deo.html
Brilliant! Thank you sir 👍
WOW. Great and helpful tips. Anymore with router and insertring?
I have a ‘router basics’ series planned, yes. 👍👍
My Mrs. is blaming you Peter Routers keep arriving
Plural! I Like your style! 😂 👍
@@10MinuteWorkshop And Dennis from hooked on wood for all these China tools arriving
Really clever stuff - do you have any information on best ways to cut a bevel at greater than 45 degrees, say 60 degrees.
The large Festool HK saw will bevel at 60°, otherwise the only way I know is to chock the rail up with wedges. It’s not something I needed to do a lot, but if I did I’d make a bevel platform of some kind. 👍
I cut sinks,and cooktops out of countertops.
It can get tricky when you have to cut inside your mark while accounting for blade width.
Yep, wish I had the StrawByte waste side jigs back when I was doing them regularly. 👍
Wow, the Strawbyte jigs look cool. I'm in the U.S., so I'm not sure I can buy from their website. They do sell them on Etsy in the U.S., so I just ordered some.
Pretty sure global shipping is available direct, but happy to hear you’re all sorted. 👍👍
any ideas for cutting splines?
What am I missing re. partial bevel cut Peter - surely if using 45 degrees, the distance you overhang the track by is the same distance down from the top surface that you wish the bevel to start, as it makes a right angle isosceles triangle? Merry Christmas! 🎅🏻