i honestly applogize for not commenting earlier but the card in the video is mine, the mans a genius and wizard . he was super cordial and even went out of his to follow up cause i had an issue with my pcie riser not being gen 4. i couldn't recommend him enough.
Do you have core? After 1.8V core voltage comes on. If core voltage is available then you will have to trace from the power good signal of the controller. Do you have a boardview and schematics for any 3080?
@@GraphicsCardRepairs-tk7ql Yes I have boardview but not from Asus specifically, change the IC GS9216 that controls pex, but I think the damage is in that area, because I have the 1.8v but I do not have 1.3 in any of the 4 coils, but in the 18 core phase I have it at 0.8 only in 6 phases, at some point I turn it on and I have all the voltages in the 18 phases 0.8v and the 4 phases 1.3v, I turn it off and turn it back on, the voltages go away Thanks for your response 👍
Nice job, you earned a new sub ! Just starting since my 3090 is crashing a lot randomly and showing errors in MATS but I'm having troubles understanding the report 😅 I have few write errors on multiple bits, yet i have picture and yesterday was able to play normaly for 2 hours at ultra.. Any clue ? I'm close to paying a core reballing but idk 😢
@@GraphicsCardRepairs-tk7ql hmm It boots but sometimes it doesnt and VGA light is on. GPU reballing it is then, need to find someone in France who can do it.. thanks for your help 😃
Could you fix a msi gaming x trio v389 v2.1 Its with 3 power plugs. It sound so much like the issue in this video, but I don't have the schema. Can you help?
Hello boss! Thanks for your informative video! I want to ask you something: What are the chances of a card like this (a MSI suprimX RTX 3080) that has 1.8V and Memory short to ground? (When plugged all the voltages are present except PEX and even the shorted 1.8V rail and Memory Rail have the required voltages). Do you think the Core is alive or dead? (the core heats up normally when I plug it in a computer but the card isn't detected). This card had artifacts at first and someone reflowed it and I think the balls under some ram chips are shorted because it had sparks near the top RGB connector and some ram chips overheated (back then the card was still detected with code 43). Sorry for taking your time boss! ☺☺
In this case you will first have to use the thermal camera and check when applied 1.8V voltage injection which memory is lighting up. Do the same by injecting voltage on memory. Reball or replace the memory that lights up. if only core is lighting up then you will have to remove the core and measure resistance on 1.8V pads on the core. if no short reball and that should fix the issue. If short is still there core is dead. If no reflow was done it was safe to assume that core is dead.
Hi Sir i have RX480 when i power the card sometime phase coils have pulse sometimes not...why?its is a problem or phase controller chip or mosfet driver ic?
So is the GPU not detected? If sometimes the pulse is missing then check the driver IC. Maybe it's failing. How did you check the pulse. Did you use an oscilloscope? Also check the controller. These are tricky ones and difficult to pinpoint without the GPU.
I would suggest you run memory tests for AMD first. Check if there are any memory errors. If you are getting a red display after the driver installs there may be memory errors as well.
I have a question I put the original grey thermal pads on my 6800xt that came with the heat sink on the vrams = the square parts of the pcb, now it boots up but turns into a black screen so I clean it with 99% rubbing alcohol and toothbrush the vrams that has the original grey thermal pads that came with the heatsink that got stuck on the vrams pcb part and remove the original grey thermal pads and now the gpu doesn't boot up no matter how many times I press the power button on the motherboard, so I put the pcb inside uncooked rice to dry out the rubbing alcohol for couple days so my question is, is it short circuit dead or is there a chance to make it work
99% rubbing alcohol is non conductive. So it will not cause any short. Secondly it evaporates instantly. In my video you may have seen I literally pour quite an amount to clean the flux. Sotl that is not the cause of the issue. I have a few questions. Are the fans spinning? If yes check the caps on the PCIE of the GPU. Maybe it is not getting detected.
No the fans are not spinning on the gpu connected to motherboard pcie slot 1 and the same on slot 2 when I press the power button on the motherboard = the lights are on on the motherboard but if I press the power button = no power to post = no signal but if I try with a rx 580 the motherboard turns on with that card connected
Yea that's what I got when I put the original grey thermal pads on the vram on left and right side so I put lots of rubbing alcohol on a tooth brush not pouring the rubbing alcohol on the pcb and clean it by brushing the vrams after that no power so should leave it in bag of uncooked rice or re clean it again with rubbing alcohol
![Gigabyte RTX 3090 Gaming OC graphics card Repair [Not Detected] #nvidia #gpurepair](http://i.ytimg.com/vi/QhyL1EyP4bQ/mqdefault.jpg)
i honestly applogize for not commenting earlier but the card in the video is mine, the mans a genius and wizard . he was super cordial and even went out of his to follow up cause i had an issue with my pcie riser not being gen 4. i couldn't recommend him enough.
@@skyforce911 thank you for your feedback. It means a lot to me. 😁
Amazing as always, learning something new with every video, never stop, will you be making a video for beginners?
Thank you 😁. I will plan a few videos for beginners.
Thanks for the video I have the same problem on an ASUS 3080, but something extra, I have no voltage in memories
Do you have core? After 1.8V core voltage comes on. If core voltage is available then you will have to trace from the power good signal of the controller. Do you have a boardview and schematics for any 3080?
@@GraphicsCardRepairs-tk7ql Yes I have boardview but not from Asus specifically, change the IC GS9216 that controls pex, but I think the damage is in that area, because I have the 1.8v but I do not have 1.3 in any of the 4 coils, but in the 18 core phase I have it at 0.8 only in 6 phases, at some point I turn it on and I have all the voltages in the 18 phases 0.8v and the 4 phases 1.3v, I turn it off and turn it back on, the voltages go away
Thanks for your response 👍
Amazing as always Mr. Frazer💓
Thank you 😁
Music and camera angles I subbed 💪🏾😎👍🏾good 🎉🎉🎉❤
Thank you 😁. Welcome Onboard
Great work bro. 👍🏻
Thank you 😁
Nice job, you earned a new sub !
Just starting since my 3090 is crashing a lot randomly and showing errors in MATS but I'm having troubles understanding the report 😅
I have few write errors on multiple bits, yet i have picture and yesterday was able to play normaly for 2 hours at ultra..
Any clue ? I'm close to paying a core reballing but idk 😢
Thank you and welcome Onboard 😁. On a 3090 if there are memory errors the GPU will not Boot. If your card boots that means you will need a GPU reball.
@@GraphicsCardRepairs-tk7ql hmm It boots but sometimes it doesnt and VGA light is on. GPU reballing it is then, need to find someone in France who can do it.. thanks for your help 😃
really thanks for the video ,
You are welcome! 😁
Clean job!
Thank you 😁.
Could you fix a msi gaming x trio v389 v2.1
Its with 3 power plugs.
It sound so much like the issue in this video, but I don't have the schema.
Can you help?
I fix any Desktop graphics Card from AMD, Nvidia or Intel. You can book your repair by clicking the link in the video description.
Nice job!
Thank you 😁
Hello boss! Thanks for your informative video!
I want to ask you something:
What are the chances of a card like this (a MSI suprimX RTX 3080) that has 1.8V and Memory short to ground?
(When plugged all the voltages are present except PEX and even the shorted 1.8V rail and Memory Rail have the required voltages).
Do you think the Core is alive or dead? (the core heats up normally when I plug it in a computer but the card isn't detected).
This card had artifacts at first and someone reflowed it and I think the balls under some ram chips are shorted because it had sparks near the top RGB connector and some ram chips overheated (back then the card was still detected with code 43).
Sorry for taking your time boss! ☺☺
In this case you will first have to use the thermal camera and check when applied 1.8V voltage injection which memory is lighting up. Do the same by injecting voltage on memory. Reball or replace the memory that lights up. if only core is lighting up then you will have to remove the core and measure resistance on 1.8V pads on the core. if no short reball and that should fix the issue. If short is still there core is dead. If no reflow was done it was safe to assume that core is dead.
@@GraphicsCardRepairs-tk7ql Thanks for your response boss!! I appreciate it! ♥
Why the Vram and ram is not off if PEX is missing Bro?
My gpu is gigabyte 3090
I have follow the video. Register have 5v and 12v
In the 30 series core voltage is not dependent on PEX.
So which voltage is missing
@@GraphicsCardRepairs-tk7qlis not missing sorry 12v and 5v is on, but PEX Voltage is 0v
Hi Sir i have RX480 when i power the card sometime phase coils have pulse sometimes not...why?its is a problem or phase controller chip or mosfet driver ic?
So is the GPU not detected? If sometimes the pulse is missing then check the driver IC. Maybe it's failing. How did you check the pulse. Did you use an oscilloscope? Also check the controller. These are tricky ones and difficult to pinpoint without the GPU.
@@GraphicsCardRepairs-tk7ql GPU Detect But after installing AMD Driver Display goes Red When I run furmark pc direct shutdown..yes i have oscilloscope
And also when i run furmark direct shutdown amd phase dual mosfet short i don't know why..may be faulty controller?
I would suggest you run memory tests for AMD first. Check if there are any memory errors. If you are getting a red display after the driver installs there may be memory errors as well.
@@GraphicsCardRepairs-tk7ql why MOSFET short?
ПОЗЛАТИЛЕ ТИ СЕ ЗЛАТНЕ РУКЕ !
Thank you 😊
I have a question I put the original grey thermal pads on my 6800xt that came with the heat sink on the vrams = the square parts of the pcb, now it boots up but turns into a black screen so I clean it with 99% rubbing alcohol and toothbrush the vrams that has the original grey thermal pads that came with the heatsink that got stuck on the vrams pcb part and remove the original grey thermal pads and now the gpu doesn't boot up no matter how many times I press the power button on the motherboard, so I put the pcb inside uncooked rice to dry out the rubbing alcohol for couple days so my question is, is it short circuit dead or is there a chance to make it work
99% rubbing alcohol is non conductive. So it will not cause any short. Secondly it evaporates instantly. In my video you may have seen I literally pour quite an amount to clean the flux. Sotl that is not the cause of the issue. I have a few questions. Are the fans spinning? If yes check the caps on the PCIE of the GPU. Maybe it is not getting detected.
No the fans are not spinning on the gpu connected to motherboard pcie slot 1 and the same on slot 2 when I press the power button on the motherboard = the lights are on on the motherboard but if I press the power button = no power to post = no signal but if I try with a rx 580 the motherboard turns on with that card connected
Watch this video. ua-cam.com/video/pVFplwoa7jo/v-deo.html
Yea that's what I got when I put the original grey thermal pads on the vram on left and right side so I put lots of rubbing alcohol on a tooth brush not pouring the rubbing alcohol on the pcb and clean it by brushing the vrams after that no power so should leave it in bag of uncooked rice or re clean it again with rubbing alcohol
Is the pc not turning on when GPU is installed or pc turns on but GPU fans not spinning and not detected.