I like your humor/ attitude , im looking at wire harnesses for mine , but i aint tore it down , i didnt know they had that plastic loom on the wires on the inside , thought i was looking at the wrong part ..i keep popping the transmission fuse , and i noticed mines starting to leak from the inside , i heard thats common , everyone ive had does it ..luckily im in florida and i got a heavy duty hoist ..
Hey Man. This is a great video! All other videos regarding the 4L80E are confusing, misinformed and bad video vantage points. Yeah u did a good job with everything. I actually now fully understand what I need to do to my truck. Thanks man. Make some more videos. 😁👍
I have a 91 4wd i don't drive much the connector is leaking im going to epoxy where the wires come thru the harness because i believe it leaks thru shorting to ground and the transmission won't shift out of low,I'll order another new harness harness and see how i come out,thank you for your share!!
It was tough, lube that o-ring with either oil or a light coat of grease, I had to take some pliers and GENTLY twist and pull it thru, it was the last 2mm or so that we’re real tight
Have I seen it yes, is it common, not sure, I’ve seen one bread where it goes into the trans, however that’s usually due to it not being secured, there’s a tab that a bell housing bolt secured to keep it steady and if the trans has been removed before sometime it doesn’t get bolted back down and I’ve seen it break because of that
I'm worried about moisture getting in there and want to fix the problem.... but fluid is very clean and has been changed often... only 242,000 kms.. red as new... mechanic owned
@@andrewbeveridge3006 hmm that’s an odd place to break, unless you have a junkyard near by I’d guess hop on eBay lol you could always try to piece it back together with some jb weld or something but I doubt that would be a permanent fix, I wouldn’t be overly concerned about moisture unless rainwater could get to it, the trans is vented so I mean it’s always exposed to a little atmosphere moisture, you could always get a rubber plug to cap it in the meantime
@@alkarim5890 no there were no bad symptoms other than a trans leak out of the harness connector, I tried resealing it and it didn’t work so I replaced the whole thing
@@hodgepodgegarage3911 thx for the info. My truck transmission wire plug is leaking, I’ve just found that out, I’ve just had B shift solenoid stuck on , no fourth gear ⚙️. I’ve just ordered the B solenoid and a new wire harness, hopefully it’s not a valve body issue !
@@boomyashockya7166 mine doesn’t scream necessarily lol it’s stock and I put an overdrive 700r4 in it, not sure what gears are in the rear, the rear cane from an 81 turbo trans am so it cruises really well but not necessarily a rocket off the line lol working on a vintage air ac kit currently! Will be putting up a video as soon as I ever get the thing back together
I like your humor/ attitude , im looking at wire harnesses for mine , but i aint tore it down , i didnt know they had that plastic loom on the wires on the inside , thought i was looking at the wrong part ..i keep popping the transmission fuse , and i noticed mines starting to leak from the inside , i heard thats common , everyone ive had does it ..luckily im in florida and i got a heavy duty hoist ..
Hey Man. This is a great video! All other videos regarding the 4L80E are confusing, misinformed and bad video vantage points. Yeah u did a good job with everything. I actually now fully understand what I need to do to my truck. Thanks man. Make some more videos. 😁👍
Glad it helped man!
I have a 91 4wd i don't drive much the connector is leaking im going to epoxy where the wires come thru the harness because i believe it leaks thru shorting to ground and the transmission won't shift out of low,I'll order another new harness harness and see how i come out,thank you for your share!!
very helpful! thanks!
Good video! Very helpful 👏🏻
Replacement of the filter sleeve is often not required. Just test fit the new filter. Feel snug? Yep. Then it's good to go.
No dielectric grease? Installed mine and immediately blowing trans fuses.
Nice detail in this video, I'm having trouble pushing the main connector back into the hole. Any advice?
It was tough, lube that o-ring with either oil or a light coat of grease, I had to take some pliers and GENTLY twist and pull it thru, it was the last 2mm or so that we’re real tight
@@hodgepodgegarage3911 thanks for the tip, they really didn't make it easy on us lol
@@KylesCustoms well hopefully they just means it will seal all the better lol
What year truck was this?
94
Hey... quick question.... ever see a broken dip stick tube? Is this another common problem
Have I seen it yes, is it common, not sure, I’ve seen one bread where it goes into the trans, however that’s usually due to it not being secured, there’s a tab that a bell housing bolt secured to keep it steady and if the trans has been removed before sometime it doesn’t get bolted back down and I’ve seen it break because of that
@@hodgepodgegarage3911 mine is bolted... yet broken above the bolt... very hard to find around here and only sold with the transmission
I'm worried about moisture getting in there and want to fix the problem.... but fluid is very clean and has been changed often... only 242,000 kms.. red as new... mechanic owned
@@andrewbeveridge3006 hmm that’s an odd place to break, unless you have a junkyard near by I’d guess hop on eBay lol you could always try to piece it back together with some jb weld or something but I doubt that would be a permanent fix, I wouldn’t be overly concerned about moisture unless rainwater could get to it, the trans is vented so I mean it’s always exposed to a little atmosphere moisture, you could always get a rubber plug to cap it in the meantime
whats with all the sniffles ?
He said it was cold 🥶
What brand that wire harness is ?
It was the cheapest harness I could find on eBay lol not sure of the brand
@@hodgepodgegarage3911 were you getting in transmission error code or any hard transmission shift ?
@@alkarim5890 no there were no bad symptoms other than a trans leak out of the harness connector, I tried resealing it and it didn’t work so I replaced the whole thing
@@hodgepodgegarage3911 thx for the info. My truck transmission wire plug is leaking, I’ve just found that out, I’ve just had B shift solenoid stuck on , no fourth gear ⚙️. I’ve just ordered the B solenoid and a new wire harness, hopefully it’s not a valve body issue !
Does your Bird have a Poncho Engine in it?
Sure does, had a 400, block says it’s from a 75
@@hodgepodgegarage3911 Nice! I've got a 79 with a Pontiac 350 that screams! Mildly modified.
@@boomyashockya7166 mine doesn’t scream necessarily lol it’s stock and I put an overdrive 700r4 in it, not sure what gears are in the rear, the rear cane from an 81 turbo trans am so it cruises really well but not necessarily a rocket off the line lol working on a vintage air ac kit currently! Will be putting up a video as soon as I ever get the thing back together