45 years ago I used to work with a guy who oiled the back of bearing shells. We all gave him a hard time about it, and I guess someone must've taught him to do it that way. None of his engines failed, it was just different to how the rest of us did it.
I am a race shop/Dyno shop owner and engine builder/ race engineer that specializes in building Superbikes WSBK spec $140k+ builds spinning in excess of 15,000+ rpm’s as well as big turbo setup supercar builds to regular evo’s etc and can confirm 100% that Jays method is not problematic whatsoever. Everyone on here fails to hear the words trans fluid being used which by design is extremely thin and actually almost grippy by design, that squishes out about 99% of the 2 micro drops 💧 out of the side of the journals and act as a transport vehicle or secondary insurance that any possible debris will be carried out with it. Which will in fact happen as intended by the very well rounded and world renowned engine builder (Jay) and this is literally intended to help the bearing shells rotate and evenly settle at the parting lines evenly… this is a good method and works flawlessly from PERSONAL EXPERIENCE on some of the highest strung 15,000+ rpm 240whp+ superbike engines that run at full throttle almost 100% of the time for 40+ minutes at a time… so AGAIN this is a tried and true method, if it doesn’t suit you on your build then discard the advice or dont and use it… either way it’s not problematic either way, but without this tip you just need to be 1000% certain surfaces are clear and installed without backing material behind the bearing as well as using a straight edge and pre aligning the shells as evenly as possible. But this method is great as it allows the bearing shell to locate in it’s intended position without the risk of misalignment and binding if not rotated perfectly level. Thx for sharing Jay, and I don’t blame you when you never share another real world engine building tip or secret ingredient to your successful sauce again. Lol you’ve got to remember Jay your just talking to a team of ex F1 engineers and they should be giving you tips 😂🤦🏻♂️. Carry on Jay, building world record breaking 1st’s , and keep innovating and pushing the envelope this is how we grow and achieve that which hasn’t been yet! Take care man!
My problem isn't slippage, you are correct that compression takes care of that. The problem with oiling the back of a plain friction bearing is that you actually add a minute amount of substance to an area where the tolerance should be zero. It probably isn't enough to effect most engines, but it's measurable and it's something to consider. I was taught by an airplane mechanic to always clean the front of the journal on caps and engine until completely free from oils, and to do the same with the back of the bearing. I have never had a problem with seating an un-oiled plain bearing.
Dumb idea and a failed explanation! This definitely takes up space and does tighten the brg clearance Of course, he has to chide anyone who doesn't tow "his line: on "his" post..
Straight to the point, no filler, no annoying anecdotes or personal stories that don’t pertain to the subject matter, and clear terminology. These videos are a breath of fresh air in a world plagued with terrible content. Thank you for these, and please keep them coming.
I'm impressed by seeing it expel the oil on compression. I have changed bearings and learned to put them dry but there's oil back there one way or another after the engine has been used. It's never dry on disassembly.
Was told years ago by machinist. Oil on the back side of bearing will change clearance. Have never oiled backside. Have never had a problem installing bearings. Have also had good luck with engines I have rebuilt. So I am going to stick with no oil on back side. But plenty on the correct side.
Yep the guy that built my motor back in 2000, Dennis at Auto Machine in Orlando Fla (Jay may know the place) told me to NOT oil the back side ... this guy had a huge reputation here in central fla for his building skills.
As a machinist I'm telling you right now that oil on the back side of the bearing will change the clearance. Also if more oil is in one spot than another on the back of the bearing it will cause hot spots on the journal side of the bearing. Think about it, what's the typical clearance of a main or big end bearing? 0.0025 and you are smearing oil on the back side taking away some of that clearance. Oil does not compress, it's hydraulic.
Iv always been told to leave it dry, you can only compress the oil so much and could result in incorrect torque and clearance. Bt each to there own, and if it works for you then fair play
Jay straight communicates his experience. This is a massive gift to us. I’m sold given how hard Jays builds are used and that he gets to forensically pull failures apart. He’s open to others experiences, not preaching.
I work with industrial hydraulic components, and build cylinders. Oil will flow anywhere water will flow, even though the viscosities vary marginally when hot. I’d guess if assembled dry, it wouldn’t take long for oil to get behind all of the bearings, capillary action. There is always space for oil to flow if there is no mechanical seal ( oring etc) Great vid.
@@PhaseConverterampV I've been in this field for over 50 years and I've never seen a bearing that had been run that was dry on the back. Oil it or don't, it's going to get oil in there.
@@realstreetperformance I'm new to your channel & now binge-watching your library of UA-cam Videos. I've developed respect & appreciation for you. I especially appreciate ALL of your valuable tech tips. THANKS!! I have a simple...but sincere...question. QUESTION: What are your thoughts on using engine oil rather than trans. fluid? Do you think engine oil would be too heavy for coating the bearing backs? I would prefer to use engine oil on the back of the crank, rod & cam bearings. Most of my engine builds are Pontiacs; 389, 400 & 455 & a few BB Chevy. Best regards, Ben
I was taught to keep it dry during assembly for measuring and for final assembly. I was taught in a tech school and the theory is right. Your measurements with a dial bore gauge and micrometer will change ever so slightly if you add the thickness of the very thin layer of oil into the measurement, regardless of the oil type being used. That being said, if the experience of an industry expert says it apparently doesn't matter then I believe him. Keep up the solid work🤙 I was the one who asked what your personal future project plans are for Bonneville when you were on the sloppy radio show✌
In the interest of science, try mic'ing one both ways. It will be a month till I'm that deep in an engine again, or i'd do it. I suspect the oil film will evacuate the high spots, making little difference when installed. The key point he drives home is the low viscosity, so seems reasonable.
I agree, but I've seen it documented in many different books that it technically changes your measurements. I've never done a side by side myself but next time I get a chance to I'll find out for science. My dial bore gauge reads extremely accurate and I wonder if it may show me something. My opinion, I highly doubt it would make a difference in bearing clearances in an operating engine if you assembled it wet or dry. And with spinning a bearing, same thing if the machine work is on and the bearings fit correctly or close to correct I definitely dont think it would ever play a role in it spinning. To loose of clearances or not round would definitely effect it, and adding a lubricant film would probably aid in it then.
Never have in 40yrs. of engine building, never will. My work has seen use at over 8000rpm for two plus hours at a time and never has there been any bearing issues. Fact is, I use acetone to clean the back of the bearings and the bearing bores. Oil between the bearing and the rod/cap/main web creates a heat dam (by becoming a carbon layer) which reduces the ability of the bearing to shed heat. The reason main and rod bearing bores are honed to finish size is to create the cross hatch finish that combined with the proper bearing crush all but eliminates the possibility of a spun bearing - the LAST place you want lubrication is the back of the bearing.
Another thing to watch for is if you scrape the backside of the bearing while dropping it in. It's tricky to get the right feel for the squeeze you wanna give the shell to minimize that , and you don't wanna overdo it and bend it. If ya felt ya scraped it a little , see if the sliver/curl is still on the bearing. Remove that with a little blade or scraper or it'll affect the clamp on the bearing. Just a little doodad I learned from an old timer long ago.
@@MrTheHillfolk good comment. I break all the sharp corners on the block, rods, and caps. Nothing real big, I just use a 320 grit stone and round the sharp edge. I'm one of those guys that checks every part that goes in - even open up brand new oil pumps. It's just how I was taught.
I rebuild engines as a profession and I use assembly lube on both sides on every engine I build. Specifically, I put it on the lower bearings, place crankshaft, lube the top of the crank, then put the other side of the bearing on, then spin the crank by hand slowly 2-3 turns. After thousands of builds, its never done me wrong.
I was worried I'd have tear down my motor I'm building. I did the same. Assembly lube on both sides of all my bearings (crank and rod). Not much on the backsides, just a thin coating to help them seat. Glad I'm not the only one who does this.
Genuinely asking, what would be the name of that profession? Small engine mechanic? Machinist/ mechanic (considering honing and decking)? I’m an apprentice rn and I think I’d like to pull and rebuild engines all day further down the road
Same here, was an oilfield mechanic for 24 years and used light oil on the rod end to hold the bearing during inst. i rebuilt anything from Cummins and Detroit Chevy Ford Mopar Pontiac and MG and Sunbeam and Austin-Healey. kinda like all the idiots that have real problem when it comes to ring orientation if you don't think piston rings walk around in the groove while you are driving you're daffy, orient them however you want when you pull them many miles later you'll find out they didn't stay where you put them. There is never just 1. way to do things as soon as you think that, some person will walk up and show you a new and better way to do something you didn't think of. @@ryanalden7793
100% agree I've been rebuilding 4G63 and 4B 11t engines for 10 plus years I always put oil on the backside of the bearings my machinist wants it done this way and has been doing this since the 60s!🇺🇸
35 year journeyman mechanic here. I use a very fine file or 320 emery on the sharp corner of the bearing bore opposite to where the locating tang goes. Just want to knock the sharp edge off so it does not shave metal off the back of the shell. I do this on both mains and rods. Installing the bearings, I get the tang side in place and push the shell into place dry. The bearing crush pushes the shell tightly into place in the bore to hold it firmly in place. Doing a bearing roll during an inframe overhaul, the tang side of the main bearing bore is smoothed carefully and cleaned out thoroughly, as the shell needs to be fed in from the tang side. Done this many times on 400 Fords and Detroit Diesel heavy duty engines. We all have our preferred methods and whatever works for a person, carry on.
End of the day as a engine builder do what works best for you and your customers. There's many ways to do the same thing and get good results. Never hurts to always learn more! Definitely made some good points as I did question this when I first saw it.
,,,I'm new here.....Thank you for the work , time , and professionalism........At 71 my days of acquired knowledge from builders like , Bill Jenkins and Smokey Yunick are very dated...............Minds like yours keep the craft alive............................................
49 years experience, diesel ,gas ,air and liquid cooled . Always installed clean and dry [NEVER used scothbrite] Oil pressure hydraulics bearing and aids in seating the insert to its bore. [Upon disassembly I have witnessed both dry and oily backsides of insert ] This is determined by RMS of surfaces left after machine work and is perfectly acceptable wet or dry . ALWAYS ASSEMBLE WITH BACK OF INSERT CLEAN AND DRY.
I have always done as you do, install dry and clean. Smokey Yunick stated years ago that he cleaned the surfaces with acetone or lacquer thinner, but never explained exactly why. Probably something to do with the bearing conforming closely to the surface of the cap and block during assembly. But I'll continue to install bearing shells dry.
I have been building engines for 40 years. I have worked for some of the biggest and well known engine builders. Keith Black, Mondello, Reath automotive, none of them ever oiled the back of the bearing. The cleaner the back of the bearing the better. Oil will hold the bearing off the jurnal, reducing clearance and reducing heat transfer. Not to mention adding a slick surface for the bearing to spin on.
Exactly!..all these comments how theres nothing with it but it never hurts to get lucky I guess.My uncle works for Keith Dorton,one if the shops that does alot if nascar work and he told me decades ago you never allow oil on the backside of the bearing,common sense really..but common sense is not so common anymore. You want to those bearings to "stick" to the cap or block they are going in.Oil is never meant to be behind them.Period!
I was an diesel engine mechanic, on big engines that I worked on we always put oil on the back side because the oil would help transfer heat away from the bearing. It's just that simple and there is no reason to think that it would not work on small engines.
It’s funny, I grew up around shadetree mechanics and as a kid, I heard about “spun bearings” and engines “blowing up” and now at 35, after hundreds of various engine builds for everything from lawnmowers to skidsteers to Subarus, I’ve never spun a bearing or blown an engine. Old timers were superstitious. My dad thought any engine would “blow up” from sustained revving until he rode in a boat with 2 turbo LS engines that made 700hp each and would run at 4,500 for hours on end.
My bearings are on the way. Came here for advice on putting them in. If Jay says put atf on the rod I will. I've seen a few engine builder's and him I trust the most. Wish me luck 😅
I've essentially been doing this since I was 15 back in 1981. Never have had any bearing issues as long as I use quality bearings and good machining. Clevite CL77 tri metal were my go-to first option though virtually any quality bearing work just fine. BTW great video and we enjoyed it very much.
This makes total sense. I wonder if when going dry, stuff behind the bearing will embed and effect the clearances on the other side of the bearing? I mean oil eventually gets back there. I like his hydraulic flush explanation, very insightful.
I have built hundreds of engines and never oiled the back of the shell bearings on one of them and never had a bearing failure yet either. But when i rebuilt some of the same engines after 16,000 hours on them when i took them apart there was oil behind every shell bearing when i removed them from the block or the con rod. So if you want to oil behind the shell bearings when rebuilding, thats fine. If you dont want to oil behind the shell bearings when rebuilding, thats fine. Whatever works for you stick with it is what i say
Yup, as a Tool and Die Maker myself, there is no way you'll get a smooth and flat enough surface that will seal oil from wicking into the mating area. Absolutely impossible to keep it dry since the honing scratches alone are enough to create tiny gaps.
Jay, your bearing prep tips are absolutely essential. Yes, you could just toss some bearings in and end up with a perfectly healthy engine. For the engine builder to be absolutely certain, that everything was installed perfectly, you would need to take the tips you described. Also, ANYONE who says bearings are to be installed completely dry on the backside and/or that the block's bearing housings are to be cleaned and dried before bearing installation just needs to take one used engine apart. They will clearly see that oil ALWAYS finds it's way, behind the bearing shell. IMHO, I have always lubed the back sides of bearing shells before installation. I have never had a bearing shell that needed cleaning with a scotch bright pad. Always wiped them down with some parts cleaner and a clean lint free rag. Then I'd apply assembly lube on the backside. Just a tiny amount and used a clean finger to spread it out to a thin, even coating. Never once had a bearing failure on a single build. I have built about 100+ engines of all types. Not a large number of builds, but enough to know what is important. Thanks for the tip on using a thin lubricant, like ATF. Instead of using a thin coating of assembly lube.
I worked in Research & Development for Vandervell, the shell bearing manufacturer, building engines for testing on dynamometers and on the road or track. The engines on test beds were subjected to extreme conditions that it would be very difficult or impossible to replicate in use in a vehicle. The test engines were assembled with great care and attention to tolerances and, particularly, cleanliness. They were all assembled with the bearing housings and the backs of the bearings spotlessly clean, degreased, and absolutely DRY, definitely NOT oiled. Care was taken to avoid touching the bearing surfaces, the steel backs of the shells, and the main bearing or rod bearing housings with bare hands to avoid contamination. The bearing surfaces were lubricated once they were installed in the housing immediately before assembly. What they were lubricated with was dictated by the test schedule for that particular engine, but none of it ever went on the backs of the shells. R&D was carried out in two buildings away from the main factory buildings where the shells, thrust washers, and cam bushes, original equipment for many European, Scandinavian, and even some American engines, were manufactured. We had four large soundproof cells in the building where I worked with a total of seven test beds, and another test house in a separate building round the corner with more test beds in cells there. There was also a rig shop where test rigs subjected bearings to excess heat, loading, contamination, lubrication failure, and other abuse. We had a comprehensive machine and welding shop where we produced one-off kit for mounting engines to the beds and dynos, custom plumbing to suit each engine including, on occasion, separate duplicate systems to subject engines to thermal shock and other nasties. (It was handy for producing parts for our own motorcycles and cars during breaks, lunchtimes, and the rare quiet periods too. 😉) All in all, a great job.
I'm going to bet that the bearings were installed "dry" was for two reasons; first, there's a test standard and you have to follow that procedure EXACTLY. Second, I suspect that the test procedure (engine assembly) required dry bearing installation to decrease the potential number of variables that could influence test results. It's easy to quantify and isolate "clean and dry", harder to isolate and consistently say, two drops of oil, ten drops of oil, applied front to back, left to right, big drops, little drops, I lost count of the drops, fresh bottle of oil, old bottle of oil, we didn't use oil, we used antiseize, we used ATF, Dextron vs.... etc. etc. etc. You could spec a procedure that included oil on the back of the bearing, but, like I said, reducing number of variables. I think in this case it had nothing to do with whether it makes a difference or not.
So a trick I use to keep the Parting line of either the Connecting rod or the Main journal from pulling material off the bearing when you put it in is when you are doing your machine work what I do is take a file and put a 45 degree chamfer on the parting line. This keeps your bearing install super clean and no oil needed on the backside.
Yes. This is also what I have been doing for years. Less or no scraping of the back side. I try to use King Bearings for all the engines I do. Now for the novice builder, remember no matter how clean your new parts look they need to be cleaned and inspected.
@@Comet-hn3gm if you happen to do a little scraping , it's not the end of the world just remove the sliver off the bearing before you put the cap on. Yeah oops , but it should be ok just don't keep doing it.
Yep i always soften all the edges easier on bearing install and reduces the chance of having a small burr mess with how the main/rod cap mates to its surface
I was always taught to install them dry. I only watched the video thinking it would be entertaining and instead it was educational. We cant learn without letting ourselves challenge our own beliefs. My next engine I'm applying atf to the cleaned bearings. Thanks for making the video.
Never went crazy with the oil on the backside, but here's the fact! I worked on my own dozens and dozens of different types of engine, to building all out race engines used for drag racing. Then also in my teens to early 20s worked in a engine machine shop, first as an apprenticeship and towards the end being able to machine every part from blocks to cylinder heads and everything in between. We yes I absolutely agree with you on this topic, every running engine I've ever taken apart has a coating of old burned smelling oil on the backsides of rod and main bearings!!! Especially the mains which have oil feed holes through them which need to direct oil to the crankshaft surface. Being you have a couple thou of clearance between the say crank surface and bearing surface well that oil which is sometimes upwards of 80+ PSI coming through the oil galley hole passing through the bearings hole will absolutely seep in between the main saddle and form a film of oil between the block surface and backs of the bearings. Now also this is also the case with the rod bearings, some are sometimes dryer than others but depending upon clearances you can easily get oil behind the backs of the rod bearings. Does this hurt your engine???? Welp from personal experience and plenty of race engines, never once have a bottom end coming back with a crank, rod or bearing issue or having rods letting go, 🤔 I can say does it really make a difference in weather or not to apply a film to the backs of them?? No!!! Yes wipe them down first like everything else that goes into your engines using a solvent first of course. And my personal preference would be to give them a very light coating of oil to help prevent galling of the backs of the bearings against the sharp edges of the block or caps, absolutely 💯% agree. I tried it dry a few times in the beginning and found it was just easier to get the bearings into place than it was dry, especially the camshaft bearings that are pressed into the blocks on pushrod engines. Otherwise you definitely run the risk of galling one on the way in to its position. 😉 I know when it comes to this conversation just like opinions and assholes, everyone has their own. That's great, and I'm sure this technique will be argued about for another 100+ years. The fact of the matter is......... it doesn't really make any difference. But I went with what made things assemble easier and without damaging the backside of the new bearings. I'm sure someone will definitely disagree with me too, but I know my record on never having a bottom end failure attributed to spun bearings or any clearance issues, having more engines under my belt than I could ever remember now, we never had anyone recalled due to something related to this practice, sorry.
I'm so glad to see this posted, for years I've been terrified i was doing it wrong if i put oil on the underside of the bearings, especially in the crank main tunnel. I'm assembling an B18C1 at the moment and i'm going to do it per the instructions here and not worry about doing it that way in the future.
I have been building street/racing motorcycle engines for over 35 years. I always use this method of cleaning, using a light oil and light torque of main and rod caps without the crank to align the bearings and then install everything w Torco or Lubraplate assembly lube. Some of the super stock 600's peak power is over 14k rpm and they see that all day long at the track. Also I have never seen an engine taken apart where it didn't stink like burnt oil when you pulled the bearings, damaged or like brand new. Cars, trucks, tractors, or motorcycles, so oil is always under the bearings.
Hello Jay, thank you for your input on the matter of lubrication "under" the bearing shells. I did not hear you mentioning checking bearing clearance with a plasti-gauge. I never use them right-out-of-the-box unless I check clearance on mains and rods. Having oil under the bearing it will give me a 'false' reading, I do all the plastic-gauging and then remove the bearing and put plenty of the best bearing assembly lube available on the face of all the bearings. Even though I measure all the rods and mains with a dial bore indicator before I install them, I'll make sure all my number are right on. Sorry for the length on this, I don't disagree with your method mine is just slightly different. Thanks again on sharing your knowledge. All the best to you.
I have re-bearinged /rebuilt a lot of engines in 40+ years. Mostly large engines but it's all the same. When I first started working the mechanic doing engines oiled the back of the bearing, and I asked him why. He said it helps the bearing slip into place and align itself. Hmm, I thought about this and wouldn't flood the bearing but would wet the back of the bearing very thinly before snapping it into place.I found it helped. As far as heat transfer, oil is the coolant for the bottom end anyway, it does conduct heat quite well. One thing that makes a huge difference is the mating surfaces of the bearing cap, especially if they have been re-machined they have sharp edges and peel a shaving off the back of the bearing. Bad news later. I recommend a fine file and knock the burrs and sharp edges off, then cleaning of course. Snapping into place is important, if it slips in with no effort, something is wrong.. As far as excessive oil getting hydro-locked, if there is any cross hatch or machining marks in the rod or block bore excess will squeeze out. If there are no marks, that is a problem, indicates wear. Spun bearing on the way, oiled or not. 100% of bearing failures I have seen have nothing to do with using oil on the back of the bearing. I've seen bearings mis-packaged, like one shell std and the other -10. Persons replacing a spun bearing with a new one and hoping for the best. Installing the wrong size bearing. Dirt, grit, poor bearing surfaces. The list goes on.
Am suprised by this... Ive always gone with super clean and dry, always watching for those lil shavings. Cant say Ill ever change that, the physics say its a bad idea, but hey, if you have a successful track record- keep doin what youre doing!!👍👍
Yep... it's much easier to insure NOTHING is stuck to the bearing or bore contact surface if it is DRY... in fact, the oil will tend to attract and CATCH debris.
@@kentuckybowl-o-sticksI agree having oil on back of a bearing will change the clearance in the tens of one thousands and could interfere with heat transfer, that backside film when burnt from heat could create bearing move or walk from loads imo.
@@zdravkomomci7570 Yep... I can't think of any BENEFIT to applying oil there, so... why cloud the issue? Almost like PUTTING weevils in your cereal : )
i was taught 40 years ago that 1) oil takes up space 2) why would you lubricate something that is meant to be a friction fit? 3) the bearing manufacturers have instructions for a reason follow them.
If your theory is true i didn't need to buy +.001 bearings for my new crank i could have just greased the back side of them them. Damn i could have saved $40 on main bearings. If bearing clearance is generally .0025" how much you figure a thin coat of 30 wt. oil will make up. when i disassemble engines the rod end under the bearing has oil in there. wonder how it got there?.
@@markthegunplumber8376it's because the oil freezes once it gets behind the bearing shell and no longer behaves like a FLUID anymore, duh (that was sarcasm, I agree with you)
I don't use any type of oil in the back of the bearings while assembling then. Never used and it never made sense to me. However, I've always spent a lot of time aligning bearing to their beds, specially those without notches. After hearing your opinion, I actually realized that putting a little oil in the back of the bearing will actually make my job of worrying about bearing alignment a lot easier. You've got a very good point.
I agree with this method. Nice to see some one else doing it. I have been looked at sideways when I have done this method. My father was an engine builder in the 60's-80's. This was his tip to me on the first engine I ever built. Great work Jay. Love these info vids. Keep it up crew!!!
My uncle taught me to clean new crankshaft bearings with copper scotchbrite or chorboy. Then lightly coat them with STP, Marvel mystery oil, or mineral oil. He was a great mechanic. 60+ years in the car repair business, lotsa happy customers too. Thanks for sharing🇺🇸 the video post and best 🍀of luck 👍🏼
I've built hundreds of engines over the past 35 years. Have never had an issue without oiling the backside of bearings. Would like to see how much you're temporarily changing oil clearances causing excessive wear on bearings. Will do some measuring on the next assembly just to see. My bet is there is enough for concern
yes larry a very simple check is to assemble with both methods oil on back of bearing and without , assemble both ways with plasti gauge and measure the difference
If the oil couldnt escape and was trapped between the bearing and the housing then yeah it would be of some concern. As its not youre talking maybe 4-6 microns and if your worried about that then you got some serious ocd issues.
@@daveb1870 so you have measured the oil layer after the bearing crush ? And it's .00015748 - .00023622 ? Really ? What'd ya measure it with ? How many engines you built? Excluding the Briggs on your mom's lawn mower. How many are still running ?
40 years doing engines and fit dry on the back when rebuilding but I have done hundreds of top and bottom rolled in mains and also never had a problem. Maybe I will mic some one day but I think either way is fine.
The reaction from people is interesting you either love it or hate it, not like Jay is gonna change how he assembles engines and he has a proven track record so there is clearly merit to the method, I'd certainly give it a try.
I used to build Air cooled, engines for a company in Liverpool, and always put oil on the reverse side of the bearings, even though eddy the boss was not sure, because he used to say I’ve never done that, but I never had any problems with the bottom end of my engine builds, and that was over 20 years ago 👍
I've been oiling the back side of bearings for years.my shop teacher in high school had a brush inside a old plastic carb cleaner cap on his bench and in it was marvel mystery oil thinned slightly with diesel.and would coat both sides.ive been doing it ever since.when you tighten it down it pushes most of it out the sides
@@ezpz7143 I've done probably close to 200 motors and in the last 10 years they have been turbo motors pushing 40 lbs of boost some supercharged motors and a bunch of nitrous supercharged turning 10,000 rpms banging of the rev limiter on jet skis and they seem to last.im gonna keep doing it till I'm proven other wise
@@jeremyking5684 when you put the bearings in like in the video the bearings do slightly move when torquing them down.and as they are almost a perfect fit there is a ever so slight movement.with rotation and heat expansion.exspeacialy in aluminum blocks.and under normal use oil pressure does push oil in between the bearing and the block.
I agree with Jay. Been doing this over 3 decades. I have added oil to the backs of bearing but usually when its a snug fit and the seat action takes a lot of effort or is "sticky" when going in which is most installations.
I’m amazed that any engine can have 10,000 20,000+ hours on them, it’s hard to believe how well they work, when I first learned about piston rings at 6 or 7 I didn’t believe it, “you have metal scraping metal thousands of times a minute, and it’ll last for decades?!?” Motor oil is an amazing thing.
Had a rotating assembly bind up when one of the guys used assembly lube on the back side of the bearings. We pulled it apart cleaned it all off and installed the bearings in dry and the crank rotated. Obviously this is not oil.
Ok, do it the way you want, won't argue. Will say though, the back of the bearing transfers heat to the cap/ block and having clean surface for that heat transfer is important. This is part of the reason for bearing crush. Myself....dry on back, lube on face. My thought is lube plus heat equals poor heat transfer, and also has a very slight effect on clearances. But- do as you like.
Jay is right. Very simple! Folk lore is one thing but proven track records are a different story. They man is beyond meticulous and knows his stuff. Dare anyone to argue that!
I always use red Loctite or red hi-temp silicone sealer. I should not have written that. No doubt someone will do it. Our IH 806G has some interesting stains on the rod and cap where the shells ride. We always used a thin lubricant on the shells. Our junior-high/high school shop student-teacher taught us that in the 1960s. After getting his teaching degree he ran a 289 in a rail at our local drag strip. The dragster was reasonably reliable… and very fast. His ‘Clutch-Flite’ never failed on race day.
Great machinist i knew many years ago always said the back of the bearings is important cuz any foreign material will transfer imperfections through the bearing face
2:00 I kinda see your point there. Putting the oil on the back side allows the bearings to move into proper place as the cap crushes it down. And as you torque it down, we can see the red fluid being pushed out along with the black stuff. Kinda like how window tint is put on with soapy water, they dont put the tint on dry OR when you 1st drop the piston down the cylinder wall, they say to rub wd40 on the cylinder wall so that as the piston is dropped in, the rings dont "scrape" the wall, the wd40 acts as a barrier to allow the piston to smoothly drop in without scrape. So, where as normally we do not put oil there and therefore we are putting a dry bearing surface to another dry metal surface, then as you tighten down the cap, you have 2 dry metal sides being pressed together and if there is a slight mis-alignment, now you potentially have a scratched bearing or crank or rod side. The question i have, IS all the red stuff being pushed out or is there some left under that bearing which CAN cause an issue like everyone is seeing as a thrown bearing .. ?? The video shows the red fluid being pushed out, but is all of it being pushed out ??
I've been building engines since the mid 90's and never lubed the back of the bearing on install. I also never get the sheared off "dirt" when i install them. The block is generally not 100% dry on install either, some amount of rust preventing lube is needed on all blocks. I wipe the back of the bearing and the housing clean with a non-lint cloth and away we go. Purposely oiling between the bearing and housing will change clearances, maybe not enough for a failure, but the change is not predictable or measurable during final assembly and should not be done. When disassembling a properly built engine, you will find little to no lube on the bearing back or the housing. If you are still convinced that you need to do it, use something very thin, like WD40.
I've always dipped the bearing in a container of oil, even use the zinc lube that is important for break-ins. Done lots of HD diesel engines, everything was dipped, caps, bolts unless assembly stated dry.
I put bearings in Cadillac engines for 20yrs at dealership , dry when on the engine stand and when in the car they no doubt got oil on them, never had any issues that came back for bearing problems. If it were my engine they would go in dry than oil, I learned that anything behind a bearing could cause problems. Yes oil gets behind them, the mains through the oil galley hole. I guess I am old school. Jesus Does Save
Like this guy, I have always oiled the backside of a bearing with a thin oil on assembly. I've never spun a bearing although I stuck to stock engines not heavily modified. I doubt it makes a difference, but that's what I did.
We used to rebuild NTC-855 Cummins diesels in the frame. You would do one main at a time and we would clean as best as possible, then roll the top main bearing into place around the crank, install and torque the cap and done. These would run 350-400k miles with no problems. While they didn't turn 8000 rpms, the pressures in a diesel are considerable under load.
I saw in Thailand workshop that in frame they wipe mains with clean rags then spray clean diesel onto the mains cover with rag for an hour before putting on the bearings in. Its hot there and they abuse all things that move but just wondered if this was done by others?
im a car mechanic . i learned rebuilding engines from my father he is a mechanic since 1969 . he taught me to put a slight amount of 10w oil under the bearings . the reason , he said, is what you said EXACTLY!! none of the engines he built failed and none of the engines ive built failed . the thing is that no other mechanics ,i have conversations with ,do that
Nice I always wanted to know why you did that. Now I was also wondering since you tightened the bearings to take measurements then loosen and retighten for final assembly do you loose some of that bearing crush? Thx
I am with Mike below. you cannot get the bearings and rod too clean. I use lacquer thinner to clean everything. the heat transfer is critical from the rod rotating end. I have never lost a rod and have built dozens of high rpm engines. it may work for you but I will never, ever build an engine like that.
This reminds me of a HS physics experiment, where we had sheet pan full of water. We sprinkled talcum powder on the water's surface, then dropped one drop of oil from an eye dropper to the water surface. The oil would spread out over the surface, displacing the talcum, so you could easily see and measure the diameter of the circular patch of oil. Knowing the volume of oil in one drop, and calculating the area of the circular patch of oil, you can divide the volume by the area and calculate the actual minimum thickness of the oil. Personally, I will agree with the cleaning the back side of the bearing shell, but I think I'll still refrain from oiling the backside of bearings.
I have done both and great success both ways. Long as your measurements are spot on and do things properly should be no issues. Just like you said need to get familiar with doing it.
thats key, it works for sure and i wouldnt doubt that considering there are tolerances, and if its out of tolerance or very close within most times itll lightly self clearance and become non issue. but then after a while, that oil will be gone and your clearances would be higher. from my perspective it would be ok to do, but its maybe 25% maybe more, of cases the engine will not last as long. By then something else might have failed. its all chance
It's the crush that holds the bearing in the cap.adding oil on the backside will cause less oil clearance . Too tight will cause the crank to lock up a light oil like you did probably doesn't cause any problem . Good video you hit the points well , I personally don't do this but sounds like you have good luck doing it . I scuff the front of the bearing also the rear .
I've gone through countless engines over the years and the only time I've seen a main or rod bore get remotely hot was when a bearing hammered out and spun. Bearing bores have a honed cross hatch like a cylinder wall so oil makes it's way through the groves anyway.
@@bobroberts2371 the bearing should seat well against the main and rod bore with any clearance to be between the bearing and journal though, there should be no space for oil behind the bearings. They crush at the seams (as the video explains) and I really don’t think the goal of honing a main or rod bore is a similar RA as a cylinder, it’s only used to make it proper size. 🤷♂️ I’m no expert but the people I work for claim to be
@@kylekeck9617 The bearing bore and back of the bearing are not polished smooth so oil will eventually wick behind the bearing when the engine is in operation. I'm well aware that the primary goal of line honing is to side the bearing bore. My point is the honing leaves peaks and valleys, this allows oil to migrate between the bearing and bore. I don't intentionally put oil on the back of the bearing however, thin oil does not pose any problems.
Why not put oil and wipe it off just making it a slippery surface, so it wont effect the clearance as mentioned by experts in the comments. Thank you for sharing your knowledge 👍
Kawasaki recommends lubing the back of the bearings on various models....the old ZX-11 is one I distinctly remember. They actually recommended moly lube. I have always off set the bearings in the cap/saddles so as they self align when crushed .
What happens when you take a motor apart and remove the rod bearing? There is oil on the back side right? So what's the harm in adding oil on the back during assembly?
Change clearances in the beginning,those galleys aren't used untill full assembly then primed. I've never put oil in the back of a bearing due to measuring for clearances but I agree that we should see a video with clearances with and without oil on the back. If it dramatically closes off the clearancing that could be an issue to begin with
I did an apprenticeship in a reconditioning shop and then a further 20 years and i cant say that the engines i have ever pulled apart had oil under the rod bearings they were pretty much always dry. I learnt all about tunnel sizes nip, crush etc but not to put oil under the shell nor have i ever seen anyone else do it.
@@ahmedsimmons4465 Common sense tells you that any oil foolishly put under the bearing shell will get squeezed out when the caps are tensioned as the bearings are designed to be an interference fit when the caps are tightened this is where the nip and crush come into play.
I like to do final assembly with the bearing backsides dry. But I agree it all comes down to crush. Similar to a press fit component, oil there won't matter. I've even seen people use tin foil or newspaper on a back side to tighten up a clearance. If you spun a bearing because of a bit of oil on the back of a bearing you had a major issue somewhere. Important to remember that mains on some engines have oil pressure at all times behind ~1/3 of the bearing width too.
I never oil the back of the bearings, but back in the day I did a lot of in-chassis rebuilds, and a lot of bearing roll ins. Damn things will drip oil for like a week so it's kind of unavoidable to get some oil on the back. I never worried about it and it never hurt anything. I used to have most in-chassis done in a day, and a bearing roll-in done before lunch, so there was no time to let them drip until it stopped. Truck and equipment downtime is way too expensive to worry about crap like that. At the time we were billing the trucks out at 100 per hour, and that was 30 years ago. No time to pretend you're working for NASA
Never oiled the back of a bearing before always just clean them really well but I’m open to trying it on my own personal engines. If it works for Jay on the high power builds he does I’m pretty sure it’s okay to use a really light oil on the saddles anyways Would love to see more on that B20 build I’m sure it’s been done and running but hey can’t hurt to ask right ?! 🤷🏼♂️
That was more interesting than I thought it would be. Using a small amount of ATF (a much thinner fluid) on the backside is not the same as putting assembly lube on the front side. Still, I've never put any oil of any sort on the backside of bearings and I don't think I'm going to start now.
Thank you for your videos, I disagree with lubricating the back of the bearing shell for assembly. I think it would be good next video showing what rod bearing nip is, how it is measured and the engineering purpose behind it ie to provide interference fit between the bearing shell and bearing journal housing. Adding oil only increases the likely hood of bearing shell movement at break in. The problem is other less experienced people see this as a must do and bests practice when it is not. Please do not take this as a negative I like your videos and enjoy learning from them.
Dave I appreciate your input. And respect your right to disagree. This is how we have found success without failure. However, We had the same concern with people possibly thinking our open discussion could be misinterpreted as us saying it is a must do or best practice. Which is why we shot this video more than once and took precaution to use language that specifically did not imply this is a must do and did not present it as a best practice. This is a video about how we do it and why. We have had great success building engines that break records and live longer than the standard expectation for other engines at that power per cubic inch level and people often ask for a peek behind the curtain on how we do it. So these videos show how it gets done. You are not the first person to feel a resistance or hesitation about this method. We have had old timers that never graduated high school quoting their fathers’ fathers all the way to engineers pulling out text books to quote formulas they were taught in school. But it all boils down to many people grew up being told “you can’t apply oil to the back of the bearing or it will move and you will spin it” by someone else and (because it is easy to believe without questioning) they locked that belief system in as gospel and carried it through life. It’s one thing for people to disagree on a theory that none of them have personally tested in practice in the field. That actually happens all the time and can be healthy in encouraging testing and experimentation to find the truth. But it is a weird feeling to describe when people that have never actually tested the theory and produced a negative result from it argue that it won’t work to someone that spent their whole life putting it into practice with nothing but positive results and not a single negative result yet. If you’ve been a fan of this channel for some time you may have noticed that we try to present information that is normally hoarded away as proprietary in a way that could be understood by almost anyone regardless of their experience level. There are some technical topics that we either over simplify or skip all together if the explanation has to get too technical. Our team is composed of a diverse group ranging from people that got their GED without finishing high school all the way to engineers that decide what project car to buy next with custom spreadsheets and made up performance metric formula index matrixes. But regardless of their come-up they are some of the best in the industry today. There are many internal conversations where someone says “but I was always told….” or “but this engineering text book says…” or “but it’s just physics, it should…” while the other side of the table is saying “I hear you, but here are the actual results of the actual testing” it’s a good counter balance. We believe that the theories taught to us by our parents and teachers and schools help pick a direction in narrowing down the path for our own investigation and experimentation. But the results are the results. One of the questions we ask each other a lot around the shop is “how do you know what you know?” If the answer is “someone told me so” or “I read it in a book” then it should be classified differently in your head than the things you actually know. Maybe it happens to be true, or maybe the person you heard it from was mistaken. Or maybe their statement was only true under a certain condition that they left out at that time. Or maybe they were just repeating something that THEY were told and never tested and it’s just passing down through the spoken word over time like a fable. Either way we enjoy these types of topics because they generate healthy arguments that create results from speculation that everyone can learn from. So we appreciate you joining the conversation and hope you will continue to do so in future videos. I appreciate that you disagreed respectfully and constructively and You do help the channel be interacting.
First time I've ever heard anyone go into this subject , always wondered about , looks like next time I will be adding bearing cleaning and back side light lubricating to the engine builds. 👍
45 years ago I used to work with a guy who oiled the back of bearing shells. We all gave him a hard time about it, and I guess someone must've taught him to do it that way. None of his engines failed, it was just different to how the rest of us did it.
It's going to make its way there behind it regardless. lol.
@@8145dwerdna ,,damn true.............capillary effect or action in the hot engine draws oil everywhere............
Did he use regular engine oil? Im about to attempt this on my car.
Agree
@@broke_dongleatf still tightens oil clearances, on the wrong side of the bearing.
I am a race shop/Dyno shop owner and engine builder/ race engineer that specializes in building Superbikes WSBK spec $140k+ builds spinning in excess of 15,000+ rpm’s as well as big turbo setup supercar builds to regular evo’s etc and can confirm 100% that Jays method is not problematic whatsoever. Everyone on here fails to hear the words trans fluid being used which by design is extremely thin and actually almost grippy by design, that squishes out about 99% of the 2 micro drops 💧 out of the side of the journals and act as a transport vehicle or secondary insurance that any possible debris will be carried out with it. Which will in fact happen as intended by the very well rounded and world renowned engine builder (Jay) and this is literally intended to help the bearing shells rotate and evenly settle at the parting lines evenly… this is a good method and works flawlessly from PERSONAL EXPERIENCE on some of the highest strung 15,000+ rpm 240whp+ superbike engines that run at full throttle almost 100% of the time for 40+ minutes at a time… so AGAIN this is a tried and true method, if it doesn’t suit you on your build then discard the advice or dont and use it… either way it’s not problematic either way, but without this tip you just need to be 1000% certain surfaces are clear and installed without backing material behind the bearing as well as using a straight edge and pre aligning the shells as evenly as possible. But this method is great as it allows the bearing shell to locate in it’s intended position without the risk of misalignment and binding if not rotated perfectly level.
Thx for sharing Jay, and I don’t blame you when you never share another real world engine building tip or secret ingredient to your successful sauce again. Lol you’ve got to remember Jay your just talking to a team of ex F1 engineers and they should be giving you tips 😂🤦🏻♂️. Carry on Jay, building world record breaking 1st’s , and keep innovating and pushing the envelope this is how we grow and achieve that which hasn’t been yet! Take care man!
Sooo Dexron VI or Type F?
💯
Positive
My problem isn't slippage, you are correct that compression takes care of that. The problem with oiling the back of a plain friction bearing is that you actually add a minute amount of substance to an area where the tolerance should be zero. It probably isn't enough to effect most engines, but it's measurable and it's something to consider. I was taught by an airplane mechanic to always clean the front of the journal on caps and engine until completely free from oils, and to do the same with the back of the bearing. I have never had a problem with seating an un-oiled plain bearing.
That was my first thought when I saw this.
❤😮😅9pm I f9 7th😊😅😢8 5:13 9
Dumb idea and a failed explanation!
This definitely takes up space and does tighten the brg clearance
Of course, he has to chide anyone who doesn't tow "his line: on "his" post..
@@billjenkins3699 Is that you Grumpy, the legendary drag racer.
@donziperk nah, real the grump passed
Straight to the point, no filler, no annoying anecdotes or personal stories that don’t pertain to the subject matter, and clear terminology.
These videos are a breath of fresh air in a world plagued with terrible content. Thank you for these, and please keep them coming.
Tell me have you ever stripped an engine and found the back of a bearing bone dry,🤷♂️
I'm impressed by seeing it expel the oil on compression. I have changed bearings and learned to put them dry but there's oil back there one way or another after the engine has been used. It's never dry on disassembly.
I think it gets the from the oil gallery holes.
@@donziperkthermal cycling and wicking due to capillary action
@@wlrottge More technically explained but yes.
Was told years ago by machinist. Oil on the back side of bearing will change clearance. Have never oiled backside. Have never had a problem installing bearings. Have also had good luck with engines I have rebuilt. So I am going to stick with no oil on back side. But plenty on the correct side.
Thanks for sharing
Yep the guy that built my motor back in 2000, Dennis at Auto Machine in Orlando Fla (Jay may know the place) told me to NOT oil the back side ... this guy had a huge reputation here in central fla for his building skills.
As a machinist I'm telling you right now that oil on the back side of the bearing will change the clearance. Also if more oil is in one spot than another on the back of the bearing it will cause hot spots on the journal side of the bearing.
Think about it, what's the typical clearance of a main or big end bearing? 0.0025 and you are smearing oil on the back side taking away some of that clearance. Oil does not compress, it's hydraulic.
Iv always been told to leave it dry, you can only compress the oil so much and could result in incorrect torque and clearance. Bt each to there own, and if it works for you then fair play
@@mervynsweeney2948 well if they are building 2000 hp 2JZ's and none are throwing any bearings, then i guess his method works.
Jay straight communicates his experience. This is a massive gift to us. I’m sold given how hard Jays builds are used and that he gets to forensically pull failures apart. He’s open to others experiences, not preaching.
exactly not sure why people wanna argue with the dude LOL
Thank you!
I work with industrial hydraulic components, and build cylinders. Oil will flow anywhere water will flow, even though the viscosities vary marginally when hot. I’d guess if assembled dry, it wouldn’t take long for oil to get behind all of the bearings, capillary action. There is always space for oil to flow if there is no mechanical seal ( oring etc) Great vid.
@@PhaseConverterampV I've been in this field for over 50 years and I've never seen a bearing that had been run that was dry on the back. Oil it or don't, it's going to get oil in there.
@@realstreetperformance I'm new to your channel & now binge-watching
your library of UA-cam Videos. I've developed respect & appreciation for you.
I especially appreciate ALL of your valuable tech tips. THANKS!!
I have a simple...but sincere...question.
QUESTION: What are your thoughts on using engine oil rather than trans. fluid?
Do you think engine oil would be too heavy for coating the bearing backs?
I would prefer to use engine oil on the back of the crank, rod & cam bearings.
Most of my engine builds are Pontiacs; 389, 400 & 455 & a few BB Chevy.
Best regards,
Ben
I was taught to keep it dry during assembly for measuring and for final assembly. I was taught in a tech school and the theory is right. Your measurements with a dial bore gauge and micrometer will change ever so slightly if you add the thickness of the very thin layer of oil into the measurement, regardless of the oil type being used. That being said, if the experience of an industry expert says it apparently doesn't matter then I believe him. Keep up the solid work🤙 I was the one who asked what your personal future project plans are for Bonneville when you were on the sloppy radio show✌
In the interest of science, try mic'ing one both ways. It will be a month till I'm that deep in an engine again, or i'd do it. I suspect the oil film will evacuate the high spots, making little difference when installed. The key point he drives home is the low viscosity, so seems reasonable.
I very seriously doubt you'd any measurable difference.
see
I agree, but I've seen it documented in many different books that it technically changes your measurements. I've never done a side by side myself but next time I get a chance to I'll find out for science. My dial bore gauge reads extremely accurate and I wonder if it may show me something. My opinion, I highly doubt it would make a difference in bearing clearances in an operating engine if you assembled it wet or dry. And with spinning a bearing, same thing if the machine work is on and the bearings fit correctly or close to correct I definitely dont think it would ever play a role in it spinning. To loose of clearances or not round would definitely effect it, and adding a lubricant film would probably aid in it then.
@@jeffreydurham5342I would agree with you but then we would both be wrong, it is measurable.
Never have in 40yrs. of engine building, never will. My work has seen use at over 8000rpm for two plus hours at a time and never has there been any bearing issues.
Fact is, I use acetone to clean the back of the bearings and the bearing bores.
Oil between the bearing and the rod/cap/main web creates a heat dam (by becoming a carbon layer) which reduces the ability of the bearing to shed heat.
The reason main and rod bearing bores are honed to finish size is to create the cross hatch finish that combined with the proper bearing crush all but eliminates the possibility of a spun bearing - the LAST place you want lubrication is the back of the bearing.
Thanks for the feedback Mike!
Another thing to watch for is if you scrape the backside of the bearing while dropping it in.
It's tricky to get the right feel for the squeeze you wanna give the shell to minimize that , and you don't wanna overdo it and bend it.
If ya felt ya scraped it a little , see if the sliver/curl is still on the bearing.
Remove that with a little blade or scraper or it'll affect the clamp on the bearing.
Just a little doodad I learned from an old timer long ago.
i am 67 started at 17 l1 master car and truck so i have done a few engines in my time and you took the words out of my mouth
@@MrTheHillfolk good comment.
I break all the sharp corners on the block, rods, and caps.
Nothing real big, I just use a 320 grit stone and round the sharp edge.
I'm one of those guys that checks every part that goes in - even open up brand new oil pumps.
It's just how I was taught.
@@realstreetperformance
Absolutely.
We all have methods we're successful with, as long as the end result is the same we're good.
I rebuild engines as a profession and I use assembly lube on both sides on every engine I build. Specifically, I put it on the lower bearings, place crankshaft, lube the top of the crank, then put the other side of the bearing on, then spin the crank by hand slowly 2-3 turns. After thousands of builds, its never done me wrong.
I was worried I'd have tear down my motor I'm building. I did the same. Assembly lube on both sides of all my bearings (crank and rod). Not much on the backsides, just a thin coating to help them seat. Glad I'm not the only one who does this.
Genuinely asking, what would be the name of that profession? Small engine mechanic? Machinist/ mechanic (considering honing and decking)? I’m an apprentice rn and I think I’d like to pull and rebuild engines all day further down the road
Same here, was an oilfield mechanic for 24 years and used light oil on the rod end to hold the bearing during inst. i rebuilt anything from Cummins and Detroit Chevy Ford Mopar Pontiac and MG and Sunbeam and Austin-Healey. kinda like all the idiots that have real problem when it comes to ring orientation if you don't think piston rings walk around in the groove while you are driving you're daffy, orient them however you want when you pull them many miles later you'll find out they didn't stay where you put them. There is never just 1. way to do things as soon as you think that, some person will walk up and show you a new and better way to do something you didn't think of. @@ryanalden7793
100% agree I've been rebuilding 4G63 and 4B 11t engines for 10 plus years I always put oil on the backside of the bearings my machinist wants it done this way and has been doing this since the 60s!🇺🇸
Just regular engine oil? (Im about to do this on my car in my driveway)
Occupational school in sixties in Finland we were taught to oil back of the bearing shells, done that ever since. Thanks to the good video.
35 year journeyman mechanic here. I use a very fine file or 320 emery on the sharp corner of the bearing bore opposite to where the locating tang goes. Just want to knock the sharp edge off so it does not shave metal off the back of the shell. I do this on both mains and rods. Installing the bearings, I get the tang side in place and push the shell into place dry. The bearing crush pushes the shell tightly into place in the bore to hold it firmly in place.
Doing a bearing roll during an inframe overhaul, the tang side of the main bearing bore is smoothed carefully and cleaned out thoroughly, as the shell needs to be fed in from the tang side. Done this many times on 400 Fords and Detroit Diesel heavy duty engines.
We all have our preferred methods and whatever works for a person, carry on.
End of the day as a engine builder do what works best for you and your customers. There's many ways to do the same thing and get good results. Never hurts to always learn more! Definitely made some good points as I did question this when I first saw it.
,,,I'm new here.....Thank you for the work , time , and professionalism........At 71 my days of acquired knowledge from builders like , Bill Jenkins and Smokey Yunick are very dated...............Minds like yours keep the craft alive............................................
Great info. Thanks so much for explaining all this will definitely put it to use on our next engine build.
49 years experience, diesel ,gas ,air and liquid cooled . Always installed clean and dry [NEVER used scothbrite] Oil pressure hydraulics bearing and aids in seating the insert to its bore. [Upon disassembly I have witnessed both dry and oily backsides of insert ] This is determined by RMS of surfaces left after machine work and is perfectly acceptable wet or dry . ALWAYS ASSEMBLE WITH BACK OF INSERT CLEAN AND DRY.
I think I'm gonna go with Jay, he's more up to date with the information.
No
@@seankimbrough8489jay also doesn't know the difference between over and undersized bearings if you go watch that video.
I have always done as you do, install dry and clean. Smokey Yunick stated years ago that he cleaned the surfaces with acetone or lacquer thinner, but never explained exactly why. Probably something to do with the bearing conforming closely to the surface of the cap and block during assembly. But I'll continue to install bearing shells dry.
@@briggsquantum , Smokey was one hell of a mechanic.
I have been building engines for 40 years. I have worked for some of the biggest and well known engine builders. Keith Black, Mondello, Reath automotive, none of them ever oiled the back of the bearing.
The cleaner the back of the bearing the better. Oil will hold the bearing off the jurnal, reducing clearance and reducing heat transfer. Not to mention adding a slick surface for the bearing to spin on.
Exactly!..all these comments how theres nothing with it but it never hurts to get lucky I guess.My uncle works for Keith Dorton,one if the shops that does alot if nascar work and he told me decades ago you never allow oil on the backside of the bearing,common sense really..but common sense is not so common anymore. You want to those bearings to "stick" to the cap or block they are going in.Oil is never meant to be behind them.Period!
you need to learn how to spell first... what is jurnal ??? is that a new word for you high tech engine intellectuals ???
@@johncasor9698 Mmmmmm,an ad hominem attack…says a lot about your intellect…
I was an diesel engine mechanic, on big engines that I worked on we always put oil on the back side because the oil would help transfer heat away from the bearing. It's just that simple and there is no reason to think that it would not work on small engines.
It’s funny, I grew up around shadetree mechanics and as a kid, I heard about “spun bearings” and engines “blowing up” and now at 35, after hundreds of various engine builds for everything from lawnmowers to skidsteers to Subarus, I’ve never spun a bearing or blown an engine. Old timers were superstitious. My dad thought any engine would “blow up” from sustained revving until he rode in a boat with 2 turbo LS engines that made 700hp each and would run at 4,500 for hours on end.
My bearings are on the way. Came here for advice on putting them in. If Jay says put atf on the rod I will. I've seen a few engine builder's and him I trust the most.
Wish me luck 😅
I've essentially been doing this since I was 15 back in 1981. Never have had any bearing issues as long as I use quality bearings and good machining. Clevite CL77 tri metal were my go-to first option though virtually any quality bearing work just fine. BTW great video and we enjoyed it very much.
"i have a, pretty good track record on success, as far as putting engines together and not having them fail due to assembly error"
always humble
matt you made me giggle lol
And make over 900 whp on stock components including re using head gaskets and torque to yield bolts.
A true legend of the masses. We love you sloppy.
Hey mat remember the 240 lol
This makes total sense. I wonder if when going dry, stuff behind the bearing will embed and effect the clearances on the other side of the bearing? I mean oil eventually gets back there. I like his hydraulic flush explanation, very insightful.
I have built hundreds of engines and never oiled the back of the shell bearings on one of them and never had a bearing failure yet either. But when i rebuilt some of the same engines after 16,000 hours on them when i took them apart there was oil behind every shell bearing when i removed them from the block or the con rod. So if you want to oil behind the shell bearings when rebuilding, thats fine. If you dont want to oil behind the shell bearings when rebuilding, thats fine. Whatever works for you stick with it is what i say
Yup, as a Tool and Die Maker myself, there is no way you'll get a smooth and flat enough surface that will seal oil from wicking into the mating area. Absolutely impossible to keep it dry since the honing scratches alone are enough to create tiny gaps.
Jay, your bearing prep tips are absolutely essential. Yes, you could just toss some bearings in and end up with a perfectly healthy engine. For the engine builder to be absolutely certain, that everything was installed perfectly, you would need to take the tips you described. Also, ANYONE who says bearings are to be installed completely dry on the backside and/or that the block's bearing housings are to be cleaned and dried before bearing installation just needs to take one used engine apart. They will clearly see that oil ALWAYS finds it's way, behind the bearing shell. IMHO, I have always lubed the back sides of bearing shells before installation. I have never had a bearing shell that needed cleaning with a scotch bright pad. Always wiped them down with some parts cleaner and a clean lint free rag. Then I'd apply assembly lube on the backside. Just a tiny amount and used a clean finger to spread it out to a thin, even coating. Never once had a bearing failure on a single build. I have built about 100+ engines of all types. Not a large number of builds, but enough to know what is important. Thanks for the tip on using a thin lubricant, like ATF. Instead of using a thin coating of assembly lube.
I worked in Research & Development for Vandervell, the shell bearing manufacturer, building engines for testing on dynamometers and on the road or track. The engines on test beds were subjected to extreme conditions that it would be very difficult or impossible to replicate in use in a vehicle.
The test engines were assembled with great care and attention to tolerances and, particularly, cleanliness. They were all assembled with the bearing housings and the backs of the bearings spotlessly clean, degreased, and absolutely DRY, definitely NOT oiled. Care was taken to avoid touching the bearing surfaces, the steel backs of the shells, and the main bearing or rod bearing housings with bare hands to avoid contamination. The bearing surfaces were lubricated once they were installed in the housing immediately before assembly. What they were lubricated with was dictated by the test schedule for that particular engine, but none of it ever went on the backs of the shells.
R&D was carried out in two buildings away from the main factory buildings where the shells, thrust washers, and cam bushes, original equipment for many European, Scandinavian, and even some American engines, were manufactured.
We had four large soundproof cells in the building where I worked with a total of seven test beds, and another test house in a separate building round the corner with more test beds in cells there.
There was also a rig shop where test rigs subjected bearings to excess heat, loading, contamination, lubrication failure, and other abuse.
We had a comprehensive machine and welding shop where we produced one-off kit for mounting engines to the beds and dynos, custom plumbing to suit each engine including, on occasion, separate duplicate systems to subject engines to thermal shock and other nasties. (It was handy for producing parts for our own motorcycles and cars during breaks, lunchtimes, and the rare quiet periods too. 😉)
All in all, a great job.
I'm going to bet that the bearings were installed "dry" was for two reasons; first, there's a test standard and you have to follow that procedure EXACTLY.
Second, I suspect that the test procedure (engine assembly) required dry bearing installation to decrease the potential number of variables that could influence test results. It's easy to quantify and isolate "clean and dry", harder to isolate and consistently say, two drops of oil, ten drops of oil, applied front to back, left to right, big drops, little drops, I lost count of the drops, fresh bottle of oil, old bottle of oil, we didn't use oil, we used antiseize, we used ATF, Dextron vs.... etc. etc. etc.
You could spec a procedure that included oil on the back of the bearing, but, like I said, reducing number of variables. I think in this case it had nothing to do with whether it makes a difference or not.
@@wlrottge very plausible, might be the answer to the topic.
So a trick I use to keep the Parting line of either the Connecting rod or the Main journal from pulling material off the bearing when you put it in is when you are doing your machine work what I do is take a file and put a 45 degree chamfer on the parting line. This keeps your bearing install super clean and no oil needed on the backside.
Yes. This is also what I have been doing for years. Less or no scraping of the back side. I try to use King Bearings for all the engines I do. Now for the novice builder, remember no matter how clean your new parts look they need to be cleaned and inspected.
Yes, I do as well.
Oil doesn't belong on the backside of the bearings.
@@Comet-hn3gm if you happen to do a little scraping , it's not the end of the world just remove the sliver off the bearing before you put the cap on.
Yeah oops , but it should be ok just don't keep doing it.
Yep i always soften all the edges easier on bearing install and reduces the chance of having a small burr mess with how the main/rod cap mates to its surface
Correct.
I was always taught to install them dry. I only watched the video thinking it would be entertaining and instead it was educational. We cant learn without letting ourselves challenge our own beliefs. My next engine I'm applying atf to the cleaned bearings. Thanks for making the video.
Never went crazy with the oil on the backside, but here's the fact! I worked on my own dozens and dozens of different types of engine, to building all out race engines used for drag racing. Then also in my teens to early 20s worked in a engine machine shop, first as an apprenticeship and towards the end being able to machine every part from blocks to cylinder heads and everything in between. We yes I absolutely agree with you on this topic, every running engine I've ever taken apart has a coating of old burned smelling oil on the backsides of rod and main bearings!!! Especially the mains which have oil feed holes through them which need to direct oil to the crankshaft surface. Being you have a couple thou of clearance between the say crank surface and bearing surface well that oil which is sometimes upwards of 80+ PSI coming through the oil galley hole passing through the bearings hole will absolutely seep in between the main saddle and form a film of oil between the block surface and backs of the bearings. Now also this is also the case with the rod bearings, some are sometimes dryer than others but depending upon clearances you can easily get oil behind the backs of the rod bearings. Does this hurt your engine???? Welp from personal experience and plenty of race engines, never once have a bottom end coming back with a crank, rod or bearing issue or having rods letting go, 🤔 I can say does it really make a difference in weather or not to apply a film to the backs of them?? No!!! Yes wipe them down first like everything else that goes into your engines using a solvent first of course. And my personal preference would be to give them a very light coating of oil to help prevent galling of the backs of the bearings against the sharp edges of the block or caps, absolutely 💯% agree. I tried it dry a few times in the beginning and found it was just easier to get the bearings into place than it was dry, especially the camshaft bearings that are pressed into the blocks on pushrod engines. Otherwise you definitely run the risk of galling one on the way in to its position. 😉 I know when it comes to this conversation just like opinions and assholes, everyone has their own. That's great, and I'm sure this technique will be argued about for another 100+ years. The fact of the matter is......... it doesn't really make any difference. But I went with what made things assemble easier and without damaging the backside of the new bearings. I'm sure someone will definitely disagree with me too, but I know my record on never having a bottom end failure attributed to spun bearings or any clearance issues, having more engines under my belt than I could ever remember now, we never had anyone recalled due to something related to this practice, sorry.
so what is your point???
@@johncasor9698- Thank you! Someone had to ask.
I'm so glad to see this posted, for years I've been terrified i was doing it wrong if i put oil on the underside of the bearings, especially in the crank main tunnel. I'm assembling an B18C1 at the moment and i'm going to do it per the instructions here and not worry about doing it that way in the future.
I have been building street/racing motorcycle engines for over 35 years. I always use this method of cleaning, using a light oil and light torque of main and rod caps without the crank to align the bearings and then install everything w Torco or Lubraplate assembly lube. Some of the super stock 600's peak power is over 14k rpm and they see that all day long at the track. Also I have never seen an engine taken apart where it didn't stink like burnt oil when you pulled the bearings, damaged or like brand new. Cars, trucks, tractors, or motorcycles, so oil is always under the bearings.
Great information. I will use this trick tomorrow when installing my main and rod bearings. Knowledge is Power.
Hello Jay, thank you for your input on the matter of lubrication "under" the bearing shells. I did not hear you mentioning checking bearing clearance with a plasti-gauge. I never use them right-out-of-the-box unless I check clearance on mains and rods. Having oil under the bearing it will give me a 'false' reading, I do all the plastic-gauging and then remove the bearing and put plenty of the best bearing assembly lube available on the face of all the bearings. Even though I measure all the rods and mains with a dial bore indicator before I install them, I'll make sure all my number are right on. Sorry for the length on this, I don't disagree with your method mine is just slightly different. Thanks again on sharing your knowledge. All the best to you.
I have re-bearinged /rebuilt a lot of engines in 40+ years.
Mostly large engines but it's all the same.
When I first started working the mechanic doing engines oiled the back of the bearing, and I asked him why. He said it helps the bearing slip into place and align itself.
Hmm, I thought about this and wouldn't flood the bearing but would wet the back of the bearing very thinly before snapping it into place.I found it helped.
As far as heat transfer, oil is the coolant for the bottom end anyway, it does conduct heat quite well.
One thing that makes a huge difference is the mating surfaces of the bearing cap, especially if they have been re-machined they have sharp edges and peel a shaving off the back of the bearing. Bad news later. I recommend a fine file and knock the burrs and sharp edges off, then cleaning of course.
Snapping into place is important, if it slips in with no effort, something is wrong..
As far as excessive oil getting hydro-locked, if there is any cross hatch or machining marks in the rod or block bore excess will squeeze out. If there are no marks, that is a problem, indicates wear. Spun bearing on the way, oiled or not.
100% of bearing failures I have seen have nothing to do with using oil on the back of the bearing.
I've seen bearings mis-packaged, like one shell std and the other -10. Persons replacing a spun bearing with a new one and hoping for the best. Installing the wrong size bearing. Dirt, grit, poor bearing surfaces. The list goes on.
Am suprised by this... Ive always gone with super clean and dry, always watching for those lil shavings. Cant say Ill ever change that, the physics say its a bad idea, but hey, if you have a successful track record- keep doin what youre doing!!👍👍
Yep... it's much easier to insure NOTHING is stuck to the bearing or bore contact surface if it is DRY... in fact, the oil will tend to attract and CATCH debris.
@@kentuckybowl-o-sticksI agree having oil on back of a bearing will change the clearance in the tens of one thousands and could interfere with heat transfer, that backside film when burnt from heat could create bearing move or walk from loads imo.
@@zdravkomomci7570 Yep... I can't think of any BENEFIT to applying oil there, so... why cloud the issue? Almost like PUTTING weevils in your cereal : )
Forget about the internet mechanics and builders, i like your way your builds have been proven
Exactly
One of the most humble engine builders who has proven success with different engine platforms. Great job Jay thanks for the lessons.
Wow, thank you!
This coming week i shall follow this advice.
Thank you for the education, appreciated. All the way from south africa!
i was taught 40 years ago that 1) oil takes up space
2) why would you lubricate something that is meant to be a friction fit?
3) the bearing manufacturers have instructions for a reason follow them.
If your theory is true i didn't need to buy +.001 bearings for my new crank i could have just greased the back side of them them. Damn i could have saved $40 on main bearings. If bearing clearance is generally .0025" how much you figure a thin coat of 30 wt. oil will make up. when i disassemble engines the rod end under the bearing has oil in there. wonder how it got there?.
@@markthegunplumber8376it's because the oil freezes once it gets behind the bearing shell and no longer behaves like a FLUID anymore, duh (that was sarcasm, I agree with you)
I don't use any type of oil in the back of the bearings while assembling then. Never used and it never made sense to me. However, I've always spent a lot of time aligning bearing to their beds, specially those without notches. After hearing your opinion, I actually realized that putting a little oil in the back of the bearing will actually make my job of worrying about bearing alignment a lot easier. You've got a very good point.
I have an engine to assemble tomorrow, it is an older one with those bearing notches, but I'll give this subject a test again.
I agree with this method. Nice to see some one else doing it. I have been looked at sideways when I have done this method. My father was an engine builder in the 60's-80's. This was his tip to me on the first engine I ever built. Great work Jay. Love these info vids. Keep it up crew!!!
Thanks for sharing
My uncle taught me to clean new crankshaft bearings with copper scotchbrite or chorboy. Then lightly coat them with STP, Marvel mystery oil, or mineral oil. He was a great mechanic. 60+ years in the car repair business, lotsa happy customers too. Thanks for sharing🇺🇸 the video post and best 🍀of luck 👍🏼
I've built hundreds of engines over the past 35 years. Have never had an issue without oiling the backside of bearings. Would like to see how much you're temporarily changing oil clearances causing excessive wear on bearings. Will do some measuring on the next assembly just to see. My bet is there is enough for concern
yes larry a very simple check is to assemble with both methods oil on back of bearing and without , assemble both ways with plasti gauge and measure the difference
flynn plasti gauge is like measuring with a yard stick. Lol.
@@tahcogunworks please explain how many engine you have built and your methods
If the oil couldnt escape and was trapped between the bearing and the housing then yeah it would be of some concern. As its not youre talking maybe 4-6 microns and if your worried about that then you got some serious ocd issues.
@@daveb1870 so you have measured the oil layer after the bearing crush ? And it's .00015748 - .00023622 ? Really ? What'd ya measure it with ? How many engines you built? Excluding the Briggs on your mom's lawn mower. How many are still running ?
40 years doing engines and fit dry on the back when rebuilding but I have done hundreds of top and bottom rolled in mains and also never had a problem. Maybe I will mic some one day but I think either way is fine.
The reaction from people is interesting you either love it or hate it, not like Jay is gonna change how he assembles engines and he has a proven track record so there is clearly merit to the method, I'd certainly give it a try.
I used to build Air cooled, engines for a company in Liverpool, and always put oil on the reverse side of the bearings, even though eddy the boss was not sure, because he used to say I’ve never done that, but I never had any problems with the bottom end of my engine builds, and that was over 20 years ago 👍
I've been oiling the back side of bearings for years.my shop teacher in high school had a brush inside a old plastic carb cleaner cap on his bench and in it was marvel mystery oil thinned slightly with diesel.and would coat both sides.ive been doing it ever since.when you tighten it down it pushes most of it out the sides
Then sir you have been doing it wrong from the start.
@@ezpz7143 I've done probably close to 200 motors and in the last 10 years they have been turbo motors pushing 40 lbs of boost some supercharged motors and a bunch of nitrous supercharged turning 10,000 rpms banging of the rev limiter on jet skis and they seem to last.im gonna keep doing it till I'm proven other wise
3:40 shows the advantage of the lubrication method.
But what did the oil do? It's wasting time with no benefit what so ever.
@@jeremyking5684 when you put the bearings in like in the video the bearings do slightly move when torquing them down.and as they are almost a perfect fit there is a ever so slight movement.with rotation and heat expansion.exspeacialy in aluminum blocks.and under normal use oil pressure does push oil in between the bearing and the block.
I agree with Jay. Been doing this over 3 decades. I have added oil to the backs of bearing but usually when its a snug fit and the seat action takes a lot of effort or is "sticky" when going in which is most installations.
That fact that these motors work at all and the power we can get out them is insane in itself, I love it 🤘
Couldn't agree more!
I’m amazed that any engine can have 10,000 20,000+ hours on them, it’s hard to believe how well they work, when I first learned about piston rings at 6 or 7 I didn’t believe it, “you have metal scraping metal thousands of times a minute, and it’ll last for decades?!?” Motor oil is an amazing thing.
Many years working with engines and I have never heard anything like this. Thank you for educating me, Very good info.
Had a rotating assembly bind up when one of the guys used assembly lube on the back side of the bearings. We pulled it apart cleaned it all off and installed the bearings in dry and the crank rotated.
Obviously this is not oil.
Thanks for sharing
Ok, do it the way you want, won't argue. Will say though, the back of the bearing transfers heat to the cap/ block and having clean surface for that heat transfer is important. This is part of the reason for bearing crush. Myself....dry on back, lube on face. My thought is lube plus heat equals poor heat transfer, and also has a very slight effect on clearances. But- do as you like.
I took your advice and put it into practice on a Mazda 2.3L DISI Turbo... worked as you described.
6 one way. half-dozen the other. Cleanliness of all parts + correct/gentle install is much more crucial.
Jay is right. Very simple! Folk lore is one thing but proven track records are a different story. They man is beyond meticulous and knows his stuff. Dare anyone to argue that!
Great video. Always good content. Well balanced discussion on the topic.
Can't wait to see the tear down of the 96mm 2jz engine.
I always use red Loctite or red hi-temp silicone sealer. I should not have written that. No doubt someone will do it. Our IH 806G has some interesting stains on the rod and cap where the shells ride. We always used a thin lubricant on the shells. Our junior-high/high school shop student-teacher taught us that in the 1960s. After getting his teaching degree he ran a 289 in a rail at our local drag strip. The dragster was reasonably reliable… and very fast. His ‘Clutch-Flite’ never failed on race day.
Curious if you've measured clearances with the lube behind the bearing and without?
It absolutely does tighten bearing clearance
Don't do this people!!!
Be hard headed if you want!
Great machinist i knew many years ago always said the back of the bearings is important cuz any foreign material will transfer imperfections through the bearing face
2:00
I kinda see your point there. Putting the oil on the back side allows the bearings to move into proper place as the cap crushes it down. And as you torque it down, we can see the red fluid being pushed out along with the black stuff.
Kinda like how window tint is put on with soapy water, they dont put the tint on dry OR when you 1st drop the piston down the cylinder wall, they say to rub wd40 on the cylinder wall so that as the piston is dropped in, the rings dont "scrape" the wall, the wd40 acts as a barrier to allow the piston to smoothly drop in without scrape.
So, where as normally we do not put oil there and therefore we are putting a dry bearing surface to another dry metal surface, then as you tighten down the cap, you have 2 dry metal sides being pressed together and if there is a slight mis-alignment, now you potentially have a scratched bearing or crank or rod side.
The question i have, IS all the red stuff being pushed out or is there some left under that bearing which CAN cause an issue like everyone is seeing as a thrown bearing .. ??
The video shows the red fluid being pushed out, but is all of it being pushed out ??
I've been building engines since the mid 90's and never lubed the back of the bearing on install. I also never get the sheared off "dirt" when i install them. The block is generally not 100% dry on install either, some amount of rust preventing lube is needed on all blocks. I wipe the back of the bearing and the housing clean with a non-lint cloth and away we go. Purposely oiling between the bearing and housing will change clearances, maybe not enough for a failure, but the change is not predictable or measurable during final assembly and should not be done. When disassembling a properly built engine, you will find little to no lube on the bearing back or the housing. If you are still convinced that you need to do it, use something very thin, like WD40.
This is good advice guys.
He also has a video where he oils his brake shoes too on the friction side.
I also reduces friction.
LOL
I've always dipped the bearing in a container of oil, even use the zinc lube that is important for break-ins. Done lots of HD diesel engines, everything was dipped, caps, bolts unless assembly stated dry.
I put bearings in Cadillac engines for 20yrs at dealership , dry when on the engine stand and when in the car they no doubt got oil on them, never had any issues that came back for bearing problems. If it were my engine they would go in dry than oil, I learned that anything behind a bearing could cause problems. Yes oil gets behind them, the mains through the oil galley hole. I guess I am old school. Jesus Does Save
Like this guy, I have always oiled the backside of a bearing with a thin oil on assembly. I've never spun a bearing although I stuck to stock engines not heavily modified. I doubt it makes a difference, but that's what I did.
We used to rebuild NTC-855 Cummins diesels in the frame. You would do one main at a time and we would clean as best as possible, then roll the top main bearing into place around the crank, install and torque the cap and done. These would run 350-400k miles with no problems. While they didn't turn 8000 rpms, the pressures in a diesel are considerable under load.
I saw in Thailand workshop that in frame they wipe mains with clean rags then spray clean diesel onto the mains cover with rag for an hour before putting on the bearings in. Its hot there and they abuse all things that move but just wondered if this was done by others?
I agree. Same method! Got into several arguments w an old boss about it. Never had a failure.
Thank you for sharing you knowledge with us dummies 🤙🏻🤙🏻
So glad this topic finally came up!
im a car mechanic .
i learned rebuilding engines from my father
he is a mechanic since 1969 .
he taught me to put a slight amount of 10w oil under the bearings .
the reason , he said, is what you said EXACTLY!!
none of the engines he built failed and none of the engines ive built failed .
the thing is that no other mechanics ,i have conversations with ,do that
Nice I always wanted to know why you did that. Now I was also wondering since you tightened the bearings to take measurements then loosen and retighten for final assembly do you loose some of that bearing crush? Thx
Elastically deformed interference fitment.
So thankful for the videos you post. They are worth so much for us guys that don’t have a mentor to guide us through the learning process.
I am with Mike below. you cannot get the bearings and rod too clean. I use lacquer thinner to clean everything. the heat transfer is critical from the rod rotating end. I have never lost a rod and have built dozens of high rpm engines. it may work for you but I will never, ever build an engine like that.
Which side are you on? You start off seemingly agreeing with the vid, but the end sounds like you disagree?
Been rebuilding engines a while and never did that. Thank you for the knowledge, I really appreciate it
This reminds me of a HS physics experiment, where we had sheet pan full of water. We sprinkled talcum powder on the water's surface, then dropped one drop of oil from an eye dropper to the water surface. The oil would spread out over the surface, displacing the talcum, so you could easily see and measure the diameter of the circular patch of oil. Knowing the volume of oil in one drop, and calculating the area of the circular patch of oil, you can divide the volume by the area and calculate the actual minimum thickness of the oil.
Personally, I will agree with the cleaning the back side of the bearing shell, but I think I'll still refrain from oiling the backside of bearings.
I have done both and great success both ways. Long as your measurements are spot on and do things properly should be no issues. Just like you said need to get familiar with doing it.
this video would be more convincing if you compared a dry vs oiled bearing with a bore gauge to see what the change is between both
thats key, it works for sure and i wouldnt doubt that considering there are tolerances, and if its out of tolerance or very close within most times itll lightly self clearance and become non issue. but then after a while, that oil will be gone and your clearances would be higher. from my perspective it would be ok to do, but its maybe 25% maybe more, of cases the engine will not last as long. By then something else might have failed. its all chance
@@thecarrepairdummy7021pulled that outta your arse 😂 you have a pro builder and randoms are arguing with his technique.
The oil squeezes out, if you think it’s gonna throw off the tolerances, you’re crazy.
@_..-.._..-.._ was probably drunk when I posted that, honestly it looks like I was rambling 🤷♂️🤣
It's the crush that holds the bearing in the cap.adding oil on the backside will cause less oil clearance . Too tight will cause the crank to lock up a light oil like you did probably doesn't cause any problem . Good video you hit the points well , I personally don't do this but sounds like you have good luck doing it . I scuff the front of the bearing also the rear .
I was told never put oil behind bearings in fear of oil coaking, burning the oil that isnt being displaced, which in theory will shrink tolerances.
I've gone through countless engines over the years and the only time I've seen a main or rod bore get remotely hot was when a bearing hammered out and spun. Bearing bores have a honed cross hatch like a cylinder wall so oil makes it's way through the groves anyway.
@@bobroberts2371 the bearing should seat well against the main and rod bore with any clearance to be between the bearing and journal though, there should be no space for oil behind the bearings. They crush at the seams (as the video explains) and I really don’t think the goal of honing a main or rod bore is a similar RA as a cylinder, it’s only used to make it proper size. 🤷♂️ I’m no expert but the people I work for claim to be
@@kylekeck9617 The bearing bore and back of the bearing are not polished smooth so oil will eventually wick behind the bearing when the engine is in operation.
I'm well aware that the primary goal of line honing is to side the bearing bore. My point is the honing leaves peaks and valleys, this allows oil to migrate between the bearing and bore.
I don't intentionally put oil on the back of the bearing however, thin oil does not pose any problems.
Read all Suzuki motorcycle manuals say to put smooth moly paste behind upper rod bearing to transfer heat
I see it from both sides, I learned no oil . I'm interested in the clearance differences.
I trust anything Jay says about building engine's and wouldn't second guess him. Bonneville baby... 331mph.⭐🏁🏁🏁🔥🔥🔥🔥⭐🏁🏁🏁🏁🏁🤤👌
Here come the keyboard mechanics.
😂
Good one
Experts in writing skills, but nothing else LOL
What's a keyboard?
It cracked me up pretty good, thanks 😁
Why not put oil and wipe it off just making it a slippery surface, so it wont effect the clearance as mentioned by experts in the comments.
Thank you for sharing your knowledge 👍
Kawasaki recommends lubing the back of the bearings on various models....the old ZX-11 is one I distinctly remember. They actually recommended moly lube. I have always off set the bearings in the cap/saddles so as they self align when crushed
.
Also, watch a modern engine assembly done by robotics. Never do they put oil on back side of bearings.
Totally agree with this video, been doing this for well over 40 years.
What happens when you take a motor apart and remove the rod bearing? There is oil on the back side right? So what's the harm in adding oil on the back during assembly?
Change clearances in the beginning,those galleys aren't used untill full assembly then primed.
I've never put oil in the back of a bearing due to measuring for clearances but I agree that we should see a video with clearances with and without oil on the back. If it dramatically closes off the clearancing that could be an issue to begin with
I did an apprenticeship in a reconditioning shop and then a further 20 years and i cant say that the engines i have ever pulled apart had oil under the rod bearings they were pretty much always dry. I learnt all about tunnel sizes nip, crush etc but not to put oil under the shell nor have i ever seen anyone else do it.
@@1997obspsd Yes we need someone to do a video on that using two of same motors and bearings. One with and without oil.
No there should not be any oil under bearing when you take one apart if assembled correctly will not be any room for oil to get behind bearing.
@@ahmedsimmons4465 Common sense tells you that any oil foolishly put under the bearing shell will get squeezed out when the caps are tensioned as the bearings are designed to be an interference fit when the caps are tightened this is where the nip and crush come into play.
“Absolutely, attention to details are key”😊
I like to do final assembly with the bearing backsides dry. But I agree it all comes down to crush. Similar to a press fit component, oil there won't matter. I've even seen people use tin foil or newspaper on a back side to tighten up a clearance.
If you spun a bearing because of a bit of oil on the back of a bearing you had a major issue somewhere.
Important to remember that mains on some engines have oil pressure at all times behind ~1/3 of the bearing width too.
newspaper won't transfer heat
Thank you for these fresh tips. I do appreciate the detailed information, and for this reason, I subscribed. 👍
If it makes you feel good and it doesn't hurt anything.... do it!🏁
@@AZDESERT2024 yeah.... wonder how many engines of Jay's have blown....🤔
I never oil the back of the bearings, but back in the day I did a lot of in-chassis rebuilds, and a lot of bearing roll ins. Damn things will drip oil for like a week so it's kind of unavoidable to get some oil on the back. I never worried about it and it never hurt anything. I used to have most in-chassis done in a day, and a bearing roll-in done before lunch, so there was no time to let them drip until it stopped. Truck and equipment downtime is way too expensive to worry about crap like that. At the time we were billing the trucks out at 100 per hour, and that was 30 years ago. No time to pretend you're working for NASA
Never oiled the back of a bearing before always just clean them really well but I’m open to trying it on my own personal engines. If it works for Jay on the high power builds he does I’m pretty sure it’s okay to use a really light oil on the saddles anyways Would love to see more on that B20 build I’m sure it’s been done and running but hey can’t hurt to ask right ?! 🤷🏼♂️
Exactly, just clean/inspect the mating surfaces very well.. I’ve gone as far lightly rubbing them with a tack cloth..😆
My man Jay still one of the Top, if not the Top guys in motorsports
Ive never known anyone who spun a bearing from putting oil on the backs of the bearings...ive never once had a problem. To each thier own
That was more interesting than I thought it would be. Using a small amount of ATF (a much thinner fluid) on the backside is not the same as putting assembly lube on the front side. Still, I've never put any oil of any sort on the backside of bearings and I don't think I'm going to start now.
get some premium bearings that fit
Thank you for your videos, I disagree with lubricating the back of the bearing shell for assembly. I think it would be good next video showing what rod bearing nip is, how it is measured and the engineering purpose behind it ie to provide interference fit between the bearing shell and bearing journal housing. Adding oil only increases the likely hood of bearing shell movement at break in. The problem is other less experienced people see this as a must do and bests practice when it is not. Please do not take this as a negative I like your videos and enjoy learning from them.
Dave I appreciate your input. And respect your right to disagree. This is how we have found success without failure. However, We had the same concern with people possibly thinking our open discussion could be misinterpreted as us saying it is a must do or best practice. Which is why we shot this video more than once and took precaution to use language that specifically did not imply this is a must do and did not present it as a best practice. This is a video about how we do it and why. We have had great success building engines that break records and live longer than the standard expectation for other engines at that power per cubic inch level and people often ask for a peek behind the curtain on how we do it. So these videos show how it gets done.
You are not the first person to feel a resistance or hesitation about this method. We have had old timers that never graduated high school quoting their fathers’ fathers all the way to engineers pulling out text books to quote formulas they were taught in school. But it all boils down to many people grew up being told “you can’t apply oil to the back of the bearing or it will move and you will spin it” by someone else and (because it is easy to believe without questioning) they locked that belief system in as gospel and carried it through life.
It’s one thing for people to disagree on a theory that none of them have personally tested in practice in the field. That actually happens all the time and can be healthy in encouraging testing and experimentation to find the truth. But it is a weird feeling to describe when people that have never actually tested the theory and produced a negative result from it argue that it won’t work to someone that spent their whole life putting it into practice with nothing but positive results and not a single negative result yet.
If you’ve been a fan of this channel for some time you may have noticed that we try to present information that is normally hoarded away as proprietary in a way that could be understood by almost anyone regardless of their experience level. There are some technical topics that we either over simplify or skip all together if the explanation has to get too technical. Our team is composed of a diverse group ranging from people that got their GED without finishing high school all the way to engineers that decide what project car to buy next with custom spreadsheets and made up performance metric formula index matrixes. But regardless of their come-up they are some of the best in the industry today. There are many internal conversations where someone says “but I was always told….” or “but this engineering text book says…” or “but it’s just physics, it should…” while the other side of the table is saying “I hear you, but here are the actual results of the actual testing” it’s a good counter balance. We believe that the theories taught to us by our parents and teachers and schools help pick a direction in narrowing down the path for our own investigation and experimentation. But the results are the results.
One of the questions we ask each other a lot around the shop is “how do you know what you know?” If the answer is “someone told me so” or “I read it in a book” then it should be classified differently in your head than the things you actually know. Maybe it happens to be true, or maybe the person you heard it from was mistaken. Or maybe their statement was only true under a certain condition that they left out at that time. Or maybe they were just repeating something that THEY were told and never tested and it’s just passing down through the spoken word over time like a fable.
Either way we enjoy these types of topics because they generate healthy arguments that create results from speculation that everyone can learn from. So we appreciate you joining the conversation and hope you will continue to do so in future videos. I appreciate that you disagreed respectfully and constructively and You do help the channel be interacting.
Yea! What he said! ^^^
@@realstreetperformance this is the best breakdown explanation I’ve ever heard in life. Thank you!!!
@@realstreetperformance what type of Trans oil, how thin?
First time I've ever heard anyone go into this subject , always wondered about , looks like next time I will be adding bearing cleaning and back side light lubricating to the engine builds. 👍
That's why all the big horsepower supra guys go to Jay for engine builds because the guy knows what he is doing. Just ask baltic supra and jrod.