1- Home X-Y axis then Z axis 2 - Lift Z axis 30 mm 3 - Retract Filament 4 - Set temperature to 0 C and wait until its cool 5- Remove the fan cover and then the silicone sleeve 6- Set temperature to 240 C and wait until its hot 7- Unscrew nozzle using 12mm wrench/ pliers (careful, its hot) 8 - Install the new nozzle using your hand first, then tighten with pliers / wrench 9 -Set temperature to 0 C and wait until its cool 10 - Install Silicone sleeve, fan cover
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
Had my KE suffer a bad blockage today (new printer lol) was my mistake. I had to dismantle everything down to the heating block and had to remount it. Get it as STRAIGHT as possible as it's essentially laying out the filament, you don't want it angled in case it could cause any discrepancies in your prints
I tried replacing the nozzle and accidentally cracked the hotend with my pliers and now it's not heating :( I will try replacing the hotend now. Make a tutorial of that too please.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
i feel some extra notes need to be added: be extremely careful not to accidentally let the fan wires touch the hot-end mine did but i got lucky if you go slow threading the nozzle it will heat up expand and try to unthread itself so watch out for that get an armrest anything reall to put your elbow at the printers hight for the best accuracy and comfort (very important!)
How about a tutorial on where to get the header pcb board for the KE and fit it after a blob of death desides to mess the printer up big time... After only having it a month.. I can't find one anywhere in the UK to repair my printer...
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
My printer created the blob. When i wanted to move up z to look it autohomed with a 2cm blob below the nozzle and started bending the bed moving down as the gight pin could not reach the bed. I quickly but power. Why is there no move op z without auto home option?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
@@chazwickie81 Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Just chiming in here.. that 2194 is almost always the cr touch pin taking a crap. I ordered a new one on Amazon and swapped it out. Been perfect ever since and I was getting that error on every print
@@hdjoe22 Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
How about a tutorial on where to get the header pcb board for the KE and fit it after a blob of death desides to mess the printer up big time... After only having it a month.. I can't find one anywhere in the UK to repair my printer...
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
1- Home X-Y axis then Z axis
2 - Lift Z axis 30 mm
3 - Retract Filament
4 - Set temperature to 0 C and wait until its cool
5- Remove the fan cover and then the silicone sleeve
6- Set temperature to 240 C and wait until its hot
7- Unscrew nozzle using 12mm wrench/ pliers (careful, its hot)
8 - Install the new nozzle using your hand first, then tighten with pliers / wrench
9 -Set temperature to 0 C and wait until its cool
10 - Install Silicone sleeve, fan cover
can someone explain it to me why it needs to be hot when changing the nozzle?
fyi the wrench needed it's a 12mm one
Thanks. And the nozzle is a 6mm if you want to use one different from the included one.
Thanks, guys!
6mm nozzle is so much easy to screw in using a 6mm deep socket and a mini socket wrench
Be very, VERY careful to not rip the rubber sleeve. Also, does it matter if the heating block is angled in any specific direction when you are done?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
Had my KE suffer a bad blockage today (new printer lol) was my mistake. I had to dismantle everything down to the heating block and had to remount it. Get it as STRAIGHT as possible as it's essentially laying out the filament, you don't want it angled in case it could cause any discrepancies in your prints
Bambu labs: Lets make it unclip, lift out and click in new one. Creality will never think of that...
I tried replacing the nozzle and accidentally cracked the hotend with my pliers and now it's not heating :(
I will try replacing the hotend now. Make a tutorial of that too please.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
i feel some extra notes need to be added:
be extremely careful not to accidentally let the fan wires touch the hot-end mine did but i got lucky
if you go slow threading the nozzle it will heat up expand and try to unthread itself so watch out for that
get an armrest anything reall to put your elbow at the printers hight for the best accuracy and comfort (very important!)
How about a tutorial on where to get the header pcb board for the KE and fit it after a blob of death desides to mess the printer up big time... After only having it a month.. I can't find one anywhere in the UK to repair my printer...
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
My printer created the blob. When i wanted to move up z to look it autohomed with a 2cm blob below the nozzle and started bending the bed moving down as the gight pin could not reach the bed. I quickly but power. Why is there no move op z without auto home option?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
the replacement nozzles I got have a much, much shorter screw length, is that a major issue?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Yes, yes it is a major issue.
yeah filament will leak out
I bought the ender 3 v3 ke. After less than 2 months the nozzle was defective. Very disappointing!
U sure its not just clogged
How long does it take
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
My printer stopped extruding mid print😔😭
same here
@@thatonecanadian6403 idk what to do
@@coolestkid5 neither do I, im trying to see if it's something with the nozzle. I cant remove the filament from the printer though.
@@thatonecanadian6403 im going to put a new nozzle and see if that works i will reply after update
I just changed the nozzle to a brand new one 0.4 mm and its magically working again. It was really caked up. I followed this exact video.
pro tip: if you lost your hex key, you can use your filament cutter instead
thats a dumb tips
What is error key 2194, please?? It's happening to almost everybody!!
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
What dose the nozzle temp show?
@@chazwickie81 Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Just chiming in here.. that 2194 is almost always the cr touch pin taking a crap. I ordered a new one on Amazon and swapped it out. Been perfect ever since and I was getting that error on every print
@@hdjoe22 Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Moi j’arrive pas à tourner
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
How about a tutorial on where to get the header pcb board for the KE and fit it after a blob of death desides to mess the printer up big time... After only having it a month.. I can't find one anywhere in the UK to repair my printer...
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)