Your presentation are Really help me to understand FACP. Only one dout while you are integrated the hooters based on zones all the hooters are blinking may confuses the zone . Can you kindly explain
just one question, if we perform a test in the zone 1, the light or siren in the zone 1 have to work ?, and wy the rest of the sirens (zone 2, 3 and 4) work also?, at really I don´t know
You don't get confuse which zone has fire since control panel will show which zone sensor has been activated which would help the paging system operator to guide the occupants which zone/area should be avoided when evacuating. But of course I repeat, all sounders should be activated so that all occupants would evacuate.
i need more video of detection and fire alarm system from you i really like that field i am living in USA i work for a fire alarm company in New york city.
Malaking tulong po to for info bout fire safety..may updated price po b kau and specs n subok n mairerecomend?for upcoming videos nio po suggestion for more better result paki focus po sa detailed part Ng videos .
just want to ask practical question. If one smoke detector in zone1 in fire alarm status and the Fire alarm panel activated to Fire alarm with sounder is being activated, my question is does other smoke detector in the same zone (zone1) would still alarm (knowing that the zone circuit in question is in Alarm mode already)assuming the fire reaches to other adjacent smoke detector? Granting the fire alarm was not reset in the panel and the smoke or heat still in alarm mode and only silenced at the Fire alarm Panel. Why or Why not? thank you.
Yes sir when 1 of the detectors in the zone (e.g. Zone 1) has sent the signal to the control panel (zone indicator will show alarm in zone 1 meaning the fire is in zone 1), the panel would activate all the sounders at the same time. When the fire reaches the other detectors on the same zone, those detectors would still give signals to the control panel though indicator in zone 1 is already activated. You would see the indicator light of the detector itself turns from blinking to steady red when it detects fire. When fire reaches to other zone, the indicator light of the fire detector once again would change from blinking red to steady meaning the fire reaches that device and at the same time the indicator light of the control panel will also be activated meaning the fire reaches that zone.
@@junreyeguna maximum of how many detectors can one zone with detectors could still detect fire assuming that some detectors already in fire alarm mode. And also how much voltage drops does one smoke detector consumed in alarm mode? What is the minimum voltage in an IDC/zone circuit that could still send fire alarm signal to panel to activate the alarm.
Sir the maximum number of detectors in a zone depends on the model of the control panel. In the video, the control panel can hold up to 4 detectors in every zone without affecting its efficiency
usually false alarm is caused by dusty/moist environment (in cases of smoke detectors), wrong choice of cable, loose termination, wrong or faulty resistor or maybe signaling wires came across with your AC source so these are some of the things we need to avoid when wiring our initiators.
Sir pwede po mag asked lang po..about po sa pag testing niyo sa smoke detector or heat detector noong nag testing na po kayo bkit po ung strobelight niyo po nag alarm lahat hindi po doon lang sa designated area lang po ung mag alarm..
Yes sir normal po tlaga na lahat ng strobe light ay mag alarm kasi po ang purpose ng FDAS ay para ma-aware lahat ng occupants ng building to evacuate kahit wala pa sa kanilang zone ang sunog. Makikita nman po sa indicator light ng mismong control panel sir ang location or zone ng naka activate ng detector.
Hello sir goodday po sa inyo tanong kulang po kung wiring ng firemans teliphone jack naka paralel lang ba sya sa loop ng fdas or may sarili syang wire at kung may sarili po syang wire anung wire po recomended tungkol sa firemans telephone jack.
Yes sir, if any of the sensors detects fire, all sounders should be activated so that all occupants of the buildings should be aware that there is an on-going fire so that they can immediately evacuate. Say for example, there is a fire in the 3rd floor of the building, all building occupants should be aware and evacuate and not just those who are in the 3rd floor or whichever zone being involved.
Notifier Ang brand na gamit Namin sa Robinson sir tyaka yung setup po Namin sa manual pull down at smoke detector magkaibang home run maski pareho po syang addressable sir nagkaka trouble sya kaya ginawa ko na lagyan nalang sya ng sariling home run yun naging ok na pati sa module nya at tyaka sa panel Namin..
Pwede nmn sir pero di matitrigger ang facp if ever may lose connection or defect ang devices, much better maglagay ng resistor sa dulo ng line pra maiwasan ang mga to.. EOL (end of line)
NC2 nalang po kulang sakin sir.. naka experience ako mag FDAS dito sa Robinson mall at hangang Ngayon sir nagamay kona sya at natoto narin ako tungkol sa data wiring at termination Kong paano ko sya pinag aaralang mabuti hehehe salamat pala sa supervisor ko na napaka bait at handa syang magturo para matutonan Ang FDAS oh auxillary hehehe god bless po sir Ricky. At Sayo din sir may mga nakuha parin akong lesson Sayo hehe
Fire Alarm Systems looks easy to wire. But how the people inside the building know with Zone is the one that triggers the system without being in front of the Panel
During actual installation, cables should be a fire-resistant signaling cable but in the video, I just used the ordinary signaling wires for the demonstration.
@@junreyeguna may ncII na kasi ako nung 2012.. naexpired.. wala p dati fire detection and alarm.. kukuha ulit ako ng assesment.. dito ko na lang matutunan ang fire detection and alarm para sa assesment..
good job Mister Junrey Eguna i really like and appreciate the way you make people understand how fire detection and fire alarm system work .
I appreciate for the comment sir. Thank you so much
This is very easy and understandable..the technician must explain when installing and connecting
Your presentation are Really help me to understand FACP. Only one dout while you are integrated the hooters based on zones all the hooters are blinking may confuses the zone . Can you kindly explain
just one question, if we perform a test in the zone 1, the light or siren in the zone 1 have to work ?, and wy the rest of the sirens (zone 2, 3 and 4) work also?, at really I don´t know
You don't get confuse which zone has fire since control panel will show which zone sensor has been activated which would help the paging system operator to guide the occupants which zone/area should be avoided when evacuating. But of course I repeat, all sounders should be activated so that all occupants would evacuate.
@@junreyeguna is true yoy have reason, is necessary activate all sensors to know that exist a emergency, thanks a lot bro
i need more video of detection and fire alarm system from you i really like that field i am living in USA i work for a fire alarm company in New york city.
I have already 6 more videos about FDAS and its components. God bless
During testing you don't need to break the ARMAC glass , all you need to do just use the key to release and test .
Well understood, thanks for the effort put in place.
question : Could i place the sounder alarm in the middle of the loop
I want more of this valuable information and thank you for that
So nice video Thank you sir.👍👍👍👌👌👌
Malaking tulong po to for info bout fire safety..may updated price po b kau and specs n subok n mairerecomend?for upcoming videos nio po suggestion for more better result paki focus po sa detailed part Ng videos .
Yes sir thank you for your suggestion. I'm planning to give more details in the inside of the control panel on my next video about FDAS
sir pwede po ba duplex wire no. 18 gamitin ko
I know that the wiring for fire alarm system should be one piece without cuts, is that true? and if yes how to wire it?
Good video, why is zone 2 red light flashing continuously even when there's no smoke or dust
It doesn't matter which zone (area) is on fire, all occupants must evacuate thus all sounders should be activated.
Sir tanong ko lang po, pag ba magkakabit ng fdas ano po mga kailangan natin sa pag proseso na ng installation maliban sa mga equipments?
ask lng bos bkt naka battery trobol p rin kht napalitan na ng bgo battery after mareset..mlimit tuloy tumunog ung warning nya..
just want to ask practical question. If one smoke detector in zone1 in fire alarm status and the Fire alarm panel activated to Fire alarm with sounder is being activated, my question is does other smoke detector in the same zone (zone1) would still alarm (knowing that the zone circuit in question is in Alarm mode already)assuming the fire reaches to other adjacent smoke detector? Granting the fire alarm was not reset in the panel and the smoke or heat still in alarm mode and only silenced at the Fire alarm Panel. Why or Why not? thank you.
Yes sir when 1 of the detectors in the zone (e.g. Zone 1) has sent the signal to the control panel (zone indicator will show alarm in zone 1 meaning the fire is in zone 1), the panel would activate all the sounders at the same time. When the fire reaches the other detectors on the same zone, those detectors would still give signals to the control panel though indicator in zone 1 is already activated. You would see the indicator light of the detector itself turns from blinking to steady red when it detects fire. When fire reaches to other zone, the indicator light of the fire detector once again would change from blinking red to steady meaning the fire reaches that device and at the same time the indicator light of the control panel will also be activated meaning the fire reaches that zone.
@@junreyeguna maximum of how many detectors can one zone with detectors could still detect fire assuming that some detectors already in fire alarm mode. And also how much voltage drops does one smoke detector consumed in alarm mode? What is the minimum voltage in an IDC/zone circuit that could still send fire alarm signal to panel to activate the alarm.
Sir the maximum number of detectors in a zone depends on the model of the control panel. In the video, the control panel can hold up to 4 detectors in every zone without affecting its efficiency
@@junreyeguna in a conventional FACP, how to minimize false alarm signals from idc devices?
usually false alarm is caused by dusty/moist environment (in cases of smoke detectors), wrong choice of cable, loose termination, wrong or faulty resistor or maybe signaling wires came across with your AC source so these are some of the things we need to avoid when wiring our initiators.
Sir ask ko lang po. Convensional f.a. ang sounder connection po ba ay pwde isang wire conection lang +?
master ilan po ang pwedi mong i kabit sa zone 1 po pwedi po umabot ng Sampong Smoke Detector ?
Sir pwede po mag asked lang po..about po sa pag testing niyo sa smoke detector or heat detector noong nag testing na po kayo bkit po ung strobelight niyo po nag alarm lahat hindi po doon lang sa designated area lang po ung mag alarm..
Yes sir normal po tlaga na lahat ng strobe light ay mag alarm kasi po ang purpose ng FDAS ay para ma-aware lahat ng occupants ng building to evacuate kahit wala pa sa kanilang zone ang sunog. Makikita nman po sa indicator light ng mismong control panel sir ang location or zone ng naka activate ng detector.
Hello sir goodday po sa inyo tanong kulang po kung wiring ng firemans teliphone jack naka paralel lang ba sya sa loop ng fdas or may sarili syang wire at kung may sarili po syang wire anung wire po recomended tungkol sa firemans telephone jack.
Master Yung strobe light ba pwede bayan e terminate sa sounder,? Salamat
Where can you buy these? I need practice in real life !
I have doubt.... Why the 4 horn strobe get activated when any one of the detector gets detected....
Is that 4 horn is a circuit or what..?
Yes sir, if any of the sensors detects fire, all sounders should be activated so that all occupants of the buildings should be aware that there is an on-going fire so that they can immediately evacuate. Say for example, there is a fire in the 3rd floor of the building, all building occupants should be aware and evacuate and not just those who are in the 3rd floor or whichever zone being involved.
Sir, thank you for sharing your ideas . more video .
Yes sir, soon if time permits. Thank you so much
May be you are interested sir, I already have uploaded more videos about FDAS components and testing. Thank you
hi, do you have picture layout of your control panel box?
Sir gusto ko po matuto about FDAS please make more videos about this thank you and more power godbless👍
salamat po. i'll be posting related videos once it will be made available.
Addressable po ba yn boss?
@@cromselectrical2659 conventional lng po yan sir.
mas maganda master kung related sa ncII.. pls.. ty..
kailangan ko kasi fdas at cctv..
Great 👍👍👌👍👌 good luck 🤞
.parepareho lang ba ang instalation..kahit iba iba ang ang brand ng panel..kase po may 3phase po..tulad ng aseware..
Magdepende po yan sa brand at model sir. Refer nlng po tayo niyan sa kanyang installation/user's manual na kasama sa unit po.
Please Tell Me Place In Myanmar.
Want To Buy Smoke Detector
مرحبا هل من الممكن ان اربط الاجراس واحدة مع اخرى في حال كونها اكثر من واحدة في نفس الzoon
Thank you sir good explanation..
And amazing..
Salamat master👍.good bless
Helo sir,, may i ask if where to put the diodes,?, same brand asenware..
Sir, ilang ohms po ba ng resistors ang kailangan para dyan.??? yung standard na po na ohms na kailangan..thnx
24k ohms para sa conventional..47k naman para sa addressable..
Amazing ❤ Thank you
so easy to understand thanks
is the heat detector reusable?
Amazing 😎🤗
Notifier Ang brand na gamit Namin sa Robinson sir tyaka yung setup po Namin sa manual pull down at smoke detector magkaibang home run maski pareho po syang addressable sir nagkaka trouble sya kaya ginawa ko na lagyan nalang sya ng sariling home run yun naging ok na pati sa module nya at tyaka sa panel Namin..
Ok lng po pala ilagay diretso ang resistor sa terminal ng facp?
Pwede nmn sir pero di matitrigger ang facp if ever may lose connection or defect ang devices, much better maglagay ng resistor sa dulo ng line pra maiwasan ang mga to.. EOL (end of line)
Is this FACP Asnware brand?
yes sir
hi sir. can I use this video as a reference for teaching my students
Yes sir you may use the video if for educational purposes. Subscription also to my channel is highly appreciated. God bless
NC2 nalang po kulang sakin sir.. naka experience ako mag FDAS dito sa Robinson mall at hangang Ngayon sir nagamay kona sya at natoto narin ako tungkol sa data wiring at termination Kong paano ko sya pinag aaralang mabuti hehehe salamat pala sa supervisor ko na napaka bait at handa syang magturo para matutonan Ang FDAS oh auxillary hehehe god bless po sir Ricky. At Sayo din sir may mga nakuha parin akong lesson Sayo hehe
Sir how many device installed in zone 1 or maximum device installed in zone 1
NIce one sir.. nag subscribed po ako..
Tnx po maam
Is a sprinklerbell used as output?!
Strobe light
great vedeo
Pwedi po Bayan sa line to line connection? Ask ko Lang kung pwedi
Sir, is that a conventional or addressable system and why ? ... Many thanks in advance
the video uses a conventional fdas
Why were there no end of line resistors?
very nice job
thank you Sir.Godbless
Thank you too
Awesome video!! Thank you
Glad you liked it, thank you so much.
without JBFA ? Direct to MCFA is okay?
Can we compound sound storbe?
Sir pano po alisin ung fault relay na error sa goalstar na panel. Nag iingay po sya lagi e. Goal star 16 zone version 2
It would have been better to do the video with the camera. And it would be helpful to understand the connection by saying the name of each device.
Fire Alarm Systems looks easy to wire. But how the people inside the building know with Zone is the one that triggers the system without being in front of the Panel
It's for the fire department to know so they can see how to tackle the fire.
another electrical auxiliary system a building should have is the cctv, telephone and the paging system sir.
Sir smoke detector lagane ka price kitna h
Is the cable being used a fire resistance cable
During actual installation, cables should be a fire-resistant signaling cable but in the video, I just used the ordinary signaling wires for the demonstration.
Dear sir,is it last point need 6.5k Resister
Good question, I thought he would connect a 5.6k ohm resistor to the break glass device
Salamat sa sharing bossing.
salamat din po sir
Nice video, God bless you
Thank you
Bhai market kah h iski
Sir anong brang yan fire alarm panel?
at sa pag wring po master Pwedi po bang makapalit ang SD At Motion DETECtor PO
\
Bkt wlng resistor master pwd pala yun.
Thank you sir
Hi sir gustu q poh sana kumuha ng nc2 sa tesda for EIM anu poh ang trial?
Assessment package is written, interview and actual demonstration of lighting fixtures, outlets and cctv or fdas
sir, gawa din po kayu video ng wiring diagram nyan,, thanks
Thank you.. God bless🙏
Thank you too
Sir please send your mob number
Big thanks bro
sir will u translate in english it most important and helpfull thanks
Nice galing naman master
Nice
What is the size of wire?
for the AC source, it is advisable to use at least #16 AWG size of conductor while for the signaling devices conductors should be 0.5mm2 to 1.5mm2.
U shud have brought th camera up close to the control board maan we cant see the details
Nice Work But
Pano po connection kung merong room indicator,?
Beautiful
I never knew how easy fore alarm was😂
Thank you sir 😊
good
Eol sir meron ba resistor.
السلام علیکم bahi jan
Bkit music dapat ng sasalita ung maririnig
Sir yong termination don sa panel gusto ko sana makita sang terminal mo po nilagay thanks po
Sir I have uploaded more videos already about control panel termination and so as with control panel circuit boards.
السلام علیکم g
Plz show the connection of wire in panel in zoom mode.
ua-cam.com/video/aNEgwVbA9nU/v-deo.html
.sir saan ung bell nya jan?
Yung apat po na kulay pula sa taas ng control panel. Horn with Strobe light na po siya
Bang bisa belajar GK ya? Or.. ada no TLP bang?
Anlayo sir dapat ilapit mo ung camera mo
one of my first video po kasi to sir during pandemic kaya di pa ganun ka ayos ang pagkkuha ng video.
EOL mo master bakit walang Resistor
naka fix na po siya sa device sir
ganyan po baang gagawin sa nc2..? EIM.. Maraming salamat master..
Isa lng po sa kelangang matutunan ng EIM NC II
@@junreyeguna may ncII na kasi ako nung 2012.. naexpired.. wala p dati fire detection and alarm.. kukuha ulit ako ng assesment.. dito ko na lang matutunan ang fire detection and alarm para sa assesment..
@@andyguieb1898 yes sir CCTV installation, Door Access Control at FDAS installation lng nman po ang naidagdag.
@@junreyeguna salamat master..
Easy testing
Boss paturo naman ako
saan school po pwedi mg aral ng Fdas
Any technical school po sir na nag ooffer ng EIM NC II or sa TESDA training center na malapit sa inyo.
Thank you sir ...
Most welcome
uh oh strobes aren't synced...
really use a box grommet on your main panel rookie
Sir! Good eve., ok lng ba subscribe ako. Vloger npla kayo
cge salamat hehehe
Nac fault kese nikale
Mas maganda kung close up ung video..