Thanks buddy, it looks like its stable in this clip, but I could barely get it to full trigger without spinning out or recking it this night! I went 83mph the pass before this one, but I spun the tires and tumbled it violently! lol. I think I can fit a slightly bigger pinion so will see what happens!?
@@maxs6231 I have never seen or used a Rlaarlo controller. This was the carbon roller so I'm using a Radiolink Rc4gs V3 controller and I do recommend Radiolink Rc4gs V3 or Rc6gs V3 for a low cost but very good controller if you end up needing something new!
I have the 130amp spektrum esc in it with the spektrum 3200kv 3660 motor with a 35t pinion gear, I haven't touched anything on the truck except installing the electronics and tires and lowering the suspension! A 120amp esc should work great for you, good luck man👍
Hey bud! So I have a tire issue. I bought a 4s certified racing tire but even at 60 percent it spins to fact and the tire gets to thin, but I been using a 6s now at 50percent on the dial and anything over 45mph the wheels turn into paper lol.
bruh i cant imagine my car going twice its current top speed. that's heroic!
Thanks man!
That’s really fast for that truck!🏁🏁🏁
Thanks buddy!
Nice runs brother! 🤜🤛
Thanks for stopping in buddy!👍
Outstanding run! It looked really stable! Where do you go from here? Bigger pinion (if you can fit it), higher KV motor or something else?
Thanks buddy, it looks like its stable in this clip, but I could barely get it to full trigger without spinning out or recking it this night! I went 83mph the pass before this one, but I spun the tires and tumbled it violently! lol. I think I can fit a slightly bigger pinion so will see what happens!?
@@micron3268 Well good job getting a clean run in! I was impressed!
Now that's fast enough to "get to the choppa!" 🚁🛻💨
🤣
Btw do you have issues with the driveshaft cups?
I have not had any trouble with the truck so far! Thanks for stopping in!
Just 4s? is that it
Yes, 4s is in it! Thanks for taking a look!
@@micron3268 did you get the Spektrum 130amp Esc
Spektrum 3660 3200kv motor from Amain Hobbies?
@@micron3268 have you had any problems with the controller like I have?
@@maxs6231 I have never seen or used a Rlaarlo controller. This was the carbon roller so I'm using a Radiolink Rc4gs V3 controller and I do recommend Radiolink Rc4gs V3 or Rc6gs V3 for a low cost but very good controller if you end up needing something new!
@@micron3268 Okay thanks I might do that.I Have the RTR carbon and the controller is just absolutely terrible.
What amp do you have and did you do anything different with the gearing. I just put a 120amp esc on it
I have the 130amp spektrum esc in it with the spektrum 3200kv 3660 motor with a 35t pinion gear, I haven't touched anything on the truck except installing the electronics and tires and lowering the suspension! A 120amp esc should work great for you, good luck man👍
@@micron3268 i used a 3652-3300kv last night I thought other was fast but this moved
Hey bud! So I have a tire issue. I bought a 4s certified racing tire but even at 60 percent it spins to fact and the tire gets to thin, but I been using a 6s now at 50percent on the dial and anything over 45mph the wheels turn into paper lol.
If you're using it for speed runs try foams, but for bashing I really don't know what to tell you man!
@micron3268 ya just for speed runs. Bc in quite sure w
The way I have it set up right now it goes somewhere between 70-90mph for sure