capacitor is good, no need to change capacitor. the power transistor is short circuit so it is not blocking voltage. in normal condition each capacitor's voltage must available at each transistor's collector to emitter. if any transistor is short circuited, then it will not hold VCEO, in result all voltage will appear at the opposite transistor. so the power supply cannot take startup
@@HaseebElectronics What is the cause of the transistor burning.. Is it an overload or distortion in the pwm signal or the discharge elements and the transformer coil have a faulty diode, capacitor and 47k fast resistor
@@HaseebElectronics it didn't appear that you made any mention of the caps possibly being shot, You didn't check the E.S.R Burning smells are fine, if it just blew up now, but if it's been a week or 2 the smell wouldn't be there You touched it with your fingers then.. thought nothing of it Great you swapped the Transistor, You didn't check other possible faulty components as a result of the short
the capacitor ESR test is needed when the supply don't drive the load or it fluctuates or the power MOSFET or fuse burns out if the circuit works fine, then mostly I skip the ESR test
@@HaseebElectronics Sure... Respectfully mate (My Fellow Electronics brother) I've been doing this since i was 6, I'm 49 we all have our things, don't we. there are foundational rules such as (always test voltages first) but then we all put our own stamp ME... I have seen too many situations where i should have tested E.S.R. on Caps and... time and experience has taught me that i should Besides it only takes you say a few seconds more to test 2 or 3 caps or maybe 1min to test them all when i repair, i basically do what you did, i follow the voltage i find the fault , i replace one thing at a time BUT I ALWAYS DO HOUSEKEEPING AFTERWARDS if all seems ok, i'll check basics like ESR on caps Resistance on Fuses Just in case and i have had scenarios where i have seen High resistance on fuses even though the circuit works and high ESR on caps when it was all working and changing them out as well since it's open saves time fucking around later on but hey, again, we all have our own way we do things that's how i would have done it but yeah, mainly because you had all that blackened stuff, I NEVER LOOK PAST THAT
I have 6v 30 amps with exact problem but when I opened the box i saw they totally removed the transistor serial numbers by polishing the plastic surfaces.. do you have any suggestions about which kind of transistor models are compatible for this power supply please? Is this model what you showing is compatible? Thanks
Hello dr sir how are you can you explain this fold er in diagram and explain why the coupling capacitor is dropping one hundred fifty volts and why we don't have any output thanks
Very fast repair brother but some information need you replace defrent transistor i see and last question SMPS can use as lithium battery charger ? Thank you and best regards from Philippines 🇵🇭☕☕☕
I have one smps power supply it has some problems it has an output and also it works for long time but suddenly it stops working an output off why this huppned ?
change the capacitor 250v330uf
capacitor is good, no need to change capacitor. the power transistor is short circuit so it is not blocking voltage. in normal condition each capacitor's voltage must available at each transistor's collector to emitter. if any transistor is short circuited, then it will not hold VCEO, in result all voltage will appear at the opposite transistor. so the power supply cannot take startup
@@HaseebElectronics What is the cause of the transistor burning.. Is it an overload or distortion in the pwm signal or the discharge elements and the transformer coil have a faulty diode, capacitor and 47k fast resistor
Moj BRATE bilo mi je zadovoljstvo slusati igledati Vas rad,puno,puno pozdrava i zravlja od Milorada
veliki pozdrav i pozdrav. Budi blagoslovljen
Teşekkürler.
çok teşekkürler
Minute 6:25
Yes🤏👌💫💯
best regards
Makasih ya sdrku sudah berbagi informasi nya 👍❤️
Güzel iş güzel video. Yaşasın haseeb elektronik.İyiki varsınız. Saygı ve selamlar.
saygılar ve özel teşekkürler
Yet another good educational repair. Thanks Haseebibi!!
best regards and special thanks
Nice repair! Loved it.
Very good and useful information sir thanks for sharing this knowledge to us
it is my pleasure
Good work brother 👍
thanks a lot
Good work 👍👋
thanks a lot dear friend
Excellent sharing brother.
best regards
Thank you very much sir for the useful video.
best regards
Good work👍👍
best regards and special thanks
Emeğinize sağlık...
Excellent thanks for sharing
thanks a lot
Thanks for sharing
it is my pleasure
Keep them coming man!!
it is my pleasure
1:57 Who do you ignore the black marks under the caps ?
i was checking that, is there some burning sign or smoke sign
@@HaseebElectronics
it didn't appear that you made any mention of the caps possibly being shot,
You didn't check the E.S.R
Burning smells are fine, if it just blew up now, but if it's been a week or 2 the smell wouldn't be there
You touched it with your fingers then.. thought nothing of it
Great you swapped the Transistor,
You didn't check other possible faulty components as a result of the short
the capacitor ESR test is needed when the supply don't drive the load or it fluctuates or the power MOSFET or fuse burns out
if the circuit works fine, then mostly I skip the ESR test
@@HaseebElectronics
Sure...
Respectfully mate (My Fellow Electronics brother) I've been doing this since i was 6, I'm 49
we all have our things, don't we.
there are foundational rules such as (always test voltages first)
but then we all put our own stamp
ME... I have seen too many situations where i should have tested E.S.R. on Caps
and... time and experience has taught me that i should
Besides it only takes you say a few seconds more to test 2 or 3 caps or maybe 1min to test them all
when i repair, i basically do what you did, i follow the voltage
i find the fault , i replace one thing at a time
BUT I ALWAYS DO HOUSEKEEPING AFTERWARDS
if all seems ok, i'll check basics like
ESR on caps
Resistance on Fuses
Just in case
and i have had scenarios where i have seen High resistance on fuses even though the circuit works and high ESR on caps when it was all working
and changing them out as well since it's open saves time fucking around later on
but hey, again, we all have our own way we do things
that's how i would have done it
but yeah, mainly because you had all that blackened stuff, I NEVER LOOK PAST THAT
salutes and special thanks for your valuable comment
you are exactly perfect
Hello Janab Bhai Sahib
bhai ji kesy hein aap
Grazie ❤️👍
most welcome
You have sort circuit protection and overload protection circuit
Excellent
best regards and special thanks
Thanks...sir ji...
it is my pleasure
Hi
Have you schematic of this type of power supply how can I find it ???
Sir please make video on voltage controlled oscillator
SIr, Sincerely request you to show how to troubleshoot automotive ecm/ecu .
Thank you
excellent.., brother
best regards
How to check smd ceramic capcitar in circuit
👌👌👌👍
most welcome
EEE (excellent engineering enhanced)
best regards
Like topic Power supply
I have 6v 30 amps with exact problem but when I opened the box i saw they totally removed the transistor serial numbers by polishing the plastic surfaces.. do you have any suggestions about which kind of transistor models are compatible for this power supply please? Is this model what you showing is compatible? Thanks
Trace the circuit with what ever other components are still unremoved including switching ic. Match for ckts. You can find it out.
Sir why use dpdt switch and how work this dpdt switch when we turn it 120 volt or 220 vac.
Hello dr sir how are you can you explain this fold er in diagram and explain why the coupling capacitor is dropping one hundred fifty volts and why we don't have any output thanks
hwy not both power transistors change (due to long term reliability) ?
if one is working good, then i think no need to replace. as it is in bipolar drive, so it will work normally
Very fast repair brother but some information need you replace defrent transistor i see and last question SMPS can use as lithium battery charger ?
Thank you and best regards from Philippines 🇵🇭☕☕☕
Look for data sheets or replacement tables..
NO! Used to charge lithium cells will result in uncontrollable fire!
How to is verible vc cc
Nice very nice
it is my pleasure
I have same SMPS 12v 30A. The output negative positive is shorted. What should i check?
How to know which substitute transistor can be used instead of original one , please guide us...
Look for data sheets or replacement tables..
Sir why inductor used in output side
As an energy "tank" or receptacle during the AC zero-crossings.
I have one smps power supply it has some problems it has an output and also it works for long time but suddenly it stops working an output off why this huppned ?
e 13009 transistor use make smps 500w max use long time 13009 ,two transiator
,🙏💯