I really liked watching this video up to the point when you started welding. Can you please put the earth from the welding machine on to the shaft you are welding. Other than that liked your video.Thank You for posting. Regards Peter.
Va sir man gaye aapko ..... But jo aap ye manshin ka speed jo hi vo kese mension karte hi uske bare me bata sakte hi me jo mashin chala ta hu vo all gear tyep machine he to app muze pulli tyepe machine ke gear ke bare me bata sakte hi..... Please sir....,🙂
Welding on lathe is not bad on a bushing type back gear drive lathe it has a nice good contact. And nice job. And me also weld on the lathe even it has roller bearing.
You are right to a point. But the direction of the earth is at the opposite end to the head stock mostly the current would find it,s way through the stead rest (bearings) first then after that through the the head stock ( bearings ) then to the gear set last. This is an older lathe, so none of these points really matter ?? Regards Peter.
Wanderlei Brito rapaz tu disse bom trabalho ? O mohamed soldando no torno o pior o terra nao esta na pc e sim no torno a corrente anda pela maquina inteira ate chegar no terminal da haste . E outra nao usam nenhum epi e muito menos protecao no barramento contra cavaco que cai direto no barramento pra mim o cabra é porcao !
Sir Maine new 24inch chak lagaya hai us me is ka mejar ment sahi nhi aa rha hai kya o chak kharab hai kya,, ptaiye mai kya karu chak waps KR do kya sir ,,,bataye gaye jrur,,
Weld current over bearings of lathe will destroy them ,no need for such a heavy weld. only tack-weld and rest weld some place else . make shaft straight or it will destroy bushing from hydraulic cilinder. weld-sparks can damage chrome shaft ,which can damage seals from hydraulic cilinder.
Probably only works because it's very old and primitve lathe without gears and with bronze/babbitt slide bearings on spindle. So it has big surface to conduct and no gears that can be destroyed by sparks. Welding on a modern lathe will certainly destroy roller/ball bearings by spark erosion/pitting and annealing of the hardened race and roller surfaces. The same will happen to the gears once the bearings are destroyed to the point where they don't conduct any longer due to oxidation, unless the spindle welds itself in place before.
Chuck Norris...you r very much righ sir.the same thing i have noticed on multi axle trucks where the mechanics do welding on wheel hubs to remove broken studs but after welding when the move under loaded conditions their wheel bearing starts making noise.even i seen differential gear pitted due to arc welding.
Дмитрий Дмитрий меня ещё впечатлило, что шток откровенно искривлён, это заметно при вращении. Ну будем надеяться это какой-то гидроцилиндр, который не будет поднимать тяжести.
प्रैक्टिकल वीडियो अच्छा लगता है
Thanks
आपके काम के हिसाब से वर्कशॉप बहुत जल्दी आप की हो जाएगी
Good work sir
Let Shiva be kind to you and the family!
With respect, Vladimir from Russia, Krasnodar city.
Its not perfect but it serve its purpose and customer is cheerfully satisfied. Old school style.
Buen trabajo señor.. te saludo desde paraguay🖒
weldingqulity looks good👍👍
Nice 👌👌 me bhi aurangabad me yehii leat macine ka kaam karta hoo 😊
Vayri veryi good
Thanks for posting. Love the trick indicator.
Sar mane ap ki video dhekhe taper calculat wali appe se samajh aya magar sar whe dig lathe par samjhay
I like your work sir. ..i want to do work with you sirji🙏
el lugar donde trabajas es tu taller o de otra persona.
quien es esa persona que siempre para sentado en tus videos?.
Leth machine pe kaam karte hue chasma use kya kro plz I request u
Super sir ji mai gulshan kumar sahu mai bhi Turner kiya hu aap bahut aacha hai or achha kam karate hai
Thanks Bhai
Good job sirg
Great Indian Engineers.
I really liked watching this video up to the point when you started welding.
Can you please put the earth from the welding machine on to the shaft you are welding.
Other than that liked your video.Thank You for posting.
Regards Peter.
If he puts earthing on shaft spark can damage shaft surface finish.
@@mkpansari I sugest clamping earth on ''eye'' of cilinder. With clamp, for example.
Perfact work
Lath machen ka had out ho jay to kase milay shaft m taper cut lag raha h to kase milay
Ótimo trabalho mas nunca dobre o eletrodo ele solta o revestimento principalmente o 70 18 mas no mais Parabéns ficou ótimo seu trabalho
Va sir man gaye aapko .....
But jo aap ye manshin ka speed jo hi vo kese mension karte hi uske bare me bata sakte hi me jo mashin chala ta hu vo all gear tyep machine he to app muze pulli tyepe machine ke gear ke bare me bata sakte hi.....
Please sir....,🙂
Welding on lathe is not bad on a bushing type back gear drive lathe it has a nice good contact. And nice job. And me also weld on the lathe even it has roller bearing.
You are right to a point.
But the direction of the earth is at the opposite end to the head stock mostly the current would find it,s way through the stead rest (bearings) first then after that through the the head stock ( bearings ) then to the gear set last.
This is an older lathe, so none of these points really matter ??
Regards Peter.
Belo trabalho. E o óculos de proteção?
Where is the protection glasses???
Got all the 3rd world safety equipment- flip flops, no glasses, wide open belts, etc.
I like it bro
Thanks
На все руки мастер)
👌👌👌
क्या ये वेल्डिंग राड 7,5 नम्बर की है
BIEN TRABAJADO OBRA DE ARTE
Bom trabalho de usinagem com uma maquina antiga,sou de São Paulo,Brasil e voçê ?
Wanderlei Brito rapaz tu disse bom trabalho ? O mohamed soldando no torno o pior o terra nao esta na pc e sim no torno a corrente anda pela maquina inteira ate chegar no terminal da haste . E outra nao usam nenhum epi e muito menos protecao no barramento contra cavaco que cai direto no barramento pra mim o cabra é porcao !
Отличная работа 👍
Sir mujhe mm thread ka details app se sikhna sahta hu kya app sikha denge
Parabéns, ótimo trabalho...
Sar aap kon sa. Kating. Tools. Yuj. Karte ha
नॉरमल टूल जो हार्डवेयर की दुकान पर मिलते हैं
Sir video ko shoot krke baad me details me btayie Kya kese karna chahiye tabhi videos aur better banegi aur likes bhi milenge aur hame knowledge bhi.
आप मेरे चैनल पर जाइए वहां पर हिंदी में समझाते हुए बहुत से वीडियो है
@@MechanicalMagraj sir I mean k har video Jo bnate Hain, is liye Jo language har koi janta hai usme bnayie plz
Aap ne jo job banya konsa material hai vo
हमें आप का लेथ मशीन का वीडियो बहुत-बहुत अच्छा लगता है आप थ्रेड काटने का फार्मूला बताएं आपकी बहुत-बहुत मेहरबानी होगी धन्यवाद
मेरे चैनल पर थ्रेड काटने का वीडियो बना हुआ है आप इसे देख लेना
Sir aap kmm kya krtey h
Sir ap kis chiz ke thred katne kisi bat kr rahe h
Which electrode you using for weld
Normal electrodes
What kind lathe is that
Ganesh machine tool
Rajkot Gujarat India
Very good
Thanks Sir.
Namaste. I want make 10 inch boring bar . How to choose good metal for boring tool [ antivibrate tool] it means MS, SS , STEEL BAR .
Nagaraja K you should use En24 as a steel. harden n temper to 28 to 30 HRC than weld a carbide tip to use
Use lorry halfshaft and braise carbide tip on.
Nagaraja K En30
Nagaraja K are you making a boring bar
MS is good but carbide tips is (YG 6)
Bravo vive les Tourneur
भाई बीना सेंटर लगें सीधा नही होगा और क्रोम राड पर सिय्पटी जरोरी
Konsa sahat bhai
Sir machine khi taper khsye nhikaalya
Sir ji 12 feet machine ka koi kmm ho to btayiga plzzz
Leath, macin, par, fes, karne, wakt, bit, andar, dhsta, he, koe, upchar, btay
Sir welding rod kon c use hoti h crome pe
Leth work ke liye Kon sa tool use karte h...
Solding tip tool
kitni lathe hai apke paas sir
Supatr sir
Thanks
Nice welding
Thanks
Aapkepash kam hai kya leth ka fourmain hu mai mujhe leth machin challane aata hai
Saft bhi band hai or bush me bhi hole out hai guru dev thoda dyan do
Good job
Thanks Amit ji
Hydrollic shaft bend aaraha hi na bhai bend ni nikhal the kya
Lift axel kaise banatey hai o video banao
धन्यवाद बहुत अच्छा काम किया आपने आप कौन शहर मैं दुकान है
वर्कशॉप मेरा नहीं है मैं किसी और के पास रहता हूं
Ótimo trabalho, ficou muito bom.
sir g apka yh work shop kha h
Megarj. G. Aacehe. Kamvale. How
👍
wah kya kam keya hai 👍
Thanks Sharma ji
Sir meri machines mey lineing bhot ati hai Kay kami hai usmey
Sir bearing me screch aagye honge
@@MechanicalMagraj yes sir
अगर बैरीन्ग सही है तो मोटर पुली लुज होगी
Sir we're is ur work shop
Sir Maine new 24inch chak lagaya hai us me is ka mejar ment sahi nhi aa rha hai kya o chak kharab hai kya,, ptaiye mai kya karu chak waps KR do kya sir ,,,bataye gaye jrur,,
088005566006
👌
Когда вы научитесь делать стружколом ????
4jo ko tru kaise kre
Super
Thanks Sir ji
👏👏👏👏👏
Adjust is must
Weld current over bearings of lathe will destroy them ,no need for such a heavy weld.
only tack-weld and rest weld some place else .
make shaft straight or it will destroy bushing from hydraulic cilinder.
weld-sparks can damage chrome shaft ,which can damage seals from hydraulic cilinder.
jan jansen...u r very much right...the high current during welding can destroy bearings completely...i have witness it my own
It has not happened so far 25 years
Probably only works because it's very old and primitve lathe without gears and with bronze/babbitt slide bearings on spindle. So it has big surface to conduct and no gears that can be destroyed by sparks.
Welding on a modern lathe will certainly destroy roller/ball bearings by spark erosion/pitting and annealing of the hardened race and roller surfaces. The same will happen to the gears once the bearings are destroyed to the point where they don't conduct any longer due to oxidation, unless the spindle welds itself in place before.
Chuck Norris...you r very much righ sir.the same thing i have noticed on multi axle trucks where the mechanics do welding on wheel hubs to remove broken studs but after welding when the move under loaded conditions their wheel bearing starts making noise.even i seen differential gear pitted due to arc welding.
Just put your earth-cable on workpiece
tum har ke chez bana te par..wildig iskiren ka haidal nahi banaya
👍👋
Heeehh safety first india bobo better hit your eye 👁🗨
good job
Hi bhai
Sir thered cauting sikhaye
Amen Bhai mai koshish karuga.
Mag Raj Bheel ok sir
Индикаторная стойка оригинальная
Дмитрий Дмитрий я так и не понял как она работает, никакой шкалы не видно. Просто смотреть за отклонением прутика?
scaryfear21 Да)))Просто на «глаз « смотрит расстояние кончика прутка до заготовки)))))Сотки ловит)))
Дмитрий Дмитрий меня ещё впечатлило, что шток откровенно искривлён, это заметно при вращении. Ну будем надеяться это какой-то гидроцилиндр, который не будет поднимать тяжести.
Nothing but respect for the machinist but come on 😩
Please Tell me a good name for my UA-cam channel
Mechanical Magraj I'm lhete machine operator 8 year experience
Ok
आप कुछ भी लिखो तो हिंदी में लिखना
Sir...... मशिन कीं क्या कीमत हे,,,???
Google पर सर्च करो
Kitna difficult hai chalti machine k saamne video bnana.
Cuidado com camisas de mangas compridas
Sir plz Hindi me baat Karo .kush samajh nahi aa Raha.so plz.
Ничего так )
Oh my God 🙄
Ok Mo 8650028859
Hey liar, it's just only 175k views. Not yet 200000.
अपना कांटेक्ट नंबर देने की कृपा करें
👌
Nice job
Thanks
Good work
Good work
Thanks