Absolutely right! Friggin watched twice now. I had to show my dad this. So you also got another view from his device! Absolutely fantastic man. I'm going to have to watch it and slow the video down some. Maybe .75 speed. Very gracious movement expressed. You are a joy to watch 👷👷👍✌️
You could do with a car blower level control switch to control the air flow from either on or off to 1 to 4 although it looks to be a good idea on the surface
Hola ya estás comprendiendo uno que quiere aprender necesitamos ver cómo hacen las cosas y t agradeceré las medidas GRACIAS RECIBE UN SALUDO DESDE AZCAPOTZALCO CDMX GRACIAS
A tip from a welder run less amps so you can run a longer bead. Now you are pushing through the steel instead of homogenizing. The longer the bead the stronger they are especially rapid expanding welds like these. Those welds look good but lack of fusion will occur. Because of temperature changes the welds Wil have enormous amounts of stress. Tack welds won't hold as good. Because I see alot of high end stuff, like the abricor torch. 😜 So I know with some tips we can help each other ❤️✌🏻 If the volts can be changed set it to 18. 6 /19. 2Volt Wirespeed around 6.3 m/min that should give you around 150 to 190 amps more than enough. If you want to start safer 5.5 m/min should be more than enough. 18.6 volts. Running lower is also possible 16.7 volts at 3.5 m/min. Use a cross over way of welding bolts or any other pieces that need to stay a certain way. You can do it 👍🏻👍🏻
Loved every minute of this build. You sir are one of the best out there. You have a skill set that most people would dream of including myself. 👏🍺
Thaanks brother
Absolutely right! Friggin watched twice now. I had to show my dad this. So you also got another view from his device! Absolutely fantastic man. I'm going to have to watch it and slow the video down some. Maybe .75 speed. Very gracious movement expressed. You are a joy to watch 👷👷👍✌️
@@jacobcoughlin2408 Thanks a lot bro for Nice comment 👍🔧🔧
@@MrDKDIY ХЕРНЯ
Great idea ! I have a question is it safe to breath if u use it in side a room?
Thank you for the great video. Have a great day 👍👍👍👏👏👏
Waoowh very wonderful super amizing good job because of your vlog tutorial I got some knowledge from you about that your vlog
Thanks a lot sir. Watching from phillipines...
U welcome
Superb Bhai jaan
Es esto lo que andaba buscando, gracias saludos desde Bolivia
Saludos cordiales desde Chile Antofagasta
Always creative
I am impressed with the waste oil burner ♪
Thanks
very nice creative design..
Good job brother 👍
Thanks
E bravo be bate 👍👍
Fala 👍👍
Good job.
Many many thanks
Muy bueno gracias X las ideas ....
Конструкция мне понравилась, буду повторять.
Congratulations 😀
Nice job 👍
Super König
👍👍😊
Good job
Thanks
complimenti molto ingegnoso!
Good job👍👍👍🙂🤝
👍👍
Hard working man
Yeah
Pretty cool man.
Молодец ! Я буду делать для обогрева теплицы.
Good job my friend 😜👍
Thanks
Great job Great Video Thank You have to get to building
Thanks
Nice built 👌 but i feel bad for the car where that Oil came from 😜
tNX
Das ist ja alles ganz schön, aber was ist mit Karsten los?
Thank you for this job i love jobs like this
Thanks A lot
Great project Mr mk and so practical to access🔝
Thanks bro
Wonderful innovation!
What impeller did you use?
Very nice build
Thanks for Nice comment
Absolutely brilliant!
Thanks a lot
Love it thanks. been searching for a long time.
Damn i think im the second most subed MR DK cool but im the most subed MR{ _ }DK so thats cool
Super video💪❤
Thanks Angela and Happy Birthday to you 🎂🎉
Fantastic all the way around!!! Dude that is the sweetest set up for a take down foundry I have ever seen! Very well done!!!
Simple and practical idea 👍
Thanks
Bravos👏👏👏
Too thanks
👏👏👏👍👍👍رائع
That’s nice 👍
👍👍😉
Hey! You took my advice! Awesome dude! Getting the works from me. Comment like and sharing with everybody I know. Great build!
Thanks a lot my friend 👍😉
Excellent. Clappppppppppppppppppppppppppppppppppppppppppppp
Tnx broo
Rare and useful 😜
Parádna práca, super 👍😎👍✊
👍👍😉
Super 👍
Thanks al lot
Nice💪
Bravo! Thank you!
👍👍
Great and helpful.
Well done and simple that's cool . keep up the cool Vid's .
very good idea! but no dimensions, tell me the dimensions of the circle, the length and the square?!?!?!!?
Nice
Good💪❤
Thanks
Muy bueno ,lo que andaba buscando
Thank you
@@MrDKDIY mañana empiezo a hacerlo
Gracias por compartir
Super
This is excellent 👍👍 I have no need but I just want try it.
You could do with a car blower level control switch to control the air flow from either on or off to 1 to 4 although it looks to be a good idea on the surface
Cool
Ok felicitări
Nicee 👍
Thanks a lot bro
About how long will it burn with a gallon of waste oil? Awesome work.
Thanks
Amazing
Thanks
can i suggest you watch some videos on how to use a wire feed
Vristi idejata Kako i sekogas iznenaduvas
Hahah fala brat
good
simple and effective, something I like. I was supposed to say no electronics, but the power supply. 😁💪👍
👍👍😂
if you get a motor that runs off line voltage directly you dont need the power supply.
Set that unit in a small woodstove inside and connect a small chimney and you have a shop heater.
Good💪
una pregunta. al tubo vertical porque le hace huecos por el otro extremo de donde va soldado el tubo cuadrado?
Hola ya estás comprendiendo uno que quiere aprender necesitamos ver cómo hacen las cosas y t agradeceré las medidas GRACIAS RECIBE UN SALUDO DESDE AZCAPOTZALCO CDMX GRACIAS
Magkano magpsgawa ng 1 unit wala kc kong time gumawa at wslang gamit thanks
Why don't you use a crucible, to melt your metal or aluminum in??
If the oil got hotter it will give better results.
👍👍👍
👍👍😉😉
Очень хорошо спасибо
👍👍👍👍
Thanks bro
How much time will bunr 1 litre waste oil? Please answer me.
I do not know I did not measure time really
Шаговым сверлом любой чермет сверлится довольно легко?
💪💪💪
👍👍😉
You've already got a 12v power supply going so I'm wondering if you could just set up a glow plug to get the thing lit?
What rato of fuel do you use to the oil
Does this stove save fuel?
It doesn't say fuel it burns fuel!
Show parabéns
Если немного констукцию доработать будет вообще хорошо.
Многу уба бекатонката 😁 и јак проект нема збор
Ne e bekatonka specijalna tula e za ova 👍😉, Fala za komentarot
احسنت
شكرا لكم
If you mix the fuel and oxygen into powder it will burn much better
need a high speed fan???
😉😉
use compressed air or a blower that blows harder...maybe try a way to get the oil atomized better...propane would be even better
He would need to filter the oil to atomize it. It would be a good idea
it'll atomize fine without filtering
filtering never hurts
🔔🔔🔔👍👍👍🛠🛠🛠
👍👍👍😉😁
The little spider: WHAT THE HELL!!! (17:16)
Ok
💪😁☀️
Like
A tip from a welder run less amps so you can run a longer bead.
Now you are pushing through the steel instead of homogenizing.
The longer the bead the stronger they are especially rapid expanding welds like these.
Those welds look good but lack of fusion will occur.
Because of temperature changes the welds Wil have enormous amounts of stress.
Tack welds won't hold as good.
Because I see alot of high end stuff, like the abricor torch. 😜
So I know with some tips we can help each other ❤️✌🏻
If the volts can be changed set it to 18. 6 /19. 2Volt
Wirespeed around 6.3 m/min that should give you around 150 to 190 amps more than enough.
If you want to start safer 5.5 m/min should be more than enough.
18.6 volts.
Running lower is also possible 16.7 volts at 3.5 m/min.
Use a cross over way of welding bolts or any other pieces that need to stay a certain way.
You can do it 👍🏻👍🏻
Cena brat na gerot
👍👍😉😁
Ne e za prodavanje 😁
Ok nego kade go kupi i cena kolku go kupi
I kade go kupi gerot
To ke ti kazam pisi minna FB
Sorry mistaken Mr DK
not even close to hot enuff for a forge , nice idea but for steel nope.ps im a blacksmith.
BASICALLY ITS A OIL BURNING FORGE.
not hot enough for real metal and easy to tip over burning the house down