Water Converted into Explosive Gas - The Ultimate Hydrogen Generator - HHO
Вставка
- Опубліковано 13 гру 2023
- In this video, I will show you how to make a Hydrogen Generator that produces HHO gas. Electrolysis is used here to separate the Hydrogen from the Oxygen in Water. The HHO produced is highly combustible and can be used as a fuel source.
I used Stainless Steel Hardware which is more expensive than normal steel or zinc-plated steel, however, it ensures that the electrodes do not corrode or contaminate the generator or the gas.
For the electrolyte either Sodium Hydroxide or Potassium Hydroxide should be used, using table salt will not produce as much gas and it will also produce chlorine gas and turn the water yellow.
------------------------------
Making a Simple Hydrogen Generator
hydrogen from water
how to make hydrogen
how to make a generator at home
#hho #experiment #hydrogen - Навчання та стиль
🎉🎊🎉Congratulations to @chiranjeebswain4313 and @suheladesilva2933 for winning the 1000 subscriber giveaway, there will be many more giveaways in the future so stay tuned 🎊🎉🎊 Also id like to say Thank you to everyone for your support :)
And how did you build de circuit conversor to 12v?🤔 very good video! 👏👍🏼
@doccosta8336 Thank you, I appreciate it :) the circuit you can buy for relatively cheap from aliexpress or somewhere online, its called a boost converter
@@doccosta83361
Now cook you dinner on the HHO.
Hydrogen stoves are the next big thing
@@WackyInventions why didn't you turn that into a stove?
At some point I want to relearn physics and engineering to build it, but Murphy's law will always be right above my head.
There isn't a better time to start than now 😁 Start small and build your knowledge and skills and proceed with caution. Murphy's law is the basis to my life, and so accurate 😂
@@WackyInventions Thank you!!
They're really easy to build. There's just no practical use for it. If you try and burn hydrogen from it, you'll cause an explosion like I did. I don't recommend.
My advice is use two bubblers when I was young I made one and only had one it back fired through the single bubbler and went to the main jar which was a pickle jar with the lid hot glued to seal it and increase the pressure of the gas, it blew the hot glued lid straight off and I wasn't sure if my hearing would come back, it did but I learned a valuable lesson there lol.
THATS SO OPTIMISTIC LOL HAHAHAH @@WackyInventions
Out of all the HHO vids I've ever watched, this is probably the most visually appealing set up I've ever seen. Everything just feels crystal clean. Thanks for sharing
I want to thank you for your kind words, although i am not a big channel yet, i put in so much effort and sometimes it feels like a waste of time but a comment like that just makes it all worth it and motivates me to carry on. Thank you 😊
Also I would like to let you know that you've been entered into a 1000 subscriber prize draw, if you read my pinned comment you will see the full instructions on this video. Goodluck :D
@@WackyInventionsyour effort shows, it’s not easy to come by these slightly past beginner geared videos with good build quality!
@Squidkid96 Thank you, ive been running on steam trying to build this youtube channel, all my saving have gone on the videos haha, but i promise its only gonna get better 😁
Something you did that I’ll definitely take advantage of, is use something other than hot glue or super glue and actually say what you used. Adhesive science should be way more common knowledge or maybe I’m just stupid
I appreciate that you used RTV to prevent leaks, and that you even went back and let us know you added another metal washer to the mounts. You know your audience haha 👍🏽
Haha, Thanks, honestly I ran out of washers and thought it would hold like that, but then i was like nah I can't leave it like that😂
I will be doing a 1000 Subscriber giveaway to 2 lucky people. There are 2x £20 worth of cash/gift card prizes in your country's chosen currency. The contest begins from the time this comment is posted up until the 1000 subscriber mark. Entry is FREE, all you have to do is subscribe and leave a Comment. Goodluck :D
(Comments posted before this comment on this specific video have been automatically added to the prize draw)
Winners will be sent an email to reply to which will have full instructions and how to claim their prize. Make sure you use an account where you can edit your comment as this will be used for verification. You will have 14 days from the date I contact the winners to respond and claim your prize. If a prize is unclaimed another person will be selected at random.
This contest is in no shape or form associated with UA-cam, I am in full control and responsibility for the giveaway Entries for this giveaway have now closed, participants have been gathered, look out for the next give away
how will you email them just from the account?
@christoalphonsejoy2431 So basically on UA-cam there is no official way to contact people so i will send the winners an email address where they can contact me on, then i will give them a code that they will need to add into their comment by editing it and that way i will know that i have the correct person, from there i will keep contacting the person through the email.
@@WackyInventions one more question, how will you find the winner? are you gonna use a random comment picker or find your favorite comment?
@christoalphonsejoy2431 That I haven't decided yet, but it will most probably be on a random generator The odds are quite high as there are two prizes equal in value and not many participants. The more views and subscribers I get the higher the prizes will become. :)
@@WackyInventions thanks a lot, i actually understood a lot about this after i discovered your video, sorry to bother but one last question please.. if i win the giveaway, would u give me this generator along with the potassium hydroxide instead of a cash prize?, i like it a lot because it is the most minimalistic, small, clean, fast and easy looking generators i have seen so far, it also produces hho at nicely fast rate that it makes me want that generator over money
8:15 that wasa brave move there
Had to show everyone the point of the safety device. I was confident it would work well because I pressure tested the whole unit before attempting something like that. Not having a bubbler could be really dangerous if some backflow was to occur as there is way more gas in the main generator.
I would like to let you know that you've been entered into a 1000 subscriber prize draw, if you read my pinned comment you will see the full instructions on this video. Goodluck :D
It's crazy how 1 of the most EXPLOSIVE gasses, plus oxygen, when together as a gas form, create a anti-flame liquid when done right.
edit: im stupid. i haven't done much chemestry yet in school so i don't know much. y'all thank's for correcting me :)
I know, its mind blowing, I still cant wrap my head around that concept, how can be both dangerous and safe 😅
it's not an anti flame liquid it just restricts oxygen from fire
@@GIHDOR and can remove the heat. It attacks fire on two fronts. The only thing it doesn't do is remove the fuel (usually)
Water can't put up any kind of fire , It's just very good at cooling thinks down and isolating them from oxygen in the air (because it's liquid ) water has very strong bonds , so it won't react with oxygen , but burning nitrogen will create water vapor , so water can't burn (with oxygen ) , water can be product after burning
@@GIHDORand cools thing down
Very beautiful hydrogen torch/generator. I've actually been intending on building one at some point, I have some moonshine jars and stuff but nothing as elegant as you have, it gives me a steampunk vibe and i absolutely love it.
Thank you, happy you liked it 😁 if possible use plastic, it'll be safer, my lids were basically spring loaded so it would blast the seal open in case of an explosion instead of keeping it in and shattering the glass like a normal jar
you should put some medium-grade wire wool in the final pipe before the needle. this would have prevented a complete flashback to the bubbler. the air space above the water can be enough to cause an explosion, last thing you want is a glass bomb.
Nice design, but risky being glass.
wouldn't any water function as a one way valve?
@lostforwar5619 correct that's the purpose of the bubbler. You're also supposed to have a flashback arrestor as a primary safety and the water in the bubbler as a secondary.
if the flashback to the bubbler pushes enough water out of the way almost like it did in the video, it could ignite the hydrogen.
if you Google flashback arrestor you'll see small inline devices that either have a membrane or a fine/medium wire wool being sold to prevent this.
Edit: ua-cam.com/video/JObaMblT8Bs/v-deo.htmlsi=IZV-QjCBg-p6l5ko
this is a spring-loaded flashback arrestor with multi stage safety.
does the length of the tube matter after the water filter procesS? i've seen short tubes to needle with a constant stream of flame instead of just explosions
The little fright produced the best thumb ever!
Awesome project. Fix the bubbler intake hose! pleas.e Convert the glass jars to 4" PVC with clean out trap. Love the idea with the fender washers. Nice job.
Thanks for the tips. I'm glad you enjoyed the video aswell😊
Amazing video! Very well-thought-out and makes for a perfect example of what green hydrogen can be!
Thank you for the support, I believe hydrogen is the future for our world, just safety is a concern at the moment. I wouldn't really want a high pressure hydrogen tank in my car, however an on demand generator would make sense and would be much safer.
I would like to let you know that you've been entered into a 1000 subscriber prize draw, if you read my pinned comment you will see the full instructions on this video. Goodluck :D
@@WackyInventionsOh! Thank you very much!
Not green. Sorry. The salt water remaining turns to lye. An alkaline that's created by ripping water molecules apart with electricity. Green means no bad side product to dispose of too
Unreal jolly blood good old chap,Amaizing 👍👍👍👍👍👍👍
I just want to say this is incredible and you did such a good job explaining how to build it.
Thank you, Im glad you enjoyed the video, hope to see you again 😁
well, we all know you are going to be king of your own settlement when the zombie apocalypse hits
Love this comment 😂 you made my day, I just want the zombie apocalypse to start now. I watched the whole of The Walking Dead series during covid lockdowns and that was my life, and i miss it.😂😁
Just to be on the more extra safe side, I would add an extra bubbler. One bubler makes the risk of a catrostrophic explosion slim, but a second one will half that to half as slim.
Thanks for the suggestions, it would have definitely been safer :)
Maybe make the bubbler bigger perhaps just so the bubbles has more traveling before reaching the surface. Just my 2 cent of thoughts.
wacky, I would use a plastic or metal container as a safety measure due to the pressure that the explosion makes inside the small space. And you could put a diode after the converter so that if there is unwanted contact between the plates, the current does not return with that amperage and damage the batteries.
It was really difficult to find an appropriate container, just for video purposes i wanted it to be see through and all the plastic containers i found just wouldn't seal properly, i did look thick glass and it withheld the pressure of the explosion, but platic would have definitely been better. I plan to make a dry cell in the future so that'll be stainless steel plates with thick polycarbonate plastic and should be alot safer :)
Don’t do this at home as others have said yes because of toxic heavy metal water contamination from electrodes, but also because it is very dangerous to have the hydrogen oxygen mixed, as you can see by the fire flashing through the line. it would be safer to have separate lines for the positive and negative electrodes, so the hydrogen can be collected in a low oxygen, non explosive state
make one that splits hydrogen and oxygen, and then you can fill a tank with it an go scuba diving!!! AWESOME PROJECT, GONNA TRY TO BUILD MY OWNN
Thank you 😁 pls use plastic for the container, the glass was just for visual effect and isn't safe. Also you can just compress normal air into a scooba tank and use it. 👌
This is a great build, seemingly quite powerful, and is almost giving me a Steampunk-ish vibe which I find really appealing, too. The video is quite informative as well, so well done!
I do have a question, though, and that is; how would you go about separating the hydrogen and oxygen? I know I've seen devices in the past that would put a dividing wall between the cathodes and anode, and have a second exhaust from the separator jar, but I wonder if that's the most effective option?
This guy have copied Nighthawkinlight video. The style and the generator. Nothing innovative here
Thank you for the support 😁, It is possible to separate the oxygen and hydrogen, but for most applications its fine to have them mixed, most people split the two only to join it back together later which is pointless. Hydrogen needs oxygen to burn, and it also burns hotter with pure oxygen than if you were to ignite hygrogen gas in normal air as the concentration of oxygen is much lower in the air we breathe
@jonialhonen1420 bruh i just watched his video and i dont see how the two are even similar theres no magical way of doing electrolysis, you cant reinvent the wheel. Strange how you start doing better for yourself and all these haters appear. Anyway.....
Great work sir!
Thank you, I appreciate it 😊
we have just witnessed the birth of the legendary plastic welder.
This would be a cool science project ngl
Good luck it won't work 😂😂
Great video. Very clean looking, and easy.
The igniting of the gas, would using a flash arrestor of some sort prevent this from happening?
It should prevent it but I haven't used one before, in the future when I build a dry cell I will definitely invest in one of those. Thanks for the compliments 😊
Just curious, but both positives and negatives are next to each other. Would it behave better/worse if the it was + - + - instead of + + - -?
Just a thought, but if you happen to know...
Came for a quick lesson on wtf chemistry, stayed for the beats and engineering lesson.
i and my friend made this for a project wihtout the bubbler, we lit it on fire, it blasted so hard it shook our school
we did it 3 days ago and we are 14 years old
Thats was very dangerous, but I know how you felt, when I lit the water bottle full of HHO , the explosion was so massive, my eardrums started to ring. Next time il know to wear ear protection.😂
Also I would like to let you know that you've been entered into a 1000 subscriber prize draw, if you read my pinned comment you will see the full instructions on this video. Goodluck :D
@@WackyInventions and i have a question, the bubbler stopped your flame from going to the generator, but the second time, nothing happened, it only made a nice torch with the flame... why?
@christoalphonsejoy2431 The First time i used a needle that was too big and there wasn't enough gas pressure to keep the flame from going into the tube so the flame continued burning until it hit the water. For smaller HHO generators you need a medical needle as the hole is much smaller, but you just cut off the sharp end and make the end of the needle round again by squeezing it gently with pliers. If you have any more questions il be happy to try help :D
@@WackyInventions thanks a lot, i actually understood a lot about this after i discovered your video, sorry to bother but one last question please.. if i win the giveaway, would u give me this generator along with the potassium hydroxide instead of a cash prize?, i like it a lot because it is the most minimalistic, small, clean, fast and easy looking generators i have seen so far, it also produces hho at nicely fast rate that it makes me want that generator over money
Thumbnail was actually real😅❤
No click bait on this channel 😂
try combining compressed air with this it will make flame even hot along with control valve the compressed air make flame more attractive and it will concentrate flames to one point i hope you'll get my point anyway love your video ❣️
Great idea, I will definitely try this later, thanks for sharing and I really appreciate the support 😁
Love the use of washers however I think a wide mouth jar and bigger washers will give you better surface area. Great job.
awesome, now the next matter, increase volume produced gas and oxidation of your electrodes
That flame is HALF the temperature OF THE SUN.
70% of the sun is Hydrogen 😁 but that burns at around 15 million degrees celcius at the core and 5500 degrees celcius at the surface
@@WackyInventions Ahhh... still Hotter than hell. xD
OUTSTANDING PERFORMANCE
Thank you 😁😁😁
You should use a 90watt laptop charger as the power supply, you can put multiple in parallel. Then put it through a CC CV buck converter. It requires a fan. Nice design. Do not use 18650 cells without some kind of low voltage cutoff.
do you have a material list with amazon links?
I am amazed by your workmanship.
Thank you for the compliments, im happy you liked the video 😁 got many more Wacky ideas coming.😊😁
a tip for the future if your looking to increase the amount of surface area you have thus increasing total output try etching your metal the goal if to make more nucleation sites for production of o2/hho
I like the design. Nice work
Thank you, much appreciated 😁
where did you get the glass containers? ive been trying to make a hho generator but it was to wacky and didnt seal correctly. perhaps the glass jar works better.
I done alot of searching myself, i couldn't find anything plastic which would have been safer, and there were jars that also had glass lids but drilling into a glass lid would have been challenging. Im not sure what country you live in but in the UK i went to a department store called B&M. I understand your frustration though, hope you manage to find what you need :)
Online is difficult too, best thing is to go to stores that sell home and kitchen items in your country and browse the food storage containers
@@WackyInventions thanks. ill try to find something that works better. The genator you made is awesome. Did you encounter some problems to make the flame at the end of the video?
@@andresmagana9184 There was just one problem, at first I used a needle that was too big and it resulted in the backfire, however using a medical needle and cutting the sharp tip off worked well. Also make sure there arent any leaks in your system as that might result in a back fire too.
A mason jar would work well, the ones with metal caps. It might be a bit harder to seal properly though.
How did you stop the tube from exploding the second time?
Also, I expected to see more usefulness than melting plastic and solder. Looking for that uodate 👍
5:59 - your mistake is that you had to connect it diagonally, then the current spreading area would be around each electrode, in your case it spreads in a straight line from the electrode (+) to the electrode (-).
It is dangerous to play with 2HO gas; use a check valve.
Yeah bro i see that would have probably been better, the bubbler is a home made check valve 😁 the water acts like the barrier between the nozzle and the main generator
If you sand the washers it will increase the surface area and make the generator even more efficient
Thanks for that, when i build another one i will definitely do that, makes sense 😁
What's the tip you use for the tube where you light it?
Accidentally the best thumbnail made😅
Thank you, definitely, haha. I was amazed because I record at 60fps, and this scene was only visible on 1 frame out of the whole 60 in a second as the gas burnt so quickly😂
Dude EXCELLENT song choice, I was able to stay hooked on it the entire time. I think you just made me discover a new way to pay attention 💀
Great video! Do you think this would run a 383cc gasoline generator ? If possible what sort of conversions would I need? Some sort of carb kit? Thanks!
I believe it should, i haven't worked exactly how to power an engine correctly, but I have plans to get an engine running soon. The problem is regulating the flow of gas when revving, but for a constant rpm application just a tube in the carb should do and then adjust the flow of gas.
Not even remotely.
@@WackyInventions Then you failed basic chemistry. Not enough output with the amount of energy required for electrolysis.
Wow. I would use that gas for wedging aluminum for example if that works
Instead of washers and nuts, you could do stainless steel wool, which would be more effective and so much less work.
Oil companies: we will regard this channel woth great interest
They don't care about high school chemistry, lol. Plus, they are already invested in and producing hydrogen ICE. I live next to a hydrogen fuel station and see the hydrogen toyotas all the time.
This electrolysis project is a silly but dangerous science experiment, nothing more.
Great build
Thank you, glad you liked it :)
How long does that flame last for before you need to refill it.
Kinda thinking of using this for a solder machine. Do you think that’s a good idea ?
The water lasts for ages, mainly the needle burns up quicker than the water will run out, but i think its kinda dangerous, why not just use a soldering iron?
Awesome build.
Thank you, I appreciate it alot 😁😊
The simplest flashback arrestor is a cigarette filter which fits tight in the hose
Would love to build this my self, do you have a parts list? I don’t really want to hunt down every single thing I need. Also how much did it cost?
don't do it, extremely dangerous and it produces toxic fumes.
So you have it running off 12v, low amperage... would this rig work with a solar panel with 12v/12ah emergency battery for backup? basically an "exit" sign?
It would run for sure, just not sure for how long, you need to check what the max constant amperage is of the battery, if its low then you would need to limit the current so the battery doesn't over heat
Ottimo lavoro!
could make some small design changes so that it's easy to replace the electrodes when it's rusted and no longer performs.
That looks so cool! 2 questions though... how often does the water need replaced? And how did you make that nozzle for the torch?
Thank you, glad you liked it, the water almost never has to be replaced, because the hardware is all stainless steel so it doesn't rust. The level just drops after hours of use, so a little top up is all it takes, after a few top ups id just replace the water to ensure the concentration of the electrolyte is correct as i dont have a way to measure it. Also the nozzle is basically a surgical needle(very thin) and i cut the tip of it off so i dont stab myself and then made it round again with some pliers as it gets crushed when you try to cut it.
Thanks!!
would something like a JacobsParts FP5139 work in place of the 100w boost converter you used?
Yes definitely, another word for boost converter is a step up converter, the boost converter is only needed to control the current, so you could just forget the circuit boatd all together if you have a powerful power supply. I just checked and that converter has a max of 6amps, so you would get less hho and you would need to make sure the current doesn't exceed 6amps as the converter would overheat.
Хорошая штука, в хозяйстве прегодится!
I have to ask, how did you learn how to make this? This is amazing! Were you self taught? Do you have any books or courses you’d recommend?
I am mainly self-taught. I started when I was young just playing around with electronics and working on cars with some help, ive always been trying to fix everything thats broken myself and learning how things work, over the years ive just gotten better and better. I think the best approach is a hands on approach, if you dont know something you can always google it or watch a video but there is no better way to learn than doing it yourself, just start with small simple things and build your knowledge and confidence.
So when you had feedback into the bubbler after lighting, was this due to a lack of pressure from the generator?
Yeah, basically there was a small leak from the seal in the main generator so I cleaned it and reseated it, also the needle was too thick the first time so i changed it
This is cool but remember this is Brown's gas, VERY DANGEROUS. May just wanna consider splitting each element to it's own area.
Please, could you tell how long did it take (aprox) for the electrolites to get afected by corrosion? Having in mind that Steel used was nothing but the provided on any hardware store. Just want to learn :-)
I used Stainless steel so it was completely unaffected, because Stainless steel does not rust, however if you used normal steel you'd probably start seeing rust after the first day of use
@@WackyInventions thanks but there seems to be many types of Stainless Steel as many other HHO videos insist that 316L is the best for this device. They say others will rust (despite the contradiction you mark, that if It is stainless...then it should not rust).
@Guindasman yeah, ive heard about all those things, a budget friendly option would be to get old kitchen items, eg maybe an old stainless steel sink, stainless steel bowls or cooking splash backs, cooking stainless steel has one of the highest corrosion resistace level for the price(usually 304/304L). As you know rust would be bad if it went in our food, so it has to be high grade.
Unless you're making a unit thats going to run for hours a day for many days. For a home project or science experiment, i wouldn't be too worried about what type of stainless steel you use it will still have corrosion resistance compared to steel.
Well made video! Would it be feasible to plug this into an air intake of a car to increase mileage? Probably with throttle liked dynamic voltage control?!
Saw your answer to similar question in another comment. Would love to see you explore the car idea further.
Thank you for the compliment :)Yeah for a small engine a tube in the carburetor would be sufficient but for a car I think it would have to be more thought out, like maybe a high pressure injection system which you could time properly and avoid having your intake explode 😅
Researched a bit more and apparently for the mileage to go down you also need to tweak the ECU to reduce the amount of petrol that is injected.
this is amazing, i will be scaling this up am making a very normal tool not a weapon. (yes this is a joke i dont really wanna get hunted down)
Sir, you never saw this video
I've watched Christopher Dunn (the engineer, not the other one) do this a few times on Ancient Aliens on The History Channel.
Bro you deserve more subscribers
Thank you bro, I will keep going and see where i end up 😁
Bravo super job
I was thinking could you use Peltier Modules and use the heat from the flame to generate a voltage and use that to charge the batteries to make a closed loop. I have been going over this in my head an its well possible. Obviously you would need a bank of Peltier modules over a burner of some kind.
I don't think it would work, the peltier are super inefficient and most of the energy would be lost.
you would probably see an efficiency increase if you paired the electrodes diagonally instead of side by side
Thats a fair point, I didn't think of that before. I love marginal gains 😅 Thanks
Also I would like to let you know that you've been entered into a 1000 subscriber prize draw, if you read my pinned comment you will see the full instructions on this video. Goodluck :D
when i was young i made a hho generator myself just a lot bigger and i torched stuff. then 8:15 happened to me without a bubbler, pieces flying everywhere haha
What if you upscaled this, x100? What would the power of the thrust be? Or x1000? If it’s running off water, is there a way to make this into a perpetual engine?
Perpetual Engine really easy actually just attach a magnet to an arm in front of your car that pulls the magnet on the car! Just don't forget to put holes to see through!
This seems like it'd make an awesome metal forge/melter, that you can run on renewable energy, doesn't take a ludicrous amount of amperage on your home circuits, and gets wicked hot while leaving no harmful pollutants. I always figured that since getting rid of my gas forge a long time ago I had wanted something that could be more "green" since I have hated fossil fuel since well before Greta Thunberg ... The only thing I'd wonder about is how can you can separate the O2 and H2 properly so that your storage tank is not quite so much of a huge bomb (i.e. have 2 separate tanks, that then mix in the burner assembly on the forge)?
As far as my imagination goes there are two main ways I can think of this being possible. One would be to make a really powerful on demand cell, so you wouldn't need to store any gas. This would probably be the safest, but you would definitely need to build a dry cell as they are more efficient and produce more gas. The other way would be like you mentioned to store it, if you build some sort of compressor and compressed it into a proper gas cylinder (e.g. like an oxygen or acetylene tank) either separately or together, but together would be easier as its difficult to make a dry hydrogen cell that separates the gas. Either way the oxygen to hydrogen ratio is perfect in hho so that shouldn't be an issue. I guess that storing it this way would be safe too with the correct fittings and fail safes , e.g. proper one way flow valves and appropriate nozzles.
But its definitely a very interesting topic, I haven't thought of a use for HHO like that 😁
@WackyInventions Storing it that way would be safe unless you had a house fire, then it turns into the B-word. Separating the two would be pretty damn difficult though.
Butuhnya itu hidrogen setara motor mobil alat berat kapal bisa berjalan stabil...kira kira pengubah air menjadi hidrogen butuh ruang engine serta ruang bahan bakar seberapa luas...???
Can you post full materials and maybe links
It’s better than Mr. Indian hacker Oh yeah, by the way, I love your videos, wacky invention❤❤❤❤❤
Thank you bro, you're very kind 😊😊😊 im glad you like my videos 😁
Is this system separate O2 , H2 ?
whaey good idea ❤
Nettes Spielzeug. Hab ich als Jugendlicher auch gebaut. Aber irgendwie endete es immer damit, dass mir alles um die Ohren flog. Ausversehen natürlich 😬
I always wanted to make a proper one when I was a child, so I made this UA-cam channel to remake all my childhood dreams that I didn't have the money for to build. By the way, I still don't have any money, I just gave myself a reason to do it😂😂
Bro said hexavalent chromium wasn't enough and decided he needed some zinc oxide too
Excellent.!
Glad you like it!
Gallium, water, and aluminum will generate copious amounts of hydrogen very simply, and you can recover the gallium.
Nice, thanks for the info, definitely an interesting topic i will look into 😁
wouldnt wiring the battery terminals in parallel be more efficient than series? more voltage would just mean more heat and with a plate design increasing the voltage wouldnt really do much right? wouldnt you want as many amps as you can get? (p.s feel free to correct me in the comments im always open for new info)
I understand your concern, in this case I believe a series circuit would have been better for the reason that the boost converter has a minimum input voltage meaning that the cells in parralel wouldn't have had enough voltage to power the boost converter, also the total maximum power output would still be the same in parralel and in series.
(Cell information, nominal voltage 3.7v , max amps 8amps (3 cells) for calculations below)
P=IV Power =current x Voltage
This is for series - 3.7v x 3cells =11.1v
11.1v x 8amps = 88.8watts
Parralel - 3.7v x 8amps = 29.6 watts
Each cell produces 29.6 watts and there are 3 so thats a total of 88.8watts aswell
Hope that helps 😊
@@WackyInventions ohhh I see your batteries were lacking necessary voltage but were already good on current so you wired series to increase overall efficiency for the boost converter to do its job effectively thank you for clarifying
I heard about some frequencies, on wather, you should put to become much more HHO with low Energie you use to make run HHO!
Hi, I'm trying to get the flame on the syringe needle like you did, what adjustment did you make to prevent the flame from travelling up the tube like it did the first time? Great job by the way. 2012
Thank you :) so basically first thing is to make sure there are no leaks in your system, a leak can cause a drop in pressure coming out the needle, and also the first time i used a thick needle and it resulted in a back fire, you need thin one, a surgical needle is the best i believe,like the ones you get injections with, but you just cut the sharp point off and use pliers to make the hole round again at the end as it gets squashed when you cut it. Feel free to ask more questions, i will do my best to help 😊 also make sure the water is filled as high as possible so even if there is a back fire there will be less gas to combust in the event of an accident
Great, thanks so much for the quick reply. You really put a lot of work into this channel, I honestly didn't expect a reply so soon, it means a lot. I'll be sure to let you know if any more questions arise. Best regards. @@WackyInventions
@suheladesilva2933 Thank you , it means alot 😁
Sir tou used 4 electrodes, and boost converter too,can you run it for long time or i think it will hot your hho generator in one hour ,
@farrukhawana.r.a.q9194 At that current it can run for long and the hho cell wont get hot, only the batteries dont last long before needing to recharge, but if you use a 12v power supply instead of batteries, it could run it for ages. The four electrodes are just to maximise the area, its like having 2 long electrodes but then cutting them in half and connecting it with wire. The boost converter was just used to control the current if you had powerful batteries or a power supply the boost converter wouldn't be needed, it was just so the batteries didn't over heat because the cell wanted more than 8 amps of current, but the batteries could only handle 8amps. Now i had 18650 cells that can handle 20amps continuous :)
What cutting wheels did you use for your dremal?
I bought some on amazon, they're 22mm in diameter (resin-aluminium oxide) and the brand was silverline, they're quite inexpensive but do the job
Now pipe it into your air intake and retune the engine to use 2/3 of the fuel.
Imagine "makeitreal" makes their lightsaber with this gas instead of propane
1: I would have connected them diagonally instead of in parallel.
2: I would have wrapped the supply wires clockwise, the same direction the nuts tighten
Caustic soda= sodium hydroxide, you can technically use any electrolyte, but things like baking soda will work best
Seems like a good way to make a water powered car.
making hydrogen like this is so energy inefficient
How did you make the nozzle for the flame? Does it need to be anything special to create a small flame like that withought flashback?
The nozzle is just a surgical needle (ones you get injections with) and i cut the tip off with some pliers so that i didn't poke myself by accident and made it round again with some pliers and the best way to reduce flash back is to have a one way valve. Also you need to make sure there are no leaks in the system as weak pressure can cause the flame to travel up the tube.
Do you think a 0.4 mm 3d printer nozzle will work to create the high pressure needed?@@WackyInventions
❤ to the bubbler, our favorite character
Haha, He is the main character 😂 small but mighty
o2 and h2 are being generated together (!!) no way to counter high pressure / no overpressure safety valve for this much uncontrolled gas generation, high risk of shortening the electrodes with no spacers and rather arbitrary placement … from potential explosions with glas fragmentation to (comparatively) harmless failure and burning of your electronics, this thing got everything. But at least it looks cool while it lasts …
Hello, can use normal water in this
what if you rough up the surface of those washers before ? more efficient? Im just guessing forgive my ignorance
It would definitely help as it would increase the surface area 😊
What s type glass is using in video? Its normal glass or specially addapted glass?
"specially addapted glass"
lmfao. Stay in school, kiddo.
On a larger scale this would make an admirable system for a car.
for a fuel cell or an engine? is it stored in a fuel tank or made in situ like this one?
@@justkev1044
You just feed it to your cars air intake
It'll make the fuel burn cleaner and considered an extra fuel by itself so less fuel consumption, if I'm not mistaken I have heard somewhere it's like 30% or so
@@AhmedRw like a fuel additive?
@@justkev1044
Not really, it behave more like a nos or n2o just like race games , but it's not as aggressive as n2o