Hy iam from indonesia (borneo) and iam a teknicial elekctrik in a small industri. And i want say thankyou so much for your education is simple with translate indonesia.
Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.
Thanks, I was looking for how to "auto tune" the vfd. I've only worked with ABB drives previously, there it was several modes for tuning. And now I bought a V20 for a band saw project at home, but didn't understand that P1900 was the tuning function :) Was a bit disappointed when the motor made a bit much whine when accelerating, I guess that tuning the drive will silence it a bit.
Sir I have Siemens v20 drive, In singl phasing problem my drive not trip it is runnin condition but my recruitment is in single phasing problem my drive trip so how parameter change
Hey....great video and great explanation....thanks a lot brother....but can you please explain or add how to run your motor in the reverse direction in CN001 mode??? is it even possible?
@@abubakarsiddique7795 Haven't tried it yet, but with "Cn001 - BOP as the only control source " I guess the only way to reverse the direction is by pressing both up and down arrows on the panel as described in the manual 5.1.1 Introduction to the built-in BOP.
Hi this is from India and I am a biggner.. I have a same drive. I am using extranel start stop push button and for frequency using push button for up down Hz. Now i want to ask when I start vfd then it runs up to last running frequency. But I want when ever i stop and press start it should be running on 0 Hz. Means every time I want to adjust frequency from zero.. I hope u got it plz reply if possible...
@@IGSElectronics yaa i visited ur channel.. All r very interesting and helpful videos...👌 👌 👌 👌 And I watched 3rd video of simenc helpful but still problem not solved
Good day! we buy Sinamics v20, 3 phases L1/L2/L3/PE. I think, we are stupid, because we even couldnt turn on it. We only connected cable 4 wires. As result, converter doesnt work, screen doesnt work too, only indicator LED blink by red. Is converter can be damaged or we are stupid? Thank you.
@@user-xz2bt2px5p PE is earth my friend, 3 phase drives don’t have neutral going to it. Just 3 phases and earth. Remove any wire from PE for now and start up the drive, if still red check all 3 phases to make sure you get from 380 to 415( depending were you are in the world) between phases using electric meter. Attach earth to PE once you confirmed all test.
I found this video when I was in stress, and after watching it, all my problems are solved....explained very well.
Thanks a lot mah dude I work as a electromechanical technician inside the paper craft industry and your explanation was so useful 🇲🇽
Hy iam from indonesia (borneo) and iam a teknicial elekctrik in a small industri. And i want say thankyou so much for your education is simple with translate indonesia.
Your wary welcome my friend.
Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.
Thank You! Helped me a Lot! You could Talk a Bit slower and clearer. Thumbs up from Germany :-)
Hi Julien. Thank you for your kind comment. Glad it helped you out. Regarding speed of talking, it is something that i am working on.
Thanks, I was looking for how to "auto tune" the vfd.
I've only worked with ABB drives previously, there it was several modes for tuning. And now I bought a V20 for a band saw project at home, but didn't understand that P1900 was the tuning function :)
Was a bit disappointed when the motor made a bit much whine when accelerating, I guess that tuning the drive will silence it a bit.
Thank you Sr
Thank you
thank you for making this video, i was wondring if you can my question. is it possible to for this inverter to show the current AC motor i using?
Thanks a lot
Most welcome
hi mate thank you for the tutorials can you make one for setting up speed ref using USS and modbus protocol
Glad you like it, regarding USS and Modbus, I shall look in to that.
yes man thank you, im strugling to replace an obsulete Siemens micromaster 420 with V20 . Its controlled by S7-200 using USS protocol.
hi my simens v20 vfd showing fault 3 , any possibility for reset
hi friend , in my equipment it says that i have a VFD fault , and my 50hz decreases to 45hz , what could be the reason ?
Hi dear,
Did you find the solution to the problem,
Please share us Sir
Sir please make a video ....how to remove F72 error alarm
Press ok bottom
How to get digital output from V20 for run fb and trip fb
also i can't find P1110 option in CN001 mode....will u please help me out with this?
hi can u tell by which method i can copy parameter from the drive.can i do it with pc ?
I might do video on that in the future, so far have not worked on that, so not sure how it is done yet.
@@IGSElectronics thank u for the replay, love ur videos
Hi there and thanks a lot for this beneficial video, I have a problem which is how to solve the error of A504?
Sir I have Siemens v20 drive,
In singl phasing problem my drive not trip it is runnin condition but my recruitment is in single phasing problem my drive trip so how parameter change
Hey....great video and great explanation....thanks a lot brother....but can you please explain or add how to run your motor in the reverse direction in CN001 mode???
is it even possible?
Check the other videos for this drive I have maid.
@@IGSElectronics yes i checked..i saw....did not solved my problem
@@abubakarsiddique7795 Haven't tried it yet, but with "Cn001 - BOP as the only control source " I guess the only way to reverse the direction is by pressing both up and down arrows on the panel as described in the manual 5.1.1 Introduction to the built-in BOP.
Hi this is from India and I am a biggner.. I have a same drive. I am using extranel start stop push button and for frequency using push button for up down Hz. Now i want to ask when I start vfd then it runs up to last running frequency. But I want when ever i stop and press start it should be running on 0 Hz. Means every time I want to adjust frequency from zero.. I hope u got it plz reply if possible...
Hi there, please watch the third video of this drive, it should help.
@@IGSElectronics yaa i visited ur channel.. All r very interesting and helpful videos...👌 👌 👌 👌
And I watched 3rd video of simenc helpful but still problem not solved
How to reset 3 phase motor drive
Can you set the output frequency to 100Hz? Or is 50Hz is the maximum?
Yes you can go up to 400hz. There is run frequency and base frequency. Base to always be to you country base frequency. Run can go up to 400Hz.
With Poti I only can go to 50 hz, how can I change that?
Good day! we buy Sinamics v20, 3 phases L1/L2/L3/PE. I think, we are stupid, because we even couldnt turn on it. We only connected cable 4 wires. As result, converter doesnt work, screen doesnt work too, only indicator LED blink by red. Is converter can be damaged or we are stupid? Thank you.
Hi There. Is your drive singe phase or 3 phase?
@@IGSElectronics 3 phase
@@user-xz2bt2px5p what did you connect to PE?
@@IGSElectronics TN-C system. PE=N
@@user-xz2bt2px5p PE is earth my friend, 3 phase drives don’t have neutral going to it. Just 3 phases and earth. Remove any wire from PE for now and start up the drive, if still red check all 3 phases to make sure you get from 380 to 415( depending were you are in the world) between phases using electric meter. Attach earth to PE once you confirmed all test.
i want to modify pid control in cn008
Hi There. I have never done PID control on this drive, so wont be much help to you on this matter.
Explication en français
نرجو الترجمه لفظيا وليس كتابه 😢😢
super confusing. i hate the device
😂😅