Great videos mate keep them up 👍 One advantage the AOP has over the BOP is that the parameters can be uploaded and downloaded onto the AOP. Making it easy even for a mechanical minded technician to change the inverter. I am in the process of moving away from these obsolete Micromaster 420's and replacing them for Control Techniques C200's.
thanks for the video, can you make a video in how to set the parameter for releasing the clutch brake? I'm using micromaster 440. I've already set P1215 to 1 - but the clutch brake of the motor is not releasing. Hope you can demonstrate that. Many thanks.
Yes. See the link from siemens how to do that: support.industry.siemens.com/cs/document/7714804/micromaster-4-(mm440)%3A-set-up-torque-control?dti=0&pnid=13213&lc=en-CN
Just a wee bit too fast in your explanations, particularly with regard to entering the data into the BOP, some references to the manual would be very helpful, ie what the codes mean and how to get to them. Apart from that very good but I will have to watch it a couple of times to make sure I get all the info' you giving out.
Thank you for your comment. I am working on my speed talking, habit that needs time to fix. Don't forget to watch the other 2 videos on this drive, were I go more in to details for remote controls.
If this inverter was powered from 3f with a 1.1kw motor and now I want to connect it to 1f and supply it to the 2.2kv motor, I have to change something in the settings because the undervoltage alarm was triggered, could it be caused by this alarm?
What is the parameters if I want to increase the speed while the motor is running. Now, I cant increase the speed P1082 because the motor is running. I need to stop the motor to change the P1082.
Hi Ingus! greetings from Spain. I have a single question for you. Based in your knowledge, I try change the following parameters in VDF MicroMaster 420: P2012 (USS Com from 4 to PZD 2) & P2013 (PWZ 127 variable to 4 words) in order to use S7-1200 with USS FB communication. I currently using STARTER software V.5.5 without success (By the way my VFD is no Display, no BOP or AOP). Is necessary have a display to make these changes?. Thanks a Lot....
Hi, I didn't quite understand everything from the video. Not my language. How can I configure the frequency change control on the BOP frequency meter panel itself?
HI IM NOT MUCH OF AN ELECTRICIAN I KNOW RESIDENTIAL HOUSE WIRING AND A LTTLE ABOUT WIRING MOTORS. I HAVE THE SAME UNIT CAN THIS BE USED TO CONTROL THE SPEED OF A 115V MOTOR? IF SO CAN YOU HELP ME WITH WIRING?THANKS FOR YOUR TIME
hello, I'm asking for help, I can't start the electric motor - with a complete and step-by-step configuration of the electric motor, the AOP A0541 does not disappear from the screen...All the time, the voltage at the converter outputs is 87 volts, of the same phase. What to do in such a situation?
Hi There, A0541 is Motor data identification routine active, basically it just tells you that, that's what it is happening, there is nothing wrong with the drive. I believe parameter P1910 should be on 0 for this to go away.
@@IGSElectronics In the parameter P3900 set "3", a message appeared" " not available P to acknowledge"...although I have entered the required value in P307
Hi, i have semans VFD 6se3211-5ba40, it was working i tried to set and now i have lost memory, the only thing works is very slow reverse, how much is key pad, or how much is my vfd worth with this problem, i think fast forward key is stuck, fault could be with this one key, can u help pease ? thanks
Hi There, you will need to get key pad to have a look on all your settings. The 3 videos i have made of this drive, should help you understand what to do.
Any body have idea on parameters to configure the 3 programmable Relays on micromaster 440, i noticed the drive you are using doesn't have programmable relay, have scan through the Manual cant find how to configure relay.
@@IGSElectronics the manual i downloaded seems different from yours, on the page you stated i couldn't fine the output terminal and beside my own drive is MicroMaster 440, it has both output terminals and programable Relay 24/25.
@@bdb7629 Hi there, current, volts and power are working in tandem with each other. Many different aspects can influence the current, so you as far as know, no you can’t.
SPEAK SLOW , IF YOUR INTENTION IS TO TEACH OTHERS , IT LOOKS LIKE YOU ARE VERY TIRED AND IN A HURRY TO FINISH VIDEO SOMEHOW .. HALF THE WORDS ARE SWALLOWED NOT ALL PEOPLE ARE EUROPEANS..
Hi great video. I was thinking of factory resetting the micromaster 440 and realise maybe I shouldn’t. Question is if I reset the micromaster 440 would it lost connection to the motor connected to it. Would love your help if possible.
@@IGSElectronics no it doesn’t have any communication. Normally the number in the LCD screen stay on one number when position e.g 5.00 but when I turn on the machine the LCD screen number jumping between 5.00 to 0.00 and normally those numbers are stationary.
What is the parameters if I want to increase the speed while the motor is running. Now, I cant increase the speed P1082 because the motor is running. I need to stop the motor to change the P1082.
I'm new to the world of industrial automation and you just saved my life man, thank you for the rest of my life ^^
Thank you for watching, glad it helped you out.
Great videos mate keep them up 👍
One advantage the AOP has over the BOP is that the parameters can be uploaded and downloaded onto the AOP. Making it easy even for a mechanical minded technician to change the inverter.
I am in the process of moving away from these obsolete Micromaster 420's and replacing them for Control Techniques C200's.
Thanks for the info! Thank you for watching.
"Jog is self explanatory" ok im stupid
But nah, great video, really helped me! Thanks a bundle :)
Glad it helped.
thanks for the video, can you make a video in how to set the parameter for releasing the clutch brake? I'm using micromaster 440. I've already set P1215 to 1 - but the clutch brake of the motor is not releasing. Hope you can demonstrate that. Many thanks.
Dear sir please make video with motorized potentiometer control full details thank you
Why is it alternating 5.00 then 0.00 when you first attach the BOP?
Hi, can you implement a constant torque load with this inverter?
Yes. See the link from siemens how to do that: support.industry.siemens.com/cs/document/7714804/micromaster-4-(mm440)%3A-set-up-torque-control?dti=0&pnid=13213&lc=en-CN
Dear sir, Model Siemens micromaster 440 (75kw). Power on then message show F0002 but not reset. please help me
Just a wee bit too fast in your explanations, particularly with regard to entering the data into the BOP, some references to the manual would be very helpful, ie what the codes mean and how to get to them. Apart from that very good but I will have to watch it a couple of times to make sure I get all the info' you giving out.
Thank you for your comment. I am working on my speed talking, habit that needs time to fix. Don't forget to watch the other 2 videos on this drive, were I go more in to details for remote controls.
If this inverter was powered from 3f with a 1.1kw motor and now I want to connect it to 1f and supply it to the 2.2kv motor, I have to change something in the settings because the undervoltage alarm was triggered, could it be caused by this alarm?
When I followed all this. The motor won't start it just comes up F0001. Any idea what's wrong
What is the parameters if I want to increase the speed while the motor is running. Now, I cant increase the speed P1082 because the motor is running. I need to stop the motor to change the P1082.
Why did you never commission the G120 drive??
Hi Ingus! greetings from Spain. I have a single question for you. Based in your knowledge, I try change the following parameters in VDF MicroMaster 420: P2012 (USS Com from 4 to PZD 2) & P2013 (PWZ 127 variable to 4 words) in order to use S7-1200 with USS FB communication. I currently using STARTER software V.5.5 without success (By the way my VFD is no Display, no BOP or AOP). Is necessary have a display to make these changes?. Thanks a Lot....
i cant open 1001-1003, how can i open this parameter?
is it possible to open in BOP?
thanks in advance
Hi, I didn't quite understand everything from the video. Not my language. How can I configure the frequency change control on the BOP frequency meter panel itself?
MY friend, don't think i can enplane better then i have already have done that in video. Sorry.
HI IM NOT MUCH OF AN ELECTRICIAN I KNOW RESIDENTIAL HOUSE WIRING AND A LTTLE ABOUT WIRING MOTORS. I HAVE THE SAME UNIT CAN THIS BE USED TO CONTROL THE SPEED OF A 115V MOTOR? IF SO CAN YOU HELP ME WITH WIRING?THANKS FOR YOUR TIME
hello, I'm asking for help, I can't start the electric motor - with a complete and step-by-step configuration of the electric motor, the AOP A0541 does not disappear from the screen...All the time, the voltage at the converter outputs is 87 volts, of the same phase. What to do in such a situation?
Hi There, A0541 is Motor data identification routine active, basically it just tells you that, that's what it is happening, there is nothing wrong with the drive. I believe parameter P1910 should be on 0 for this to go away.
@@IGSElectronics In the parameter P3900 set "3", a message appeared" " not available P to acknowledge"...although I have entered the required value in P307
Hi, i have semans VFD 6se3211-5ba40, it was working i tried to set and now i have lost memory, the only thing works is very slow reverse, how much is key pad, or how much is my vfd worth with this problem, i think fast forward key is stuck, fault could be with this one key, can u help pease ? thanks
Hi There, you will need to get key pad to have a look on all your settings. The 3 videos i have made of this drive, should help you understand what to do.
@@IGSElectronics Thanks
Any body have idea on parameters to configure the 3 programmable Relays on micromaster 440, i noticed the drive you are using doesn't have programmable relay, have scan through the Manual cant find how to configure relay.
Hi Egwu. This drive has digital outputs and can be configured in parameter 731 page 52. As relay output no, this drive don't have it.
@@IGSElectronics the manual i downloaded seems different from yours, on the page you stated i couldn't fine the output terminal and beside my own drive is MicroMaster 440, it has both output terminals and programable Relay 24/25.
Hello there, is it possible to increase the speed(rpm) of a Motor running on a VFD without the current of the Electric motor increasing.
@@bdb7629 Hi there, current, volts and power are working in tandem with each other. Many different aspects can influence the current, so you as far as know, no you can’t.
SPEAK SLOW , IF YOUR INTENTION IS TO TEACH OTHERS , IT LOOKS LIKE YOU ARE VERY TIRED AND IN A HURRY TO FINISH VIDEO SOMEHOW .. HALF THE WORDS ARE SWALLOWED NOT ALL PEOPLE ARE EUROPEANS..
Thank you for your comment, I shall address that.
Hi great video. I was thinking of factory resetting the micromaster 440 and realise maybe I shouldn’t. Question is if I reset the micromaster 440 would it lost connection to the motor connected to it.
Would love your help if possible.
Is it communicating with any plc?
@@IGSElectronics no it doesn’t have any communication. Normally the number in the LCD screen stay on one number when position e.g 5.00 but when I turn on the machine the LCD screen number jumping between 5.00 to 0.00 and normally those numbers are stationary.
How to use local control of it sir
Its all in the video my friend.
Why you set parameter 304= 230V
I need start signal parameter selector Switch not keypad
Have you checked out other 2 videos for this drive?
Sir alarm is not reset f0001
Do you want to show us or just mumble and rush through mumbling like you are tired but you will do us a favour and ramble on . Poor presentation!
Thank you for your kind comment.
please speak slowly
What is the parameters if I want to increase the speed while the motor is running. Now, I cant increase the speed P1082 because the motor is running. I need to stop the motor to change the P1082.