How To Replace Wiper Regulator 2007-17 Ford Expedition

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/24/bv...
The windshield wiper regulator drives your wipers either directly, or through a linkage, and like any other electric motor, may stop working over time. Watch this video to see how to install a new wiper regulator on your 2007-17 Ford Expedition.
• Check here for more videos on the 2007-17 Ford Expedition: • Ford Expedition 3rd Ge...
This process should be similar on the following vehicles:
2007 Ford Expedition
2008 Ford Expedition
2009 Ford Expedition
2010 Ford Expedition
2011 Ford Expedition
2012 Ford Expedition
2013 Ford Expedition
2014 Ford Expedition
2015 Ford Expedition
2016 Ford Expedition
2017 Ford Expedition
Tools you will need:
• Pocket Screwdriver
• Trim Tool Set 1aau.to/oa/1AXX...
• Pick 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Ford Expedition 3rd Generation 2007-17: • Ford Expedition 3rd Ge...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*

[@richardpollock1037]

Excellent demonstration!

[@theplinkerslodge6361]

Excellent help, vid was critical. What you may not have shown is the other plastic clips to hold the cowl in place get left in the frame when you first tear the cowls off. You have to twist the plastic clips out of the frame and push them back into the cowl to replace the cowl correctly.

[@TK-ff5kc]

You don't have to undo the hood supports. Stop the wipers in raised position, open hood, unbolt wiper transmission, move as far to the drivers side as possible, close hood, then you can pull the wiper transmission out. Undoing hood struts are not necessary.

[@mauricetaplet9382]

You were a great help…Thank you Sir!👍🏽

[@kerrigan.]

i put the linkage back in after a lot of messing around to get it into place and the motor turns the opposite way. when off the wipers are up the window. Did I link up the linkage wrong when I added the motor to it? I used the gauge.

[@rrnaes]

Hey, you
You are really cool
I have benefited a lot from you
Can you provide me a service? I have a problem with the reverse sensor, where is it located and how is it repaired?

[@willienunez5280]

Do you have part number and is this a rain delay chingaso?
I need no rain delay please

[@coleyoung3681]

My wiper arms don't seem to be in the right position. Been struggling after replacing all of this but the wipers don't seem to sit in it's "home" position when I turn them off. They sit about 2 inches higher than they should. When I set them lower, they want to ride down and over the grill beneath it. What did I do wrong??

[@DjCBlaq]

I can't find this part under the expedition or navigator on the site.

[@brothercheerio]

How did you hold up the hood after you disconnect it?

[@Schtuperfly]

What's a wiper REGULATOR regulate? What did the car do wrong that indicated it needed replacement or did it just offend you in some way?