Great guide - one thing that you skipped over (probably because you knew how to do it already) but selecting the Band on the Black Pearl is a bit tricky and I read the instructions and still couldn't work it out. You have to press the power button to bring up the menu and then M (or Mode) to select the submenus. This will allow you to pick the Band and also change the signal input to match your signal format (PAL/NTSC) from your GoPro.
Using the “video out” (Brown, Red & Yellow) cable that was supplied with the Phantom Upgrade board, expose the Brown (ground) & Yellow (Video) wires roughly 1.5cm in length at the bare end of the cable opposite end to connector. Bend the Red (Active) cable back out of the way and keep out of the way with electrical tape. *Refer to pic 2 *Red (Active) is not required when using the DJI 5.8gHz Av system.
Thanks for the vid--instructional and well presented. I presume that in order to get vid out, the zenmuse usb cable is plugged into the Gopro. Also I suspect that the gopro operates via it's own battery power--so a full charge before use is advisable. And that the gopro auto shutdown is off--and that the SD card is not full. Depending on the gopro's vid settings, some minimal lag might effect FPV vision. Especially if flying in amongst trees. I think that the power usage of the A/V TX unit is fairly minimal but may effect flight times. Cheers.
You should also remove the Black cable from the IMRC lead. One battery onboard means you already have a common NEG coming into the Tx, and you don't want to create Ground Loops.
Glad to see your tilt function on your remote works, mine didn't but I modified it with a knob on the front .. Hmm I can't wait to get fpv set up ... And some more batteries .. Thanks for posting the how to..
hey dbest1a if your tilt function does not work its usually the lever not making contact with the yellow star shaped pots inside, you can just lift up the green control board a little and it works, thanks for watching.
ThatHPI GUY See, I've been dreaming of this pitch movement for ages. All I've managed to figure out was how to make it "always stay" in a different position on start up! Now, I can see the lever isn't touching the yellow pot inside (it's like 2mm to 3mm off) and it dazzles why DJI would build something not to work, even tho they give you all the tools! My question here is, how to raise the green control board (if easy) or should I just buy the DJI Phantom Tilt Lever that quadcopters.co.uk have on their website? Any ideas? Thanks
Sergio Ferreira a I got annoyed with fiddling n found a video on UA-cam that showed me how to change it over to the knob.. But maybe like ThatHPI GUY says some washers under the board will raise it up a bit
dbest1a it stops working if you have not calibrated it all the right way ie the phantom first then the rc mine stopped working then i did this then it worked
Great video very straight forward and helpful. Can you help me with batteries and what that looks like on the receiver? I feel a little overwhelmed on how I should go about setting that up! Thanks for posting this!
No, not yet, I've been looking all over the net, but can't find them. Anyone else know anything about the wire strippers/cutters that he's using? Cheers from Toronto?
It looks like you have done this installation twice (2 different videos) - one with the connections for the transmitter insider the phantom and one outside? Or am I seeing things?
Excellent video, very informative. Where did you put the anti-interference board though? Would be really handy to know where it would fit on the bottom.
Totally awesome video man. I have a question, it's a off question so I do apologize, I have a extra Phantom 2 transmitter (original one from DJI) and I want to use it with my phantom 2. can you steer me in the right direction on how to program it for my phantom 2? Really do appreciate any help, thanks.
Thanks for the informative video. Only problem is, I did everything you exact to the T, with exactly the same thing you have here and it doesn't work. Screen is black. Now back to square one in determining issue. Any ideas would be greatly appreciated.
First of all congrats for such didatic video. Can you inform what type/brand of shield and heat shrink you used over the transmitter cables? Very nice finshing! Cheers.
HI Rich, and thanx for the Gr8 Tutorial. Question: When using an FPV with a GoPro, and while in flight, is it possible to View (using FPV) AND Record Video at the same time? (it's like: What you're viewing is what's being recorded)
The video feed is sent from the back of the GoPro through the HD-2D and version 1.0 of the HD-3D using the proprietary connector. On the HD-3D 1.1 the gimbal uses a USB connection. which still passes to the Phantom 2 board. The CAM connector on the mainboard of the Phantom 2 then sends the video feed to the transmitter via the cable that is soldered.
very cool and easy to understand video THX :D What is the range of this video transmitter? If I fly away to the max range with the Phantom 2 will I still get video feedback?
I was install the receiver inside the drone and was connected the extra antenne on the side from the drone it is working so well and have no receiver under the drone any more !!
Hi! great vid...u sure made it look simple. I have a query tho, for the heat shrink what size did u use? 3/32" ? 1/4" ? would help to know which size diameter to get..Thank you
Nice video! But I need your help... I follow all the steps with my Phantom 2, H3 3D gimbal, Boscam TS832 and Boscam RX-LCD5802 but all I have is a super bad quality video with too much interference like I can't have clear image. I tried all frequency and channels but nothing :( plz help me
Hello, great video. I have installed everything and it was working for about a minute or so. I believe i may have had some wires touch. So now when the DJI is on and the gopro is plugged in I receive signal on the black pearl but no video. it is just pure black. Do you have any ideal of how to fix this?
So I just followed this video exactly, and when I went to the IOSD mini update and turned on the phantom, I got a spark and a puff of smoke from the motherboard right where the yellow IOSD mini cord plugs in..... what .... the ... heck.. do I do?
What if you dont have those wires sticking out of the phantom2? What to do then? I got a working Zenmouse gimbal wired to the phantom 2 along with a gopro 3 but i dont have the 4 extra video cables sticking out to connect to a video transmitter. Also i dont have any tools to connect the wires like you do. What should i do then?
Hi there! Nice video, i have a little doubt, that video transmitter you show comes with the black pearl monitor system or is something aditional is needed , if is aditional how is it call technically? where do i find it? Thanks
This is all I need to get a live video on my controller?? Just got my dji phantom 2 and I need a monitor with the transmitter, please let me know thanks.
David, Thank you for the most excellent video. I ran into a problem after I finished the install. The install went fine everything works but now I am having trouble getting sat lock. When I first flew the P2 a week ago I was amazied how quickly it locked home position. Now it takes several minutes and at most I've seen 6-8 sats. I did unpower the vtx with no help then unpowered the GoPro with no help. I am thinking it may have something to do with the Zenmuse gimbal causing interference. Have you heard of any issues like this? Thank you for any advice, Tom
Hi, thanks for the vid. I've followed through all the way, and done everything outlined. But am still not receiving any video signal on my monitor? Any idea why this might be? Also, I noticed you have a HDMI out on your gimbal whereas I've got a USB on the side instead, would this make any odds? Thanks
Have you done an install on the Dji phantom 2 vision plus? This unit comes with the Dji video cam already installed and I want to do a good clean install. I have the black pearl monitor.
thank you for the video - i am trying to run a similar setup (gopro here 3, black pearl 7', immersionRC 5.8ghtz transmitter, patch antenna on my black pearl) BUT, i have the phantom vision 2. Will i also need to solder those cables like you did?
I have the phantom 2 with the H4-3D that came with it, would the video transmitter that you show work with my phantom? Also those 4 wires that need to be soldered, i have that on my phantom 2 as well, they are all the DJI fpv wires for the gopro? Fill me in on what i need to get for this, im looking into getting fpv for my phantom. Thanks!!!
hi can i just ask which cables are just for power as i would like to put a 3s jst plug on the power cable so i can run my after market gimbal and my light kit,
are you using an iosd mini? I have an immersion and a blackpearl monitor i am using band 7 and have the first two switches turned off.. I have tried all of the channels and still nothing what am I doing wrong?
If you buy a phantom 2 vision plus as well as a zenmuse HD-3D gimbal, can you remove the vision plus camera (and attached gimbal) and install the zenmuse gimbal for use with a gopro?
Shouldn't you also connect a suitable antenna before powering on the video transmitter? And also on the receiver? (although its less likely to damage the receiver than the transmitter)
Très belle vidéo rien à dire encore bravo pour ce superbe montage très clair et très précis moi maintenant je voudrais me lancer dans dans le drone de lui qu'est-ce mais je ne sais pas quoi trop prendre car je voudrais quand même un produit haut-de-gamme est très très performant encore bravo pour ces vidéos je recommande et continuer comme ça bravo bravo
Et je voulais dire que depuis quelques mois je suis dans drone de vitesse et je voudrais un produit plus performant avec lunettes compatible suivant l'acquisition encore bravo bravo pour ce superbe vidéo en en 250 ou 350je ne sais pas ce que ça donne si il y a des conseils à me donner je suis preneur merci à tous et à toutes et merci pour ces vidéos et j'encourage
I noticed the gimbal in this video plugs into the back of the gopro....i have like the exact same gimbal but on mine doensnt plug into the back of the gopro, mine plugs it into the USB port on the side of the gopro....so i was wondering if this would still work for mine if i plug it into the USB port??? please help!?
hi i have been following your channel your great help , im having a problem with my naza assistant every time i connect my phantom 1.1.1 to assistant my pc does not recognise the drivers i am getting a code 43 fault no matter what i do even using a different pc i get the same fault is there a problem with my naza v2 im trying to install a feiyutech gimbal on my phantom , any help would be great thanks
ive purchase a black pearl monitor, immersionRC and a set of Flysight clover leaf omnidirectional but the flysight clover leaf antenna does not fit in the Receive but fits on the Transmitter. Can i use a sma female to female adaptor or i have to buy a new set of antenna to fit in the Receiver? pls help!
I am at the same spot, I purchased the immersion rc and black pearl based on this video, yet I get poor range, it seems the black pearl is rp-sma connector and the immersion is sma, now trying to understand what antenna to buy and if a connector will fix the connection problem while still maintaining continuity for longer range. please help.
Hey, great video!! Q- I like the wire stripper your using. Can you tell me what it's called, where you got it, and do you recommend it? Thanks, I appreciate your opinion, and help. Cheers from Canada..
hi have you got an email address i can contact you on please? i have the phantom 2 vision and it came with a pre installed gimble and camera, i want to take it off and install a better camera but i dont know how to without damaging the drone. Please help!!!
One of the most helpful things, in my process of learning to set up my Fpv system with my Phantom 2. I would give it 100 thumbs up if I could.
So rare to find such clarity online :) Thanks.
Great guide - one thing that you skipped over (probably because you knew how to do it already) but selecting the Band on the Black Pearl is a bit tricky and I read the instructions and still couldn't work it out. You have to press the power button to bring up the menu and then M (or Mode) to select the submenus. This will allow you to pick the Band and also change the signal input to match your signal format (PAL/NTSC) from your GoPro.
Thanks, I didn't realize it was that simple
just picked up a solder kit online yesterday, running fpv today thanks helped a lot!
Using the “video out” (Brown, Red & Yellow) cable that was supplied with
the Phantom Upgrade board, expose the Brown (ground) & Yellow
(Video) wires roughly 1.5cm in length at the bare end of the cable
opposite end to connector. Bend the Red (Active) cable back out of the
way and keep out of the way with electrical tape. *Refer to pic 2 *Red (Active) is not required when using the DJI 5.8gHz Av system.
Just installed mine using your video as a guide. Works perfectly! Thanks you sir!
Great video! Thanks for taking the time to make it! Can't wait for my Phantom 2 to arrive. Have you been happy with your Diversity Monitor?
Thanks for the vid--instructional and well presented. I presume that in order to get vid out, the zenmuse usb cable is plugged into the Gopro. Also I suspect that the gopro operates via it's own battery power--so a full charge before use is advisable.
And that the gopro auto shutdown is off--and that the SD card is not full.
Depending on the gopro's vid settings, some minimal lag might effect FPV vision. Especially if flying in amongst trees.
I think that the power usage of the A/V TX unit is fairly minimal but may effect flight times.
Cheers.
You should also remove the Black cable from the IMRC lead. One battery onboard means you already have a common NEG coming into the Tx, and you don't want to create Ground Loops.
Glad to see your tilt function on your remote works, mine didn't but I modified it with a knob on the front .. Hmm I can't wait to get fpv set up ... And some more batteries .. Thanks for posting the how to..
hey dbest1a if your tilt function does not work its usually the lever not making contact with the yellow star shaped pots inside, you can just lift up the green control board a little and it works, thanks for watching.
ThatHPI GUY See, I've been dreaming of this pitch movement for ages. All I've managed to figure out was how to make it "always stay" in a different position on start up!
Now, I can see the lever isn't touching the yellow pot inside (it's like 2mm to 3mm off) and it dazzles why DJI would build something not to work, even tho they give you all the tools!
My question here is, how to raise the green control board (if easy) or should I just buy the DJI Phantom Tilt Lever that quadcopters.co.uk have on their website?
Any ideas?
Thanks
Sergio Ferreira a
I got annoyed with fiddling n found a video on UA-cam that showed me how to change it over to the knob.. But maybe like ThatHPI GUY says some washers under the board will raise it up a bit
dbest1a it stops working if you have not calibrated it all the right way ie the phantom first then the rc mine stopped working then i did this then it worked
RushNReady I already removed it n replaced it with a knob on the front
great video i had ordered my Phantom 2,, this would help a lot...thanks for sharing
Great video thanks! I was wondering if there is any danger in leaving the plastic wrap on the transmitter board, does it heat up ?
Thanks!
Nice job! Very very useful tutorial video.
Great video very straight forward and helpful. Can you help me with batteries and what that looks like on the receiver? I feel a little overwhelmed on how I should go about setting that up! Thanks for posting this!
ThatHPI GUY
No, not yet, I've been looking all over the net, but can't find them. Anyone else know anything about the wire strippers/cutters that he's using? Cheers from Toronto?
I found them at www.ascendtools.com/
5" & 6” Two in One Combination Electrical Wire Stripper and Cutter, 26-10 AWG
Hi, so once you have installed that, can you fly and see what the camera is recording? also, what´s that of the IOSd? Thanks
It looks like you have done this installation twice (2 different videos) - one with the connections for the transmitter insider the phantom and one outside? Or am I seeing things?
Excellent video, very informative.
Where did you put the anti-interference board though?
Would be really handy to know where it would fit on the bottom.
That was extremely helpful and informative. Thank you!!
Thank you so much !
your video was perfect ! just like the end result !
thanks !!!
Many thanks for ur video. Now I know how I have to install.
Thanks mate!!!
Very informative Video, Thankyou indeed!
Totally awesome video man. I have a question, it's a off question so I do apologize, I have a extra Phantom 2 transmitter (original one from DJI) and I want to use it with my phantom 2. can you steer me in the right direction on how to program it for my phantom 2? Really do appreciate any help, thanks.
Thanks a million. Your advice helped. Thanks again
Wow that seemed pretty simple, so the mini iosd that I keep seeing everyone install really isn't necessary right?
Great video
Great video.
Thankyou for this Video!
Thanks for the informative video. Only problem is, I did everything you exact to the T, with exactly the same thing you have here and it doesn't work. Screen is black. Now back to square one in determining issue.
Any ideas would be greatly appreciated.
God bless you
Quick question, do you know if there are any changes to the install with the Zenmuse H3-3D gimbal over the H3-2D?
Thank you so much! This was so helpful!
Hey,
where did you get the parts you show at 6:23 ?
They are not included in my Zenmuse Gimbal :/
Nice Video ^^
hey DjIch1 they come with the phantom2 gimbal
Great job on your video. Can you recommend a good reputable vender- for the Black Pearl and other multicopter parts? Thanks!
First of all congrats for such didatic video. Can you inform what type/brand of shield and heat shrink you used over the transmitter cables? Very nice finshing! Cheers.
Supremus Absolutus Hello, Very nice job.!!Did you got the type and brand of the cable shield used?
Thank u!!
Thanks for this informative video, you made it look very straightforward. What is your typical range with this set up? Thanks :)
Wow nice introduction movie of installation. question: what transmitter are you using exactly?? thanks!!
HI Rich, and thanx for the Gr8 Tutorial.
Question: When using an FPV with a GoPro, and while in flight, is it possible to View (using FPV) AND Record Video at the same time? (it's like: What you're viewing is what's being recorded)
Good clear video, as always. One question though, how is the final link to the Gopro made for the picture. Did I miss that ? Thanks
The video feed is sent from the back of the GoPro through the HD-2D and version 1.0 of the HD-3D using the proprietary connector. On the HD-3D 1.1 the gimbal uses a USB connection. which still passes to the Phantom 2 board. The CAM connector on the mainboard of the Phantom 2 then sends the video feed to the transmitter via the cable that is soldered.
Thank you for the info. I did it and it looks great! Do you know how to fpv while you are doing pictures with your Go Pro instead video? Thank you
First, that's an awesome video, thanks for it!
Second, did you know if it works with the GoPro Hero 4 Black edition?
at 1:45, you run the wires into what looks like a split loom. What's the diameter on the one you use? Thanks very much!
Hey great video and I like your setup just one question what is its max distance
very cool and easy to understand video THX :D What is the range of this video transmitter? If I fly away to the max range with the Phantom 2 will I still get video feedback?
Nice install:)
Hi, did you have any issues using the 32 channel Black Pearl with the 600mw transmitter, as I've read a lot of people do?
I was install the receiver inside the drone and was connected the extra antenne on the side from the drone it is working so well and have no receiver under the drone any more !!
Hey, one question, can you possibly use a different FPV monitor other than the Black Pearl?
Hi! great vid...u sure made it look simple.
I have a query tho, for the heat shrink what size did u use? 3/32" ? 1/4" ?
would help to know which size diameter to get..Thank you
Nice video! But I need your help... I follow all the steps with my Phantom 2, H3 3D gimbal, Boscam TS832 and Boscam RX-LCD5802 but all I have is a super bad quality video with too much interference like I can't have clear image. I tried all frequency and channels but nothing :( plz help me
Hello, great video. I have installed everything and it was working for about a minute or so. I believe i may have had some wires touch. So now when the DJI is on and the gopro is plugged in I receive signal on the black pearl but no video. it is just pure black. Do you have any ideal of how to fix this?
So I just followed this video exactly, and when I went to the IOSD mini update and turned on the phantom, I got a spark and a puff of smoke from the motherboard right where the yellow IOSD mini cord plugs in..... what .... the ... heck.. do I do?
What if you dont have those wires sticking out of the phantom2? What to do then? I got a working Zenmouse gimbal wired to the phantom 2 along with a gopro 3 but i dont have the 4 extra video cables sticking out to connect to a video transmitter. Also i dont have any tools to connect the wires like you do. What should i do then?
Does it matter which black wires are connected to the brown wires? Or can either black be connected to either brown?
Hi there! Nice video, i have a little doubt, that video transmitter you show comes with the black pearl monitor system or is something aditional is needed , if is aditional how is it call technically? where do i find it? Thanks
This is all I need to get a live video on my controller?? Just got my dji phantom 2 and I need a monitor with the transmitter, please let me know thanks.
David,
Thank you for the most excellent video.
I ran into a problem after I finished the install. The install went fine everything works but now I am having trouble getting sat lock. When I first flew the P2 a week ago I was amazied how quickly it locked home position. Now it takes several minutes and at most I've seen 6-8 sats. I did unpower the vtx with no help then unpowered the GoPro with no help. I am thinking it may have something to do with the Zenmuse
gimbal causing interference. Have you heard of any issues like this?
Thank you for any advice,
Tom
I want to learn to fly one of these guys, what do you recommend Tom?
thank you!
Hi just installed my transmitter using this brill video. thanks,
Can you give me link for the tape you use for transmitter
Thanks
Can this also been done with the phantom 1?
btw love your video!!
How do you feed the Zenmuse? Im not able to see any cable. Sorry i'm noobie in this amazing world.
excellent video. I have a question: how is the connection between gopro and pantom? because I do not see any wire
The H3-3D gimbal has the GoPro proprietary connector block on the rear plate. The GoPro connects there.
Hi, thanks for the vid. I've followed through all the way, and done everything outlined. But am still not receiving any video signal on my monitor? Any idea why this might be? Also, I noticed you have a HDMI out on your gimbal whereas I've got a USB on the side instead, would this make any odds? Thanks
Did you use the basic remote controls that comes with the Phantom 2 or is this an upgrade .
thanks man!
Have you done an install on the Dji phantom 2 vision plus? This unit comes with the Dji video cam already installed and I want to do a good clean install. I have the black pearl monitor.
Would you recommend the ImmersionRC 600mW transmitter for a first time FPV user? Also what kind of range do you get with it? :) Thanks!
I like your tools! Where can I buy wire stripper and cutters like the ones you use?
try CPC.co.uk
Is this the standard phnatom 2, or is the vision or vision plus?, ?
hi, the question is, if i do it, will the video also go to my phone laptop as usually? or it either way?
thank you for the video - i am trying to run a similar setup (gopro here 3, black pearl 7', immersionRC 5.8ghtz transmitter, patch antenna on my black pearl) BUT, i have the phantom vision 2. Will i also need to solder those cables like you did?
How long range does the transmitor have? Please answer.
I have the phantom 2 with the H4-3D that came with it, would the video transmitter that you show work with my phantom? Also those 4 wires that need to be soldered, i have that on my phantom 2 as well, they are all the DJI fpv wires for the gopro? Fill me in on what i need to get for this, im looking into getting fpv for my phantom. Thanks!!!
hi can i just ask which cables are just for power as i would like to put a 3s jst plug on the power cable so i can run my after market gimbal and my light kit,
are you using an iosd mini? I have an immersion and a blackpearl monitor i am using band 7 and have the first two switches turned off.. I have tried all of the channels and still nothing what am I doing wrong?
If you buy a phantom 2 vision plus as well as a zenmuse HD-3D gimbal, can you remove the vision plus camera (and attached gimbal) and install the zenmuse gimbal for use with a gopro?
Shouldn't you also connect a suitable antenna before powering on the video transmitter? And also on the receiver? (although its less likely to damage the receiver than the transmitter)
YES always on the video transmitter, its not important on the receiver, I do say this in the video.
Is there an led installed on that particular Transmitter?
Très belle vidéo rien à dire encore bravo pour ce superbe montage très clair et très précis moi maintenant je voudrais me lancer dans dans le drone de lui qu'est-ce mais je ne sais pas quoi trop prendre car je voudrais quand même un produit haut-de-gamme est très très performant encore bravo pour ces vidéos je recommande et continuer comme ça bravo bravo
Et je voulais dire que depuis quelques mois je suis dans drone de vitesse et je voudrais un produit plus performant avec lunettes compatible suivant l'acquisition encore bravo bravo pour ce superbe vidéo en en 250 ou 350je ne sais pas ce que ça donne si il y a des conseils à me donner je suis preneur merci à tous et à toutes et merci pour ces vidéos et j'encourage
good tutorial! this method serves to transmitter boscam ts352? thank you
is it possible to use our smartphones to receive the signal emitted by the video transmitter ?
I noticed the gimbal in this video plugs into the back of the gopro....i have like the exact same gimbal but on mine doensnt plug into the back of the gopro, mine plugs it into the USB port on the side of the gopro....so i was wondering if this would still work for mine if i plug it into the USB port??? please help!?
so will this fpv system still work with my updated senmuse gimbal?
Where i can find a fpv transmitter like this but not expansive ? :)
Sorry i am french 😅
hi i have been following your channel your great help , im having a problem with my naza assistant every time i connect my phantom 1.1.1 to assistant my pc does not recognise the drivers i am getting a code 43 fault no matter what i do even using a different pc i get the same fault is there a problem with my naza v2 im trying to install a feiyutech gimbal on my phantom , any help would be great thanks
Is that better with the IOSD MINI or without like in your video for the FPV ?
Hi, Did you selec band f on monitor, before channel. Also will it select the correct channel ie 1,2,3 etc? Thanks...
Bien fait - Merci
Awesome
but can your gopro still record while you use the fpv?
ive purchase a black pearl monitor, immersionRC and a set of Flysight clover leaf omnidirectional but the flysight clover leaf antenna does not fit in the Receive but fits on the Transmitter. Can i use a sma female to female adaptor or i have to buy a new set of antenna to fit in the Receiver? pls help!
I am at the same spot, I purchased the immersion rc and black pearl based on this video, yet I get poor range, it seems the black pearl is rp-sma connector and the immersion is sma, now trying to understand what antenna to buy and if a connector will fix the connection problem while still maintaining continuity for longer range. please help.
I lost my gopro is there another camera I can use?
Cables comes with the reciever?
Hey, great video!! Q- I like the wire stripper your using. Can you tell me what it's called, where you got it, and do you recommend it? Thanks, I appreciate your opinion, and help. Cheers from Canada..
Did you get the answer? I also like the wire stripper too. :)
I found them at @t
5" & 6” Two in One Combination Electrical Wire Stripper and Cutter, 26-10 AWG
www.ascendtools.com/
where I can buy and same transmitter you use it?
Thank You
So can you record footage with the gopro while in FPV? please get back to me
Yes you can, it live feeds from the hdmi out and records at the same time
What distance can you reach with this configuration?
May I know how far is the transmission?
Where do you get your wire stripper from?
what was the diameter of the sleeving?
Hey "ThatHPI GUY" i was just wondering what tool you were using to strip the wires and cut them. i need that tool but i cant find it anywhere thanks!
Vpanzer
tigre
sebastien tellier thanks for your response, but Google only shows me info on tanks :P Are you sure about the name? Do you have a link maybe?
hi have you got an email address i can contact you on please?
i have the phantom 2 vision and it came with a pre installed gimble and camera, i want to take it off and install a better camera but i dont know how to without damaging the drone.
Please help!!!