I just purchased a Jura Z10 Signature for half price while on vacation in Germany, image my dismay when I couldn't even get past the startup menu after spending 3 hours running a 240V wire to my kitchen counter. "Drip Tray Not Fitted" message. Rather than chase a complicated shipping & warranty repair I decided to take a look inside ... with your video I had Z10 stripped naked in less than 5 minutes. Found the problem right away, one of the door micro switches (see orange wires front bottom) had popped loose in shipping, snapped it back down (no tools) and the message went away. Finished the setup menu and my Z10 works perfectly. Your video gave me the confidence to lift the hood and find the problem. Thank you very much! Vielen Dank
Well one month later and the same message "Drip Tray Not Fitted" returned. Had the side panel open in 2 minutes as I never put back the 2 oval tamper resistant screws. Yup, same inboard micro -witch was popped up again. Upon closer investigation found 2 tiny plastic pieces in the bottom of the unit, these are retainer clips that are meant to hold the micro-switches in place. They must have broke off during shipment, no doubt from an impact drop. Sure enough the shipping box bears the mark on the front right corner. Clever solution ... foam earplugs, rolled them up and placed one above each micro-switch, foam expands and holds the switches solidly in place.
Did they update the design and hose size? I have had a number of giga 10s which keep getting a system fill error message. I am using grind setting fine or medium. Fine seems to always cause error message.
You should check the membrane thing. This is a part after the water pump. The membrane is a one way valve, to check the parts you need to blow from output to input, if the wind comes out from the output to input, your membrane is need to replace.
I just purchased a Jura Z10 Signature for half price while on vacation in Germany, image my dismay when I couldn't even get past the startup menu after spending 3 hours running a 240V wire to my kitchen counter. "Drip Tray Not Fitted" message. Rather than chase a complicated shipping & warranty repair I decided to take a look inside ... with your video I had Z10 stripped naked in less than 5 minutes. Found the problem right away, one of the door micro switches (see orange wires front bottom) had popped loose in shipping, snapped it back down (no tools) and the message went away. Finished the setup menu and my Z10 works perfectly. Your video gave me the confidence to lift the hood and find the problem. Thank you very much! Vielen Dank
Well one month later and the same message "Drip Tray Not Fitted" returned. Had the side panel open in 2 minutes as I never put back the 2 oval tamper resistant screws. Yup, same inboard micro -witch was popped up again. Upon closer investigation found 2 tiny plastic pieces in the bottom of the unit, these are retainer clips that are meant to hold the micro-switches in place. They must have broke off during shipment, no doubt from an impact drop. Sure enough the shipping box bears the mark on the front right corner. Clever solution ... foam earplugs, rolled them up and placed one above each micro-switch, foam expands and holds the switches solidly in place.
Beautiful Z1O! I'm looking forward to the next black friday to offer it to me.
great work! is that a torx screwdriver to remove the panels? thanks!
Yes. And special tools called oval bit.
Ok thanks so much. Someday I’ll want to open my beautiful new z10.
Where can i buy the screwdriver for those 6 divot screws?
Jura - parts . Com
Hi
What part did you use
I replaced membrane, it is one way valve that connected on the water pump.
Thats what I call an expensive crap.
Wow, your method of doing absolutely nothing was no help.
Did they update the design and hose size? I have had a number of giga 10s which keep getting a system fill error message. I am using grind setting fine or medium. Fine seems to always cause error message.
You should check the membrane thing. This is a part after the water pump. The membrane is a one way valve, to check the parts you need to blow from output to input, if the wind comes out from the output to input, your membrane is need to replace.