Honeycomb Configurator - How to use Datarefs and Commands
Вставка
- Опубліковано 8 вер 2024
- This video will show you how to use X-Plane 11 Datarefs and Commands inside the Honeycomb Configurator.
X-Plane Datarefs
www.siminnovat...
X-Plane Commands
www.siminnovat...
Mr Jara, thanks for all the videos. Looking forward to a whole bunch more (especially P3D pay ware A/C videos!) I know it’s a lot of work and I just wanted to say thanks for doing it!
This effort is above and beyond, vielen dank! Wish we could buy you some beers.
Thank you for a very informative tutorial.
Is FCU_SELECTOR a variable defined in the Bravo firmware, or is it an arbitrary name you assign?
I'm having a problem in X-Plane where it does not seem to recognize this variable, or it says the associated value is not writable. Any help appreciated.
Great tutorial ... thanks for what you are doing. I wanted to ask how to do for the C172 in the Laminar X-Plane 11 S-TEC 55 to set, in the NAV button, the possibility of push the NAV button TWICE to select GPS Steering (GPSS) mode. Thanks.
with the next version, it would be possible. In the next version, you are able to make press events as many as you wish. So you could make also a press event with a local variable like in the FCU selector to track the amount of pushes and then you can capture it with a condition in another press event.
on your video above you show the autopilot switches (HDG,NAV...IAS) backlit when not in active use. then when you select, say HDG, the light intensity increases to indicate it's in use. I use x-plane and none of these buttons are backlit. They do light up when depressed for use. Can you show me an example of the condition that I could apply to each of these lights to have them backlit when not in use. Thanks Roy
Hi. Thanks for the video. How do you get a downloaded profile from the aerosoft website into the joystick profiles in xplane? I downloaded one for A319 but i do not know how to upload into my sim so i can use the profile. Any help will be appreciated.
Thank you.
Thanks for your videos. Using a FlightFactor Airbus and having difficult time figuring a way to enter a command like "a320/Panel/FCU_Vertical_switch" in the configurator . Under condition it does not show the datarefs/commands for this aircraft. When I try to use CUSTOM_NAME and enter the event when I load XPLANE it complains that this event will be discarded because of a null value. Any way to do this?
Can you tell me is there a way to use non-default commands with this? I am trying to configure the autopilot panel with the Flight Factor 757, which uses it's own commands in a separate folder.
Bei fast allen LED's oder Switches habe ich ein geeignetes Command oder Datatref für X-Plane gefunden. Jedoch bei der FCU-VS LED bin ich ratlos. Welche Dataref könnte Auskunft geben, dass der AP nach VS steuert? Bitte um Unterstützung!
Ich würde mir generell mehr Customer Support von Honeycomb/Aerosoft wünschen. Und auch mehr fertige Profile für verschiedenen Flugzeuge, zumindest für die im Lieferumfang von X-Plane 11/12 oder MSFS2020 enthaltene Flugzeuge wär schon echt super. Das Herumprogrammieren von ist cool für NERD's aber nicht zwangsläufig für Leute, die Fliegen statt programmieren wollen.
how can i make this work for the SSG 747-8. I'm pretty knew to this dataref stuff
I wish I saw this video before I ordered my bravo I would of stayed with my logitech stuff. Dont these guys know people work for a living and dont have time to program for hours just to get advertised features to work? WTF
Thank you for this video! Did you ever figure out how to eliminate the red hydraulics light on the panel for the Cessna 172? Also, for the Cessna 172, is there anyway to increase the sensitivity of the trim wheel? In its default configuration, you have to turn it way too many times to get any appreciable response.
Yes within the latest version of the config tool (released since 5 minutes). Just check out the aerosoft forum and then you can use the new repeat function (Off, Normal, Delayed Normal, Delayed Fast)
Hey @lalawyer11, did you ever get around correcting the sensitivity of the trim wheel?
Hi Mr Jara
Thank you very much for this very good tutorial. Thanks to you my Honeycomb Bravo is operational. Without you video it was impossible for me. I have a little problem with the CRS to Increase or Decrease the axis to intercept and follow a VOR. I do not find the variable. The name is as requested INT:FCU_SELECTOR, string and value CRS but in the X plane variable list (command) I do not find somethng like course_down and course_up. I try sim/GPS/g1000n1_crs_up and down. But nothing happen
So the please could you help me to indicate the good variable. All other functions are working perfectly well.
I fly with the embraer 135 : one of my former aircrafts. I am retired now
PS :By hearing you, your english isvery good. I am a French and I prefer to hear you than an English. It is very difficult with an english accent except for a technical aeronautical conversation LOL
HI Mr JaraI have found the variable this morning sim/radios/obs1_up or down. I would like now to offer my XXX.json to the other pilots for the X CRAFT EMBRAER FAMILY. My honeycomb A and B are fully working now. Have you the solution to offer the download .json I would like pilots flying with EMB 135...145 to use my work.
Is there anyway to configure Autopilot for the Flight Factor A320/A350 in Xplane 11 with Bravo?
you can take a look into the aerosoft forum if there is already a profile for that airplane
forum.aerosoft.com/index.php?/files/category/126-honeycomb-profiles/
@@MrJaraNet I could not find any..
complicated to configure in X-plane :-o
Great video, but the mumbling was a little annoying :)
Dude you need to make presets, this could have been a great product...you ruined it. It's terrible, gonna return
Why did u make this soooooo confusing bro!!???