If build a transfer case, i would want to add gears to it, besides 2&4wd, hi & lo, a 🐢 ultra low gear. + Low gear, medium, 1:1, then a 10% , 20%, 35% 50% over drive ratios, along with a 2wd only, 4wd only, a separate shifter for 2&4wd. Basically a 5-speed transmission bolted in a 5speed transmission,with a few extra gears added. then the 1 transmissions gears can be split. 1st gear, +low,med ,high, 2nd,+low ,med,hi , 3rd +L. ,M. Hi 4th, +L,M,Hi., 5th+ L,M,Hi. Then the other 5gear, 15 gears + another overdrive gear!😮 It would be like a semi truck. Only more like a 1/4ton truck over loaded and under powered! Allowing a 10hp Diesel engine to carry the truck loaded, it may run like a Hurd of turtles, but it would climb a tree, if it had traction.. i do want to build a tractor, 4x4, micro tractor , with 33"x12.5" tires , and debating on the engine, either a 5-10 hp mower style engine or a car engine. From 2.2 litre 4cyl, to 4.0L v6. Or electric using forklift motor, 10-12 kw. x 2, one can be used as the PTO, or shifted to power the tractor. Id build it with 4wheel steering with a short wheel base. Not much more than 24" between tires , and 44" tires may be added later, use two rear diffs from a mustanf or dodge , with the same ratio, put a 34tooth sprocket on the input, drive it with a 11 tooth, along with a 5-speed use s 1.5" shaft to drive both, with a pair of 12 tooth speockets on the shaft one on the transmission out shaft. To keep 1:1, but have other available. A 2:1 over drive, a 1:2 underdrive. To make good power and slow speed the final drive should equal 6.50:1-7.00:1 plus 1st gear, it should have thr TQ to spin the earth. At 1 mile per year. And run another shaft from the transmission input shaft, probably a chain drive or belt drive. With another independent drive with a 2:1 reduction and the transmission gets a 50 lb flywheel a 4" channel iron frame, with a 2" tube bracing and cab, with 1" tubing and 2" angle , with a 60' wide 16" scrape blade with 24" travel , also a. 16x60 bucket with a dump function. The lift by winch. The dump, possibly linear actuator. Maybe hydraulics eventually. Possibly powered by 2, old school 5hp engines or scale the whole thing up 10% and use a car engine. Have a awesome day...
Vip qua ido oi
Thanh kiu
Ficou muito bom parabéns aqui é BRASIL
Thank you very much
0:19 ⭐️⭐️⭐️
🥰thank you
Good job💪
Thanks Bro
Nice👏👏
Good 👍👍
Thank you
Привет! Молодцы! 🤝👍👍👍👍👍 у нас мороз , -24 ! 😢 ни чего не дает делать!
❤❤❤❤
If build a transfer case, i would want to add gears to it, besides 2&4wd, hi & lo, a 🐢 ultra low gear. + Low gear, medium, 1:1, then a 10% , 20%, 35% 50% over drive ratios, along with a 2wd only, 4wd only, a separate shifter for 2&4wd. Basically a 5-speed transmission bolted in a 5speed transmission,with a few extra gears added. then the 1 transmissions gears can be split. 1st gear, +low,med ,high, 2nd,+low ,med,hi , 3rd +L. ,M. Hi 4th, +L,M,Hi., 5th+ L,M,Hi. Then the other 5gear, 15 gears + another overdrive gear!😮 It would be like a semi truck. Only more like a 1/4ton truck over loaded and under powered! Allowing a 10hp Diesel engine to carry the truck loaded, it may run like a Hurd of turtles, but it would climb a tree, if it had traction.. i do want to build a tractor, 4x4, micro tractor , with 33"x12.5" tires , and debating on the engine, either a 5-10 hp mower style engine or a car engine. From 2.2 litre 4cyl, to 4.0L v6. Or electric using forklift motor, 10-12 kw. x 2, one can be used as the PTO, or shifted to power the tractor. Id build it with 4wheel steering with a short wheel base. Not much more than 24" between tires , and 44" tires may be added later, use two rear diffs from a mustanf or dodge , with the same ratio, put a 34tooth sprocket on the input, drive it with a 11 tooth, along with a 5-speed use s 1.5" shaft to drive both, with a pair of 12 tooth speockets on the shaft one on the transmission out shaft. To keep 1:1, but have other available. A 2:1 over drive, a 1:2 underdrive. To make good power and slow speed the final drive should equal 6.50:1-7.00:1 plus 1st gear, it should have thr TQ to spin the earth. At 1 mile per year. And run another shaft from the transmission input shaft, probably a chain drive or belt drive. With another independent drive with a 2:1 reduction and the transmission gets a 50 lb flywheel a 4" channel iron frame, with a 2" tube bracing and cab, with 1" tubing and 2" angle , with a 60' wide 16" scrape blade with 24" travel , also a. 16x60 bucket with a dump function. The lift by winch. The dump, possibly linear actuator. Maybe hydraulics eventually. Possibly powered by 2, old school 5hp engines or scale the whole thing up 10% and use a car engine. Have a awesome day...
The next road tes
Thank you for watching the video
Если это реверс.редуктор, то можно сделать из трёх конических шестерен.
❤❤❤❤❤❤❤
Luar biasa
❤
⭐️⭐️⭐️
VERRY GOOD please video how made front exel gardan
i am from indonesia
In my channel
@@2TDIY oke thank you sou much
Nice
Ini lagi Di rantau bossqu, bila dh balik nnti, dua set aku pesan, Sgt rasio bosss
Thank you very much
ntastik
Giá sao vậy a
1tr a
Nice👏👏
Thank you