Moronic how the govts of certain countries see these as Firearms .In the 70s we have 20 ft lb air rifles .The one and only reason the 12 ftlb rule came in was to protect the British air rifle makers as they could not compete with the HW german make. Treating adults like kids is moronic
Most of the laws are idiotic and they say it’s to prevent crime lol people committing crime don’t care about the law anyway so just let us have some freedom
Just for balance of course… Many years ago a friend of mine, whilst putting an Ox in his Hw35 got the breech block cross threaded. He brought it over so we could mount it in my jig and hopefully resurrect the situation. Well..couldn’t get it out so I held the breech tight with a leather gauntlet, while he twisted. Some you guys will know that the HW spring carrier is roughly cut and splayed out in a cross shape - remember the roughly cut bit, it’s important. Yep..we twisted..something thudded onto my thumb and the spring went airborne. The first sign of trouble was that there didn’t seem to be a proper thumb in the thumb of the gauntlet any more. There was a neat “v” shaped cut in the leather where my thumb should have been. The spring carrier went through the leather, hit the top of the base of my thumb, went through down to the bone and dislocated it so it was laying next to my wrist. One surgery and plenty of ribbing later, all was good. Still got my Venom arms HW 77k, must be 35years old and I’d still rather hunt with it than use my pre charged rifles.
Make two short pins the size of the trigger group so that you can push out the long pins and leave the two short ones in place to keep the trigger group all in line and it makes assembly a doddle as everything is held in place and the safety simply slides in again no problems I made mine from brass rod and they are a godsend for servicing the rifle. The video is great and the results are very good you are doing a great job. And Nice to see someone actually doing things the safe way. Keep on keeping on stay safe from the UK.
I have a cheap B2 Chinese. 22 air rifle that the spring got weak after couple of years. So bought a vortek spring for the rifle same length as the old one played hell getting the new one in. And cocking was hard also. So I cut the new spring down a couple of coils and flatten and polish the end. That rifle shoots 10 time better then when I first bought new awesome now. I even got one of their moly seal for that rifle even better. Vortek Inc. make great products for your air rifles American made from Michigan. More fps dose not mean better accuracy that's what you want accuracy with the right fps. And the right pellets also. Good luck bud.
I took an HW 80 up to 24 ft-lbs then dropped it back to 18 ft-lbs if it's done right you get very little recoil. At 24 ft-lbs the group size at 35 yards was around 10 inches at 18 ft lbs the group size was < 3/4 inch
I recently put a Vortek PG4 kit in my TX200 HC. I couldn't compress the new spring in by hand so I used the help of a ratchet tie-down strap, worked great!
@@BROTUNED Well, like you I'm a rim fire guy first. I'm still getting the hang of these rifles and want to see if I can outshoot my CZ LR at 50 yards. Now there's a video!!
Hi, I am about ready to change my spring - but I don't have a spring compressor or the means to make the version you use (I saw your video on how to make it and it is very good, it's just not something I can make at the moment). Is there a way to do this without a compressor? Ie by putting pressure yourself on the spring using the flat head of a file etc? I know it won't be as easy or as safe, but is there a way? Thanks!
Hi - this was such a useful video - thank you. I just have a few questions if you don't mind - a) what's the name of that flat-lying vice-like thing with the screw adjuster clamped to the end? (The thing you put the barrel in to work on)? B) I see you ordered the spring cut to 34 coils, but you said you realised you had to cut a couple more off. How were you able to tell that, and to know how much to cut off? (I ask so that I'll know when i do the same thing) C) you mention something about "locking" the screws at the end- do you mean using "thread lock" liquid? D) I'm going to order from the website you linked, specifying at 34 coils - the 142 Wire Spring 830OD. Will this spring fit most springer makes and models, or only certain ones? I have a variety of springers so would be good to know if it could work with any of them. Cheers!
A) is a spring compressor I came up with to work on springers. I made a video on making it. B)the reason I had to cut it was because it ended up binding up so I had to shorten it to allow the spring to compress. I cut a bit then tested it until the main spring compressed without any binding. Takes some time unless you make big incremental cuts C) blue locktite is a good idea on anything that moves or vibrates
this was one of the most enjoyable vids i have watched on tweaking air rifles , and has helped me gain a little more confidence to have a go on my own rifle as and when i need to GREAT JOB thanks for taking the time to share this , stay good from uk .
I have a Air Hawk Elite one pump pellet rifle the ball that rode on the barrel that helped cock it came off in the spring came out but the ball fell down in the barrel
@@brodylockley3141 The spring rotates when compresses and uncompressed so a rough finish after flattening hinders the rotation. The smoother the whole firing cycle will increase accuracy
Just to let you know, your spring end is not finished correctly , you should heat it up with a blow lamp then when it gets red pinche the top coil so its inline with the coil unneath it pointed nose pliers then let it cool down naturally before placing it back into the action.
Bullshit. You have to temper this end of spring after inline coil modification. Otherwise this end of spring is soft. Ofcourse you have to smooth the ends of spring on both side for mirror surface. This method prevent vibrations, make shooting softer, and reduces gun kicking.
@Hieronim Gąbka Big Bull Shit you are stating, you collapse the spring with heat then pinch it to the coil underneath it , you let the spring cool down naturally no need at all for water or oils. It appears you know nothing about Springer Bull Shiter .
15 years ago or so I replaced my spring in the Quest B19 with a Air Rifle Headquarters Tarantula spring that dieseled and broke. I since replaced with Air Rifle Headquarters E3650 spaced with a washer along with their Apex seal they sell. 900fps
What brand of pellet rifle is that dude ? Never seen one exactly like it. Great work on that spring compressor. That comes in handy for sure. Great work thanks for the video dude.
@@BROTUNED I believe many countries did it but the ones I found mainly Indonesians. This guy demonstrates how the muzzle flash would look like if a nail gun powder load (purple code = strong charge) was placed into the drilled BSA barrel (Indonesian limit is 4.5mm, powder loads is 5.5mm, rim 6.5mm) ua-cam.com/video/QAL3YRPdZyI/v-deo.html
@@BROTUNED Here's another one, this guy shows how he loads the powder load and uses modified piston as firing pin. The making process can be found in his channel. ua-cam.com/video/qw8FOIZAK7Y/v-deo.html
Hi mate- from the catalogue you link, there is a "148 Wire Spring 905 OD". I've figured out this means Outer Diameter is 0.905 inches = 22.5mm. What I don't understand is the "148". Is this the strength/ thickness of the wire itself? If so, is 148 a good standard to stick to? Cheers!
Please take care if you don't have a Chrono or an FAC as if you get caught with a gun over 12 ft lbs the punishment is 5 years in prison no excuses not knowing the power is no excuse
Give me 12 foot pounds air guns over submachine guns anyday. The guns ordinary people can buy in America are just pure insanity.. life is so cheap in America. So sad
@@colly7912 well sub machine guns are illegal in America so brush up. Handgun, shotguns, rifles, even the big bad ar-15 (which is NOT a machine gun) ALL require a background check and a CLEAN record. Bad people do bad things whether they have a gun or a butter knife.
Just found your vid timely. Opened up my Benjamin Classic 22 to see what is up. Chrono showing 426. Not much preload in the spring as I put a little pressure on cylinder the main support pin fell out... Gets better, Piston needed to be forced out using a probe to slide out of sleeve. Found scrubbing on the piston and ID of sleeve. Seal had metal filings embedded in it. Got pics to prove it. Removed spring and found one end squared of and reasonable smooth, However the other end appeared to be hacked off with bolt cutters and not squared or cleaned up. On the end of piston, seal end, there is a small hole drilled through not centered, not done obviously on a lathe...Metal chips.... Got some work to do but need, to replace the seal and spring for sure after I calculate an appropriate length. Then lotsa polishing and lube. If this is how they "detune" for CA Market am not impressed. Bought this brand new and wasn't cheap at that time. Wish me luck cuz, skill is no problem here. Am not on the Quest for more FPS, just what I paid for. Just subbed and liked.
Ya I think they just detune them as fast as possible to get more out. You will have a great springer if you do all that for sure. Let me know how it turns out. Remember it magically turns into a firearm after 500 fps so a pal is required. Not sure if you have one but be mindful of that. Cheers buddy and good luck!
Nice enjoin hebackground. What style o yu play? Frailing, traitionalor Earl Scruggs picking? I'm a bluegrass and d time rythm and flatpicking guitarist myself. I have a Hatsan model 85 .22 open sights which I'm really enjoying. 850fps.
Excuse me, what was the original fps of the air rifle? was it 500 fps ! But after changing the spring with thicker one, you gained more than 380 fps? so 500 fps air rifle became 880 fps air rifle now? Could you please let us know also after long term use what happaned? any problem so far?
They have springs like this with different sizes and very strong at most hardware stores that’s equipped with a good stock of things like springs to bearings.
I've read about the Ox Accelerator mainspring are square section and thus provides 40% more compression and power. If you're familiar with misumi spring you'll know square are better than regular round section coil.
@@BROTUNED been down that road years ago there is only a certain amount of volume for air in an airgun and using a heavy spring creates piston slam and harsh recoil not to mention the strain on everything cocking arm, contact points and trigger sear. If you make another video maybe explain that to the views, I am afraid people new to airguns, may destroy a perfectly good airgun
@@jimstewart5008 I found out by accident on my HW80, many years ago, just adding a small weight inside the front of the piston & then cutting off four coils from the spring, that put the power up & made it more comfortable to shoot. The trouble was, it took it over our 12ft/lbs limit so I put a standard spring back in & brought it back to how it was. It was a good experiment though.
I did do longer and got spring bind. So thicker was basically the only way but it lost its nice shootability. It’s back destined again so it shoots nice soft and accurate again
@@BROTUNED so if ı use longer spring, it will not increase the power? ı wanna buy longer spring so thats why asking ur longer spring resuts? lets say original sprign is 20 cm, but if ı use 23 cm same stiffer spring. will it increase the velocity because it has longer spring?
Yes basically that’s correct ✅ but don’t go overboard on thickness because you’ll get coil bind and make cocking it way harder for not much return in velocity. I found the gun shot best at around 600 fps
Can u tell me the exact measurements on the spring if u know them please could only see the diameter on the sheet I can’t buy from vortek in my country 😢
Anything over 12 foot pounds makes the gun less accurate simple law of physics proven . Doesn't matter what make of gun more important is gun weight but the laws of gravity × physics is finite. The point the pellet is less than a quarter of the way down the barrel at 800 fps that's fact that's life . Good video.
I had a crossman phantom . 22 500fps pellet gun from Walmart 99cad. I ordered a spring from vortek air springs... Brought it up to 1200 fps lol couldn't even keep a scope on it without a stop... Fuck it had some power... The spring was 12 bucks and like 30 to ship it to Canada lol well worth it
Thanks. Always bothered that can't get ones higher then 500 fps here in canada like at Candian Tire and just bought one and want to get it closer to 1000, so will definitely try this :)
@@colbtron OK thanks. Checked out their site and seen like 15 listed but wasn't sure which one(s) would be compatible. Will definitely do that, thanks :)
Wasn’t much but the more I go faster the more I want to put the light spring back in for quietness and light recoil. But I think it was in the 100fps range
Found an older one than this in my dad's stuff.....he died a few years ago. Would love to have someone that knows what they're doing to fix mine. I tried some new pellets and it's not working. The pellet basically just drips/falls out of the barrel. Know anyone in western NC that may know how to fix it. I took it to a local gun shop and they wouldn't look at it.
Hi I have crossman .177 it’s not getting the pellets out , I have to shoot about 7 times before the pellet comes out, some debris is coming out, do you know how to fix it, thanks
Maybe you piston seal is faulty? Is this a new rifle? Ammo shouldn’t make a difference as long as it is .177. Possibly the seal on the barrel is missing or damaged? Have you ever taken the rifle apart?
It’s about 20 years old , but I keep it in good shape, but I kept it in the shed outside throughout summer and winter, maybe seal is not good anymore. I never took it apart, but after watching your video I’m going to try
You will have to either take yours apart and take measurements of the stock stuff then get another spring with the same diameter but thicker coils or more coils.
I to be totally honest want to go back to the light factory spring at about 490 fps it was just a lot easier to shoot. The big spring makes the recoil get very sharp and cocking it is a workout. I guess it depends what you want to do with it. For target plinking 600 is what I would recommend
Try all copper pellets...expensive af...but they're light and retain their shape on impact...they do like 5x the damage....i used to shoot them into a block of wood , pick them out and shoot them again
@BROTUNED nope...I think they were like 29.99 for 50 at cabelas..real expensive...saved them for my best kills hahaha jack rabbits took a pounding when I was in Edmonton 😅
100 % money 💰 is definitely not everything! I have enough to get by and that’s fine with me just want to enjoy the short time we have here. I enjoyed reading your comment. Have a great day sir
I've heard that an alternative way to add potential energy to your existing spring is to stretch out each coil slightly - so that the entire spring becomes marginally longer, and so when it is compressed it holds more potential energy - is this true? Cheers!
@@BROTUNED same place as my favorite store.AGS. if your ever in London and want to make a couple bucks I have a crossman magfire mission that is screaming for a mod. Apparently it's just filling a hole with jb weld. Don't trust myself to do it though.😃
As long as it's legal where you live, you can probably make an effective moderator out of PVC pipe with a foam insert or lining.. All you'll need is some pvc pipe slightly smaller or same size as the end of the barrel , a heat gun, a saw/dremel, some foam, and some tape. Probably would look custom (weird)...but it should work.
Peter V yes that would definitely work but would be illegal in Canada not to sure what the laws are in the states so I would definitely look into that before making anything
@@BROTUNED .. That's why I started with the legal disclaimer. One day I wish it will be legal here in Canada like the UK... would be more sensible to help people's hearing and noise pollution wherever the guns are used.
Yes I agree 110% but unfortunately all our government wants is to eliminate guns all together but wouldn’t that be awesome. The liberals are making hard drugs legal because that makes sense lol 😂. But guns are the problem they say. Smh 🤦♂️
where can i buy a stronger spring?
Vortekproducts.com
Moronic how the govts of certain countries see these as Firearms .In the 70s we have 20 ft lb air rifles .The one and only reason the 12 ftlb rule came in was to protect the British air rifle makers as they could not compete with the HW german make. Treating adults like kids is moronic
Most of the laws are idiotic and they say it’s to prevent crime lol people committing crime don’t care about the law anyway so just let us have some freedom
The more laws, the less justice-Cicero. Great video! @@BROTUNED
I simply dont follow these ridiculous laws Im surprised more people dont - especially the Britts .
What ever you say but you really should do the math . 👍
Our government class gel blasters, paintball guns and Airsoft as firearms. We still have real guns just need a license
They have these things now, they're called 'workbenches',..or something like that...
🤣🤣🤣
Just for balance of course…
Many years ago a friend of mine, whilst putting an Ox in his Hw35 got the breech block cross threaded.
He brought it over so we could mount it in my jig and hopefully resurrect the situation.
Well..couldn’t get it out so I held the breech tight with a leather gauntlet, while he twisted.
Some you guys will know that the HW spring carrier is roughly cut and splayed out in a cross shape - remember the roughly cut bit, it’s important.
Yep..we twisted..something thudded onto my thumb and the spring went airborne.
The first sign of trouble was that there didn’t seem to be a proper thumb in the thumb of the gauntlet any more.
There was a neat “v” shaped cut in the leather where my thumb should have been.
The spring carrier went through the leather, hit the top of the base of my thumb, went through down to the bone and dislocated it so it was laying next to my wrist.
One surgery and plenty of ribbing later, all was good.
Still got my Venom arms
HW 77k, must be 35years old and I’d still rather hunt with it than use my pre charged rifles.
Ouch
Make two short pins the size of the trigger group so that you can push out the long pins and leave the two short ones in place to keep the trigger group all in line and it makes assembly a doddle as everything is held in place and the safety simply slides in again no problems I made mine from brass rod and they are a godsend for servicing the rifle. The video is great and the results are very good you are doing a great job. And Nice to see someone actually doing things the safe way. Keep on keeping on stay safe from the UK.
The space of the compressed spring is already determined so that it engages, what is your idea? Buy an equal spring but of better quality. greetings
Excellent idea making the spring compressor. Makes the job alot easier 👍
Your method of assembling mainspring is definitely ingenious.
I have a cheap B2 Chinese. 22 air rifle that the spring got weak after couple of years. So bought a vortek spring for the rifle same length as the old one played hell getting the new one in. And cocking was hard also. So I cut the new spring down a couple of coils and flatten and polish the end. That rifle shoots 10 time better then when I first bought new awesome now. I even got one of their moly seal for that rifle even better. Vortek Inc. make great products for your air rifles American made from Michigan. More fps dose not mean better accuracy that's what you want accuracy with the right fps. And the right pellets also. Good luck bud.
I took an HW 80 up to 24 ft-lbs then dropped it back to 18 ft-lbs if it's done right you get very little recoil. At 24 ft-lbs the group size at 35 yards was around 10 inches at 18 ft lbs the group size was < 3/4 inch
I recently put a Vortek PG4 kit in my TX200 HC. I couldn't compress the new spring in by hand so I used the help of a ratchet tie-down strap, worked great!
Awesome job glad to hear it worked out for you! How does it shoot
@@BROTUNED Well, like you I'm a rim fire guy first. I'm still getting the hang of these rifles and want to see if I can outshoot my CZ LR at 50 yards. Now there's a video!!
Hi, I am about ready to change my spring - but I don't have a spring compressor or the means to make the version you use (I saw your video on how to make it and it is very good, it's just not something I can make at the moment). Is there a way to do this without a compressor? Ie by putting pressure yourself on the spring using the flat head of a file etc? I know it won't be as easy or as safe, but is there a way? Thanks!
Ya you do that but it’s a sketch situation so just spend $30 and build one so you can do it again safely from now on
“throw it in the spring compressor”
**does it with bare hands, pliers, and a flathead**
Yeah I don't remember using a spring compressor last time I did it
Please can you tell me is the new spring longer and or stiffer than the original one in the rifle .thanks
It’s a bit longer and stiffer
Can these springs go in red ryders?
Hi - this was such a useful video - thank you. I just have a few questions if you don't mind -
a) what's the name of that flat-lying vice-like thing with the screw adjuster clamped to the end? (The thing you put the barrel in to work on)?
B) I see you ordered the spring cut to 34 coils, but you said you realised you had to cut a couple more off. How were you able to tell that, and to know how much to cut off? (I ask so that I'll know when i do the same thing)
C) you mention something about "locking" the screws at the end- do you mean using "thread lock" liquid?
D) I'm going to order from the website you linked, specifying at 34 coils - the 142 Wire Spring 830OD. Will this spring fit most springer makes and models, or only certain ones? I have a variety of springers so would be good to know if it could work with any of them.
Cheers!
A) is a spring compressor I came up with to work on springers. I made a video on making it.
B)the reason I had to cut it was because it ended up binding up so I had to shorten it to allow the spring to compress. I cut a bit then tested it until the main spring compressed without any binding. Takes some time unless you make big incremental cuts
C) blue locktite is a good idea on anything that moves or vibrates
It will work in some for sure 👍🏻 but there’s a lot of springers out there so I’m sure it won’t fit in a good majority of them
this was one of the most enjoyable vids i have watched on tweaking air rifles , and has helped me gain a little more confidence to have a go on my own rifle as and when i need to GREAT JOB thanks for taking the time to share this , stay good from uk .
Thanks so much Peter!
So did you try taking it apart?
Not yet been busy with other content
7:01
I have a Air Hawk Elite one pump pellet rifle the ball that rode on the barrel that helped cock it came off in the spring came out but the ball fell down in the barrel
Flatten both ends of the spring, grind flat then polish to a mirror finish. Hope this helps you
Thanks very much for the tip I’ll give it a go
Why mirror finishing
@@brodylockley3141 The spring rotates when compresses and uncompressed so a rough finish after flattening hinders the rotation. The smoother the whole firing cycle will increase accuracy
@@DiscusRussell thank u
Just to let you know, your spring end is not finished correctly , you should heat it up with a blow lamp then when it gets red pinche the top coil so its inline with the coil unneath it pointed nose pliers then let it cool down naturally before placing it back into the action.
Bullshit. You have to temper this end of spring after inline coil modification. Otherwise this end of spring is soft. Ofcourse you have to smooth the ends of spring on both side for mirror surface. This method prevent vibrations, make shooting softer, and reduces gun kicking.
@Hieronim Gąbka Big Bull Shit you are stating, you collapse the spring with heat then pinch it to the coil underneath it , you let the spring cool down naturally no need at all for water or oils. It appears you know nothing about Springer Bull Shiter .
Thanks for sharing this I’ll have to go back in and change this
15 years ago or so I replaced my spring in the Quest B19 with a Air Rifle Headquarters Tarantula spring that dieseled and broke. I since replaced with Air Rifle Headquarters E3650 spaced with a washer along with their Apex seal they sell. 900fps
That’s not bad at all
Thanks man good vid, i learned tomorow i’m gonna make your device i realise i have that same c clamp and not such a thing yet. Pretty handy
Glad I could help it just makes it so much easier
thank you sir I learned again about the length and the diameter of the Main Spring less 2.3 !!!
I’m glad you enjoyed the video. I enjoy reading the comments
This is exactly what i was looking for. Thanks a lot
Not a problem! Have a great day
What brand of pellet rifle is that dude ? Never seen one exactly like it. Great work on that spring compressor. That comes in handy for sure. Great work thanks for the video dude.
It’s a ruger air hawk 177 495 fps
It's not just me who wants to make things more powerful than they are intended lol 😆
you are never alone...lol
People always want to be better. There's even a UA-camr modified his break barrel into a gun that fires using nail gun powder loads.
That’s awesome what’s the channel I’m curious to see this in action
@@BROTUNED I believe many countries did it but the ones I found mainly Indonesians. This guy demonstrates how the muzzle flash would look like if a nail gun powder load (purple code = strong charge) was placed into the drilled BSA barrel (Indonesian limit is 4.5mm, powder loads is 5.5mm, rim 6.5mm)
ua-cam.com/video/QAL3YRPdZyI/v-deo.html
@@BROTUNED Here's another one, this guy shows how he loads the powder load and uses modified piston as firing pin. The making process can be found in his channel.
ua-cam.com/video/qw8FOIZAK7Y/v-deo.html
We jus need the lil table u have for sale ?? 😂😂
No front spring guide..... 😮
Never had one
Hi mate- from the catalogue you link, there is a "148 Wire Spring 905 OD".
I've figured out this means Outer Diameter is 0.905 inches = 22.5mm.
What I don't understand is the "148". Is this the strength/ thickness of the wire itself? If so, is 148 a good standard to stick to? Cheers!
I’d have to check on the order form but I think .148” would be the thickness of the wire
@@BROTUNED Cheers mate, I appreciate that you take the time to reply to questions!
Happy new years Ryan. Would you have any links or know who could mod my webley tracker. Thanks from Vancouver Island.
No sorry not really familiar with that one
Should use a nitro piston spring with a 5/16 shaft and piston should be 155 mm long
Hey!
Great video, very good illustrated procedure. What is the source for the spring you used?
Dave
In the description it’s a vortekproducts.com spring
Hi thanks for reaching out. I purchased this custom spring from vortex products.com
The only problem with fitting a stronger spring is that it makes it harder to hit the target to much kick back
I agree 100%
I did this once never again wast of time makes the gun inaccurate. And rough to use.
The best ones I have found have a heavy stock to compensate.
Before anyone complains about this video please remember it was made for “scientifical” reasons 😂
Please take care if you don't have a Chrono or an FAC as if you get caught with a gun over 12 ft lbs the punishment is 5 years in prison no excuses not knowing the power is no excuse
This is correct it becomes a firearm over 500 fps and you must treat it and store it accordingly
The sort of air rifle that does well to hit a phone book.
Junk.
Managing to get 5 years in prison with it would be tragic.
Like your gun jig,im making one of those bad boys. Will make it loads easier 👍
It’s so much easier than trying to do it without this. The factory spring was fine but as soon as you upgrade it it’s a must have
Great video thanks, u made a Perfect spring compressor, I’m gonna make one 👍
Glad it helped
As a kid i used washers to compress the old spring.
very satisfied with this product
Thanks
Great job on the clamp. Thanks for sharing BT
Thanks for watching!
Power is nothing without accuracy, what are your groups like at say 30 yards, ?
Definitely not as good as the lighter spring. I know what you’re saying though.
Wow some countries have super lame airgun laws.
Ya your not kidding and the gun laws are even worse
Oh my god I just read the description 😮
Why you think the 2nd amendment is such a hot topic in the us, once they start it won't stop till we're hunting with slingshots.
Give me 12 foot pounds air guns over submachine guns anyday. The guns ordinary people can buy in America are just pure insanity.. life is so cheap in America. So sad
@@colly7912 well sub machine guns are illegal in America so brush up. Handgun, shotguns, rifles, even the big bad ar-15 (which is NOT a machine gun) ALL require a background check and a CLEAN record. Bad people do bad things whether they have a gun or a butter knife.
What were the previous spring readings? Connot see how much improvement there is??
It was a 495 fps rifle
So, how many FPS was it before?
Wish you had a before and after on this gun.
It’s a 495 fps gun originally I believe it was in the 460’s before any mods
Just found your vid timely. Opened up my Benjamin Classic 22 to see what is up. Chrono showing 426.
Not much preload in the spring as I put a little pressure on cylinder the main support pin fell out...
Gets better, Piston needed to be forced out using a probe to slide out of sleeve. Found scrubbing on the piston and ID of sleeve. Seal had metal filings embedded in it. Got pics to prove it.
Removed spring and found one end squared of and reasonable smooth, However the other end appeared to be hacked off with bolt cutters and not squared or cleaned up. On the end of piston, seal end, there is a small hole drilled through not centered, not done obviously on a lathe...Metal chips....
Got some work to do but need, to replace the seal and spring for sure after I calculate an appropriate length. Then lotsa polishing and lube. If this is how they "detune" for CA Market am not impressed. Bought this brand new and wasn't cheap at that time. Wish me luck cuz, skill is no problem here.
Am not on the Quest for more FPS, just what I paid for.
Just subbed and liked.
Ya I think they just detune them as fast as possible to get more out. You will have a great springer if you do all that for sure. Let me know how it turns out. Remember it magically turns into a firearm after 500 fps so a pal is required. Not sure if you have one but be mindful of that. Cheers buddy and good luck!
Man what a good video....I was really impressed with the gun vice may steal your idea its perfect!!!!
Ya good ahead it’s very simple to make and you don’t need any expensive tools
Makes it so much easier
It's one of a kind!! Thanks for sharing
Your welcome Dan! Cheers and enjoy
Peter Gore Seer,
There Are Some Fantastic Springs Sold, Oval Shaped Springs. There Are Some Guns With Barrels Bent.
Look for an OX spring square section
Nice enjoin hebackground. What style o yu play? Frailing, traitionalor Earl Scruggs picking? I'm a bluegrass and d time rythm and flatpicking guitarist myself. I have a Hatsan model 85 .22 open sights which I'm really enjoying. 850fps.
That’s my Dan Electro DC 59 bass guitar. I mostly play punk rock and metal on both bass and guitar.
That is the only other gun like that i have ever seen...that is the same as mine...is that a spa xt208
Excuse me, what was the original fps of the air rifle? was it 500 fps !
But after changing the spring with thicker one, you gained more than 380 fps? so 500 fps air rifle became 880 fps air rifle now?
Could you please let us know also after long term use what happaned? any problem so far?
Ya it was a 495 gun before
Hi friend, where did you get the new spring from? Thanks I am in Canada too.
Search up vortek springs
They have springs like this with different sizes and very strong at most hardware stores that’s equipped with a good stock of things like springs to bearings.
What makes a spring stronger, the thickness or the number of the coils?
I’m guessing the thickness and the number of coils would make it stiffer.
Probably the thickness
@@rileybeer2836 if you strengthen spring surely recoil will be worse?
I've read about the Ox Accelerator mainspring are square section and thus provides 40% more compression and power. If you're familiar with misumi spring you'll know square are better than regular round section coil.
How it's treated during the manufacturing process as well as what it's coated with will also overall improve your spring quality and durability.
Wowww... top gun..
greetings one hobby friend. let's drink coffee together☕🍵👈
What I am interested in is how harsh is the recoil and what is accuracy like now?
With the big spring it’s a bit much going to go back to the previous one for sure. Not worth the trade off
@@BROTUNED been down that road years ago there is only a certain amount of volume for air in an airgun and using a heavy spring creates piston slam and harsh recoil not to mention the strain on everything cocking arm, contact points and trigger sear. If you make another video maybe explain that to the views, I am afraid people new to airguns, may destroy a perfectly good airgun
Ya I will make a new vid about this issue
@@jimstewart5008 I found out by accident on my HW80, many years ago, just adding a small weight inside the front of the piston & then cutting off four coils from the spring, that put the power up & made it more comfortable to shoot. The trouble was, it took it over our 12ft/lbs limit so I put a standard spring back in & brought it back to how it was. It was a good experiment though.
That’s very interesting
Great video man. Can you attempt this on a gamo speedster? to uprate the spring for more ft/lbs and fps?
Cheers
I’ll have to find one but I will if I can get one definitely
Thicker spring or same kind but longer spring may gives more fps (power) ???
I did do longer and got spring bind. So thicker was basically the only way but it lost its nice shootability. It’s back destined again so it shoots nice soft and accurate again
@@BROTUNED so if ı use longer spring, it will not increase the power? ı wanna buy longer spring so thats why asking ur longer spring resuts? lets say original sprign is 20 cm, but if ı use 23 cm same stiffer spring. will it increase the velocity because it has longer spring?
That's a huge clamp you've got there mate😄😄
Better to compress my springs 😆
Can u tell me the exact measurements on the spring if u know then please could on see the diameter on the sheet I can’t buy from vortek in my country
30mm x .142” x34 coils
How do we consider a stronger spring for upgrade? Is it longer, harder, or thicker than the original? Thanks.
Yes basically that’s correct ✅ but don’t go overboard on thickness because you’ll get coil bind and make cocking it way harder for not much return in velocity. I found the gun shot best at around 600 fps
@@BROTUNED Noted, thanks for the tips.
We're can you order stronger springs please.
Vortekproducts.com is the site I believe
Should have bought yourself a table before the spring 😂
True enough lol
I used to do this when I was ten I used my weight to compress the spring and tap the pin out easy you don't need jigs and clamps crappy tools
You do when your old , 👴🏼
😂
I should know 😒
I’m just trying to make it easier and less sketchy for myself and I was bored
Can u tell me the exact measurements on the spring if u know them please could only see the diameter on the sheet I can’t buy from vortek in my country 😢
I’ll have to check the paperwork again I can’t recall the specs anymore
Anything over 12 foot pounds makes the gun less accurate simple law of physics proven . Doesn't matter what make of gun more important is gun weight but the laws of gravity × physics is finite. The point the pellet is less than a quarter of the way down the barrel at 800 fps that's fact that's life . Good video.
I enjoy it most at around 650 fps but I just wanted to see what it would do
Why didn’t you put sheet down on that lovely floor
I was careful
Any tips for improving the fps on the glock 17 bb gun gen 3?
I have never looked into it but if there’s a will there’s a way
ive been looking for a spring upgrade for my Beeman silver Kodiak dual cal.i want more power
Check out vortekproducts.com/
you think it possible to 3d print a spacer to insert into the airgun to get higher fps whit the same spring?
Oh I’m sure you could 100%
Test and tune basically
I had a crossman phantom . 22 500fps pellet gun from Walmart 99cad. I ordered a spring from vortek air springs... Brought it up to 1200 fps lol couldn't even keep a scope on it without a stop... Fuck it had some power... The spring was 12 bucks and like 30 to ship it to Canada lol well worth it
Fast little rifle!
Thanks. Always bothered that can't get ones higher then 500 fps here in canada like at Candian Tire and just bought one and want to get it closer to 1000, so will definitely try this :)
@sRecollet just message them tell them what kind of gun you have and what your looking to do
@@colbtron OK thanks. Checked out their site and seen like 15 listed but wasn't sure which one(s) would be compatible. Will definitely do that, thanks :)
@@sRecollet where are you from ?
How would you s screw the end cap back on say if it was a hw 80 with it being under pressure
I guess you couldn’t unless you can figure out a way to hold the tube securely and have the back exposed
Another Great video. Thank you so much.
Cheer
Cheers Donald
If you don’t have a pal license and make a 495 fps into something over 500 fps would that be illegal?
Yes it magically 🪄 becomes a firearm. Isn’t that crazy
@@BROTUNED oh how I love canada
It’s only going to get worse
@@BROTUNED can’t wait for bill c21 to pass
Why?
I CAN`T BELIEVE YOU DIDN`T TAKE THE PISTON OUT. POLISH IT AND PUT A NEW SEAL ON IT AND LUB IT UP FOR REASSEMBLE.
It’s easy enough to do just testing the main spring in this video. So the only variable was the spring
And mill out slots in the piston to make it lew weight
@@crazycressy7986 what is lew weight
Hi , nice job , how much did you gain and where did you get your spring from .
Over stock it almost doubled the velocity and I purchased the springs from vortek.com
OK , Thank you and that link does not work .
vortekproducts.com/ourstore/index.php?route=product/category&path=64
I couldn’t remember the exact site but it is vortekproducts.com
That link worked and Thank You :=}
How much increase in velocity??Thanks
Wasn’t much but the more I go faster the more I want to put the light spring back in for quietness and light recoil. But I think it was in the 100fps range
Found an older one than this in my dad's stuff.....he died a few years ago. Would love to have someone that knows what they're doing to fix mine. I tried some new pellets and it's not working. The pellet basically just drips/falls out of the barrel. Know anyone in western NC that may know how to fix it. I took it to a local gun shop and they wouldn't look at it.
Does it cock and spring back when you pull the trigger. May just need new seals and to clean up the inside of the piston tube
@@BROTUNED , yes, it does. I have no idea if my dad ever did any of that so I'll try to check it out and see. Thank you very much!
Ok good luck with the gun hope you get it working
If its a .22 the old ones are 5.6 not the newer version 5.5 tryfinding the old style ammo
@@martinkelsey275 , thank you
I wonder how much dieseling would increasing fps with this setup.
A lot but no accuracy though no consistency
Is it an umarex ruger hawk air rifle?I just got one myself today,if it's the same model,I can just apply the spring size you use to mine
It is a ruger air hawk 495 fps and in .177
@@BROTUNED really appreciate
@@BROTUNED How many coils that spring still have after you cut it,I want to save that step so I don't need to cut and grind myself😂
No problem thanks for your comment
Outstanding!👍👍👍
Thank you so much Catherine Harris really appreciate that. Cheers!
No Lube ?
Lots in there
Que resorte le puso al rifle para que tire mas fuerte? Expliquelo por favor
I went to vortekproducts.com you can find the springs there
Hi I have crossman .177 it’s not getting the pellets out , I have to shoot about 7 times before the pellet comes out, some debris is coming out, do you know how to fix it, thanks
Maybe you piston seal is faulty? Is this a new rifle? Ammo shouldn’t make a difference as long as it is .177. Possibly the seal on the barrel is missing or damaged? Have you ever taken the rifle apart?
It’s actually marksman 177, Do you have a video how to replace the seal
It’s about 20 years old , but I keep it in good shape, but I kept it in the shed outside throughout summer and winter, maybe seal is not good anymore. I never took it apart, but after watching your video I’m going to try
Could be rusted inside. You’ll have to check it out and perhaps hone the cylinder and get a rebuild seal kit online.
Thank you
Hey Where can I order a spring for my gamo varmint air gun in Canada ???
Vortekproducts.com
Love it
Thanks buddy we should do a video together sometime
@@BROTUNED 100% my man... 100%
I have a 7,5 joule umarex .177 air gun and i want to mod it, what do you suggest? Like lubing the piston or what spring should i get, Thanks🙏
The biggest thing that makes the biggest difference is changing the main spring to something stiffer. Vortekproducts.com
@@BROTUNED i have no idea what i should get, any ideas?
You will have to either take yours apart and take measurements of the stock stuff then get another spring with the same diameter but thicker coils or more coils.
What increase in fps did you get? You never showed the results - only the final result. Was it worth it?
I to be totally honest want to go back to the light factory spring at about 490 fps it was just a lot easier to shoot. The big spring makes the recoil get very sharp and cocking it is a workout. I guess it depends what you want to do with it. For target plinking 600 is what I would recommend
Try all copper pellets...expensive af...but they're light and retain their shape on impact...they do like 5x the damage....i used to shoot them into a block of wood , pick them out and shoot them again
Oh ha ha that’s crazy the seriously don’t deform?
@BROTUNED nope...I think they were like 29.99 for 50 at cabelas..real expensive...saved them for my best kills hahaha jack rabbits took a pounding when I was in Edmonton 😅
That is expensive
@@BROTUNED where are you out of?
Like city? Country?
Man u did what soo many wish 2 do ..Time constraints..😔
Life i$ more than cha$ing money 1🤫
100 % money 💰 is definitely not everything! I have enough to get by and that’s fine with me just want to enjoy the short time we have here. I enjoyed reading your comment. Have a great day sir
Can .22 spring be put in .177 rifle?
Yes
I've heard that an alternative way to add potential energy to your existing spring is to stretch out each coil slightly - so that the entire spring becomes marginally longer, and so when it is compressed it holds more potential energy - is this true? Cheers!
Makes sense but I haven’t tested it
Looks like a pain in the ass. I'd pay you to do it but im in London Ont. Canada eh.
I’m just up near Peterborough. Cheers Donald
@@BROTUNED same place as my favorite store.AGS. if your ever in London and want to make a couple bucks I have a crossman magfire mission that is screaming for a mod. Apparently it's just filling a hole with jb weld. Don't trust myself to do it though.😃
Ok definitely if I’m out that way we can plan something
@@BROTUNED TYSM
Your welcome!
where did you get the springs and upgrades
I got my springs from vortekproducts.com
@@BROTUNED are they still in bussiness ?
I believe that they are but haven’t ordered from them in many years so not positive
Where can I get a spring press like that?
I think you just have to e to build one I haven’t seen any for sale anywhere
what kind of fish do you have?
Lol 😂 no clue the kids picked them
Dude.... thank you!
No problem cheers!
Can I put a stronger spring on a youth break barrel
I don’t see why not. Would make the cocking harder though
Where did you get the spring from?
I believe the website is vortek.com or something like that
Does widening the end of the barrel with a drill affect performance
The muzzle would ruin performance I just matched the breach end to get the best flow through the port
500 fps limit? Sounds like everyone wouldn't be able to get anything more than a multi pump air pistol.
The Canadian gun law is a joke.
You’ve got that right
Ryan, I have a Ruger Air Hawk .177 and would like to fit a moderator to help make it more backyard friendly. Any ideas?
You’d have to get a gunsmith or machine shop to thread the barrel 1/2x28 if it’s thick enough then buy a can
As long as it's legal where you live, you can probably make an effective moderator out of PVC pipe with a foam insert or lining.. All you'll need is some pvc pipe slightly smaller or same size as the end of the barrel , a heat gun, a saw/dremel, some foam, and some tape. Probably would look custom (weird)...but it should work.
Peter V yes that would definitely work but would be illegal in Canada not to sure what the laws are in the states so I would definitely look into that before making anything
@@BROTUNED .. That's why I started with the legal disclaimer. One day I wish it will be legal here in Canada like the UK... would be more sensible to help people's hearing and noise pollution wherever the guns are used.
Yes I agree 110% but unfortunately all our government wants is to eliminate guns all together but wouldn’t that be awesome. The liberals are making hard drugs legal because that makes sense lol 😂. But guns are the problem they say. Smh 🤦♂️
Awesome tutorial, thanks!
You are welcome
You are a Animal!. Cave men have more finesse.
Finesse is for the weak
did you try drilling holes in your piston to get it lighter AND MORE FPS
Lol 😂