How To Rebuild Broken Axle Shaft || Amazing Welding & Machining Technique

Поділитися
Вставка
  • Опубліковано 10 гру 2024

КОМЕНТАРІ • 46

  • @davebenedict7986
    @davebenedict7986 Рік тому +5

    Pretty creative chucking that shaft up in the lathe to weld it. I wouldn't have thought of that. For similar shaft repairs, you might want to wrap an empty aluminum can around the shaft close to the weld joint to keep the spatter beads off the shaft.

  • @Farm_fab
    @Farm_fab 2 роки тому +6

    My uncle used to modify axles on his lathe, but he never welded them solid until he made sure there was no runout. He would tack it together, then he would turn the lathe chuck , tapping it with a hammer to straighten them. When he had it close, he would make precise measurements before completing the weld.
    I didn't see a rotary ground on this lathe, but they COULD have used one.

  • @robertmccully2792
    @robertmccully2792 Рік тому +1

    Good idea but should have clamped some L stock to both axel's then spot welded and check for alignment, then stick back in lathe.

  • @sjv6598
    @sjv6598 2 роки тому +21

    5:05 holy moly look at that run out! The truck will vibrate your false teeth out 😂

  • @JohnPittaway
    @JohnPittaway Рік тому

    A nice piece of work, Sir.

  • @AndyL940
    @AndyL940 2 місяці тому +1

    That will break first clutch release

  • @Farm_fab
    @Farm_fab 2 роки тому +2

    A little coolant on that cut would stop the squealing.

  • @allis732
    @allis732 Рік тому +1

    Hope they get the bent side of the rim offset to that wobble

  • @sergioramses2615
    @sergioramses2615 Рік тому +1

    I notice the shaft from the point of the welding it wasn't set straight enough it was unbalance.

  • @murlisundaran6151
    @murlisundaran6151 2 роки тому

    Which tool tip is used for turning of axle shaft

  • @Samsungsamsung-qo8xh
    @Samsungsamsung-qo8xh 2 роки тому +1

    Когда сварил Центробежност👎 пропал!!

  • @MuliaPuja-p8x
    @MuliaPuja-p8x 3 місяці тому

    Eletroda the name pliese

  • @safreedinternational6461
    @safreedinternational6461 2 роки тому

    Pls what type of electrode did you use eg cast electrode, stainless electrode or steel or Iron electrode

  • @bobweiram6321
    @bobweiram6321 Рік тому

    Two steady rests, one at each end would have increased the concentricity.

  • @mandylad
    @mandylad Рік тому

    what kind of rods are used to weld that?

  • @mauricionavas2816
    @mauricionavas2816 2 роки тому

    que tipo de electrodo se utiliza ? alguien que me escriban porfavor

    • @sabinogordo1423
      @sabinogordo1423 Рік тому

      hola supistes que electrodo uso

    • @odiseoeltres1612
      @odiseoeltres1612 Рік тому

      Puedes meter raíz de 6010, limpiar muy bien y después pasar 7018 o 9018, con eso debe de quedar, el problema más grabe es que quede recta para evitar vibraciones como se muestra en el video, ese trabajo no sirve, te puedes apoyar con alguna base que esté a mismo nivel todo y que no permita que se incline a algún lado por el mismo calor de la soldadura

  • @fivepointeightnate
    @fivepointeightnate 2 роки тому +3

    At least he knocked off all the welding spatter so it wouldn't be out of balance 🤣

  • @rogeliogarcia193
    @rogeliogarcia193 5 місяців тому +1

    Mejor hubiera echo rosca centro y al otro la la punta tornillo para aclanje y listo a soldar 😂

  • @akhilt.a8332
    @akhilt.a8332 Рік тому

    TIG WELD WOULD HAVE CREATED LESS BENDING

  • @richardtharp1608
    @richardtharp1608 2 роки тому

    That axle may Work for a Time, but it was Bent on the long end Piece BigTime.. Watch as it Jumps Up and Down towards the Left while Turning Fast.. NOT GOOD

  • @marcosmendoza4866
    @marcosmendoza4866 Рік тому

    No me soldes arriba del torno por el amor de jebus:V

  • @Farm_fab
    @Farm_fab 2 роки тому

    The procedures for repairing a floating axle are well established. I'm not a machinist, but I am a welder and I know how this should be repaired. The final product looks rather good, but they had a lot of chatter on the carbide on the lathe which caused the rough finish.

  • @andripoetra2007
    @andripoetra2007 2 роки тому

    👍

  • @daleolson3506
    @daleolson3506 8 місяців тому

    Where was the ground connected?holy cow the horrible

  • @lsmartino
    @lsmartino Рік тому +1

    Eso no sirve.

    • @pacohernandez6742
      @pacohernandez6742 Рік тому

      Porque explíqueme porque tengo un caso así

    • @lsmartino
      @lsmartino Рік тому +1

      @@pacohernandez6742 Porque la soldadura no tendrá nunca la misma resistencia del acero, aparte de que en el proceso esta destemplando el material original.
      Puede intentarlo, pero va a perder su tiempo ya que la reparación no será ni duradera ni confiable.

  • @crazymasina8524
    @crazymasina8524 2 роки тому

    Me sad

  • @cleberrupay6388
    @cleberrupay6388 2 роки тому +1

    Falto centrar bien

  • @Frag_granade
    @Frag_granade 2 роки тому +1

    This ain't gonna work because they use a heat treated steel to make axles and welding it with regular metal won't help at all