You saying, "I thought to myself, "What could make this garage better?" And the answer is more cleats." totally deadpan made me laugh out loud. Thanks for the informative video, I really want to do this in my art studio, and the birch looks great!
Just a quick question for anyone who might know the answer. Would it be easier to cut the 45 degree angle as your cutting the strips? To me it seems you could skip a step if you did. I know that if you set up one saw at a 45 that each side would be angled but you could use either 2 saws, one set at a 45 and the other to cut the flat bottom, or just have angles on top and bottom so that either way you need to place the board it works. I’m just learning woodworking and CNC carving so this is an honest question I had while watching. Great video, I can’t wait to start my organization wall.
For those of them that are watching this and saw the outlet change. I want to clarify something. That was very dangerous what he did. It may seem innocuous now but he switched a 15 amp outlet with a 20 amp outlet. The wiring I'm certain is for 15 amp only and by putting a 20 amp outlet on it you allow the ability of somebody who has a 20 amp device into it, and could cause a fire because the wiring is not designed to handle it or at least it would trip the breaker constantly. You can tell because it had that little slash 90° on the left prong. So 20 amp devices have that prong Twisted 90° so it can plug into that spot. You should look for Outlets that do not have that problem to match what's there. However if that is all you have make sure you write in Big Red Letters on the outlet cover 15 amp outlet only. So people know that even though a 20 amp device could fit into it not to use it. Something had to do similarly. I paid $5 for case of 30 gfic Outlets that were 20 amps and rather than spend $7 every time I wanted to put another gfic someplace I just filled in that slot with epoxy, and wrote on it 15 amp only so nobody tried to cut out or chisel out that epoxy covering the hole thinking that it was an accident. May sound stupid but electricity is something you should mess with and you got to be very precise with.
Excellent comment. Dan is correct in saying you cannot install a 20 amp outlet on a 15 amp circuit. It is against code and is a fire hazard to do so. In the video, I replaced the 15 amp outlet for a 20 amp outlet on a 20 amp circuit so it was done correctly. I replaced it because I plan to run heavier machinery on this outlet (band saw, drill press, etc.) If anyone reading this is looking to replace an outlet, you must first go to your breaker and check the number on the breaker switches (15, 20, etc). Also check that the circuit is using the correct gauged wire (14 vs 12). For those that want more info, here is is a link to the electrical code: up.codes/s/outlet-devices. Also, here is a link to a video to that I go into more detail on replacing a regular outlet for a USB one: ua-cam.com/video/l-Y-aL_QWbs/v-deo.html
Happy to see someone else adopt a smaller cleat size to extend a sheet of ply! I was in the sign business for years (80's - 2003) and we used 2" french cleats to hold large sandblasted signs!!! The key is to hit a stud with the fasteners or use anchors! Those 5" and 6" cleats sizes I see folks posting is just a waste of valuable lumber and over-engineering for what most DIY's are going to hang in their garage/shop! Great Job! #hardworkpaysoff
Thank you. Clear and informative, in fact excellent. A shame that my 'garage' (is was a barn at some point) is at least 200 years old and nothing in it is square. The joys of living in the UK.
This was exactly what I've been looking for. I dont have a garage so I wanted something that wasn't shelving to store my tools on. This is perfect, thank you
Overwhelmed by the support. Thanks so much for watching and giving tips from the $Thanks button above. Helps so much. I've received a few questions, so here are the measurements I used: The cleat itself is 1.5 inches on the shorter side and 2.25 on the longer side The gap between my cleats is 2.25 inches, but you could go 2.5 inches or more. From base of first cleat to top of second cleat is 6.75 inches. Base of first cleat to the base of second cleat is 4.5 inches. Hope this helps. I will eventually make a part two and will explain in detail. Thanks again.
This is amazing! I wish I found this years ago! (When I bought a wall system that’s still sitting in a heap on my garage floor). It’s time to start organizing. I’m already realizing I could have built things better myself (slow of course as I’m new) but better in that it works for my space and what I have!
So awsome. Thanks for showing this , I didn't knew about this type of system. I temporarily bought some plastic standardized tool boards , but the quality is really crap. It can't really support the amount of stuff you can put in there weight wise. It starts to hang and the back parts it hangs on can easily break if not careful or like said weight overloaded using the whole bracket of holes filled. That being said this is my first own setup for my shed , I just needed something in place. Now I'm in the process I'm getting to upgrading it into a wood tool wall. This really helps me out a ton because I had ideas how to do it but just not a design for it yet. This definitely gives me a blueprint for the universal backwall because that's exactly what I wanted. A system where I can design my own buckets or cabinets on. Because now I can make any design for any tool or material storage I need and fix it on there.
Just moved to a new home with separate shop. Loved this video, so helpful. I am cringing a little with how much more expensive the Birch Plywood is compared to a few years ago. About triple, but it makes such a beautiful feature in the shop. I have most of the same tools as well which is great for using the cordless power tools. I love my Ridged Pro series table saw and miter saw. They cut so clean and are infinitely quieter than my older equipment. The Ryobi cordless pin nailer is such a magnificent tool.
Starting my french cleat wall today, it was raining all morning and all my lumber was outside, tarped. Didnt feel up to getting wet but time is on my side
I am setting up my new metal garage. Need space to store everything. Will be following your tips from this video with a bit of a twist to accommodate the steel structure. Thank you so much for this video! I finally have my missing piece to my storage problems!
@@steveb7882French cleats hold a tremendous amount of weight, more than a shelf can. I have hung very heavy cabinets and filled them with tools on French cleats. The cleats are still holding well over twenty years. Besides that, there’s the nice thing of rearranging as the tools multiply. I had never thought of using plywood behind mine, I have always just secured them to the studs themselves. The plywood is interesting as it would allow a nice backdrop and easier to clean I imagine. It looks nicer that’s for sure.
What a beautiful job you did!!! I now want to reorganize my garage and make it as neat as yours!!! Just amazing how much wood has gone up!!! Thank you for taking the time in making this video.
I pick up pallet wood in my city. even the standardized Euro pallets companies can't return if there is like 1 broken board on them. Be sure to pick up the pine ones and not firewood since that's crap. Anyway I got a few addresses in my city now where I can freely pick it up because otherwise they need to pay money for throwing it away or having someone pick it up for taking it to the city dump. Yeah it's a bit more work but it's free that way. Put it thru a planer , plug the holes with wood glue and sawdust from the same type of wood sand the remains off and it's like you got brand new boards. Sorry if I'm too informative I don't know your experience in this , but yeah that's how I do it.
Definitely could work that way too. I used the 4x8 sheets mostly for looks. Plus the maple plywood was about 60% cheaper when I built my cleats than it is now in late 2023.
im 3 min. in and im already stopping your video to "like" your video and subscribing because your delivery is exceptional because you explain everything you're doing . not everyone is in the business and many DIY videos are made where the builder is making cuts or using material and not explaining ,,im a fan
good video thanks. One thing you can do for the sharp edges, is run the cleats through your tables say again, just taking off 1/2 of a ply layer thickness. This will also keep the plywood from chipping.
Good idea! I have ran them through removing about 1/16” - 1/8” off the tips, just enough to blunt the tips. I usually use a block plane as I enjoy hand tools more than power tools😂
Very nice. I have been wanting to do something similar and now I have an excuse to buy buy some more toys. One of those spiffy brad nailers will be a good start.
Great Job!!! Best french cleat video I've seen so far!!! I never knew about dust resistant electrical outlets, Thanks. One question? You mentioned using either 1/2" or 3/4" birch plywood on the garage wall. You used 1/2" plywood. However the shelves look like that are made with something heavier (see 4:35 min). Is everything else made with 3/4" birch plywood??
10:43 You are actually supposed to store tubes like that upside down.
Рік тому
Thank you for your sharing, could you post the link to Home Depot or Lowes where you got the birch plywood from? There are several options for birch plywood and I would like to choose the one most close with your woods. Thanks
great video, I swear you are the woodworker version of Zach from JerryRigEverything, you have similar tone and inflections, and even are bald to match!
Your wall looks great and I'm thinking of doing the same in my basement. However, I only have a brick wall and so, in order to cut-down on the number of screws in the brick, I think I would forgo the plywood panel and just add the cleats directly to the brick using Tapcons. What are your (and others') thoughts on many Tapcons into the brick wall? Strong enough? Would they loosen over time? Another option is to use the plywood panel and only use screws for the cleats that stop just before the brick. So, something like an 1.25" screw. Would that be strong enough?
You could put spacers so that the plywood sticks out from the brick further so you can use longer screws and use thicker plywood to make sure it is strong enough to hold the cleats up.
Just started my french cleat wall tool holder project. Just an observation, if your tool holder is long enough to hang over the french cleat below the one is is hanging on, do you really need the support blocks? Thanks for sharing!
Correct. If it’s hanging over the cleat below then you generally don’t need the extra back support. I suggest you have it hang over the bottom cleat .5 to .75 inches to avoid breaking the tip of the cleat.
Love it. Very handy and easy to replace the band. However it's not made for heavier cutting so would want to get a larger one if you plan to cut 2x4s or dense hardwood. For these more dense items it will cut them fine but the band will slightly bend, making an uneven cut if you go too fast.
How do you like that Wen band saw? I got their 7 1/4 track saw (with a powertech track) and absolutely love it. I want a band saw but can't afford/fit a large band saw so I was considering the Wen.
What is the total distance between the bottom of one cleat to the bottom of the one above it, sine each cleat is based on a 4in board cut at 45 degrees? Looks like you have a quarter of an inch or so of space when you hang an object from the wall.
Good catch. I've mentioned it on other posts and you are correct that I switched a 15 for a 20 amp outlet. You are also correct in that this is a 12ga wire on a 20 amp circuit so that change was intentional. Anyone reading this, you need to check the breaker box and make sure you don't put a 20 amp outlet on a 15 amp circuit. The opposite, 15 or 20 amp outlet on a 20 amp circuit, is generally up to code.
The cleat itself is 1.5 inches on the shorter side and 2.25 on the longer side The gap between my cleats is 2.25 inches, but you could go 2.5 inches or more. From base of first cleat to top of second cleat is 6.75 inches. Base of first cleat to the base of second cleat is 4.5 inches. Thanks for the question.
You saying, "I thought to myself, "What could make this garage better?" And the answer is more cleats." totally deadpan made me laugh out loud. Thanks for the informative video, I really want to do this in my art studio, and the birch looks great!
Wow, great job. And even if you don't move things around very often, french cleat looks very nice
Just a quick question for anyone who might know the answer. Would it be easier to cut the 45 degree angle as your cutting the strips? To me it seems you could skip a step if you did. I know that if you set up one saw at a 45 that each side would be angled but you could use either 2 saws, one set at a 45 and the other to cut the flat bottom, or just have angles on top and bottom so that either way you need to place the board it works. I’m just learning woodworking and CNC carving so this is an honest question I had while watching. Great video, I can’t wait to start my organization wall.
The most amazing thing about this video is the craftmanship he got using only Ryobi tools!
I didn’t see the logo on the bandsaw but I assume it was a Ryobi. I have some Ryobi tools. I like them
Thanks!
For those of them that are watching this and saw the outlet change. I want to clarify something. That was very dangerous what he did. It may seem innocuous now but he switched a 15 amp outlet with a 20 amp outlet. The wiring I'm certain is for 15 amp only and by putting a 20 amp outlet on it you allow the ability of somebody who has a 20 amp device into it, and could cause a fire because the wiring is not designed to handle it or at least it would trip the breaker constantly. You can tell because it had that little slash 90° on the left prong. So 20 amp devices have that prong Twisted 90° so it can plug into that spot. You should look for Outlets that do not have that problem to match what's there. However if that is all you have make sure you write in Big Red Letters on the outlet cover 15 amp outlet only. So people know that even though a 20 amp device could fit into it not to use it. Something had to do similarly. I paid $5 for case of 30 gfic Outlets that were 20 amps and rather than spend $7 every time I wanted to put another gfic someplace I just filled in that slot with epoxy, and wrote on it 15 amp only so nobody tried to cut out or chisel out that epoxy covering the hole thinking that it was an accident. May sound stupid but electricity is something you should mess with and you got to be very precise with.
Excellent comment. Dan is correct in saying you cannot install a 20 amp outlet on a 15 amp circuit. It is against code and is a fire hazard to do so. In the video, I replaced the 15 amp outlet for a 20 amp outlet on a 20 amp circuit so it was done correctly. I replaced it because I plan to run heavier machinery on this outlet (band saw, drill press, etc.) If anyone reading this is looking to replace an outlet, you must first go to your breaker and check the number on the breaker switches (15, 20, etc). Also check that the circuit is using the correct gauged wire (14 vs 12). For those that want more info, here is is a link to the electrical code: up.codes/s/outlet-devices.
Also, here is a link to a video to that I go into more detail on replacing a regular outlet for a USB one: ua-cam.com/video/l-Y-aL_QWbs/v-deo.html
You filling in an electrical outlet with epoxy seems a little more unsafe and against code to me lol
Happy to see someone else adopt a smaller cleat size to extend a sheet of ply!
I was in the sign business for years (80's - 2003) and we used 2" french cleats to hold large sandblasted signs!!! The key is to hit a stud with the fasteners or use anchors!
Those 5" and 6" cleats sizes I see folks posting is just a waste of valuable lumber and over-engineering for what most DIY's are going to hang in their garage/shop!
Great Job! #hardworkpaysoff
Thanks for watching Gene. Really appreciate the comment.
Thank you. Clear and informative, in fact excellent. A shame that my 'garage' (is was a barn at some point) is at least 200 years old and nothing in it is square. The joys of living in the UK.
Great video. Where is Part Two you mentioned?
This was exactly what I've been looking for. I dont have a garage so I wanted something that wasn't shelving to store my tools on. This is perfect, thank you
This is Brilliant, I would let my sealant stand upright
That was well done and well filmed. Kudos to you. But…..you did have a helper, small as he was.
Overwhelmed by the support. Thanks so much for watching and giving tips from the $Thanks button above. Helps so much.
I've received a few questions, so here are the measurements I used:
The cleat itself is 1.5 inches on the shorter side and 2.25 on the longer side
The gap between my cleats is 2.25 inches, but you could go 2.5 inches or more.
From base of first cleat to top of second cleat is 6.75 inches.
Base of first cleat to the base of second cleat is 4.5 inches.
Hope this helps. I will eventually make a part two and will explain in detail. Thanks again.
Okay, now pin your comment so it will be on top where everyone will see it.
Great video! I'd love to see the promised part 2 even if it's just a quick video that shows the holders you've built since this first one.
This is amazing! I wish I found this years ago! (When I bought a wall system that’s still sitting in a heap on my garage floor). It’s time to start organizing. I’m already realizing I could have built things better myself (slow of course as I’m new) but better in that it works for my space and what I have!
Just remember "If you can't find something, clean up until you find it" :)
For the cleat you also use a half inch ply wood or 3/4
Excellent job,man……..nice to see the little fellas lend a helping hand.
Literally the perfect instructional video!
Thanks brah
you can alternate the spacers when setting up the cleat. that way any imperfection in the spacers will cancel each other out.
Really enjoyed your video 👍
So awsome. Thanks for showing this , I didn't knew about this type of system. I temporarily bought some plastic standardized tool boards , but the quality is really crap. It can't really support the amount of stuff you can put in there weight wise. It starts to hang and the back parts it hangs on can easily break if not careful or like said weight overloaded using the whole bracket of holes filled. That being said this is my first own setup for my shed , I just needed something in place. Now I'm in the process I'm getting to upgrading it into a wood tool wall. This really helps me out a ton because I had ideas how to do it but just not a design for it yet. This definitely gives me a blueprint for the universal backwall because that's exactly what I wanted. A system where I can design my own buckets or cabinets on. Because now I can make any design for any tool or material storage I need and fix it on there.
Just moved to a new home with separate shop. Loved this video, so helpful. I am cringing a little with how much more expensive the Birch Plywood is compared to a few years ago. About triple, but it makes such a beautiful feature in the shop. I have most of the same tools as well which is great for using the cordless power tools. I love my Ridged Pro series table saw and miter saw. They cut so clean and are infinitely quieter than my older equipment. The Ryobi cordless pin nailer is such a magnificent tool.
Good job! Gonna make the same setup in my garage!
Starting my french cleat wall today, it was raining all morning and all my lumber was outside, tarped. Didnt feel up to getting wet but time is on my side
No ventilation behind the Wall will bring Mold. U should have put the Poweroutlet onto the Plywood by pulling it out.
Love the rest👍
Love it. I built my wall but struggling with the right organizational setup to use. I will be stealing many of your ideas!
You've sent me back to the drawing board, talk about timing, got my sheets delivered 2 days ago. Thanks for the great ideas.
I am setting up my new metal garage. Need space to store everything. Will be following your tips from this video with a bit of a twist to accommodate the steel structure. Thank you so much for this video! I finally have my missing piece to my storage problems!
Sounds great. Send lessons learned or pics when done. Glad this video helped you get started.
Buy shelves cheaper and easier
@@steveb7882French cleats hold a tremendous amount of weight, more than a shelf can. I have hung very heavy cabinets and filled them with tools on French cleats. The cleats are still holding well over twenty years. Besides that, there’s the nice thing of rearranging as the tools multiply. I had never thought of using plywood behind mine, I have always just secured them to the studs themselves. The plywood is interesting as it would allow a nice backdrop and easier to clean I imagine. It looks nicer that’s for sure.
Fantastic job mate! And looks aesthetic. Will need to replicate one day…
I'm glad there are so many tutorial videos out there that are helpful if you have a full on shop full of tools.
Man, you are a crack! Thank you so much for sharing. Extremely inspiring.
Łapka w górę za podwójnego pikantnego MacRoyala 💪💪 tu się zgadzamy
What a beautiful job you did!!!
I now want to reorganize my garage and make it as neat as yours!!!
Just amazing how much wood has gone up!!!
Thank you for taking the time in making this video.
I pick up pallet wood in my city. even the standardized Euro pallets companies can't return if there is like 1 broken board on them. Be sure to pick up the pine ones and not firewood since that's crap. Anyway I got a few addresses in my city now where I can freely pick it up because otherwise they need to pay money for throwing it away or having someone pick it up for taking it to the city dump. Yeah it's a bit more work but it's free that way. Put it thru a planer , plug the holes with wood glue and sawdust from the same type of wood sand the remains off and it's like you got brand new boards. Sorry if I'm too informative I don't know your experience in this , but yeah that's how I do it.
Hi from Czech republic. Very awsome video, thank you so much :)
Ahoj! Thanks for watching.
I have a very similar garage setup, why mount a plywood panel instead of just mounting cleats to the studs through the drywall?
Definitely could work that way too. I used the 4x8 sheets mostly for looks. Plus the maple plywood was about 60% cheaper when I built my cleats than it is now in late 2023.
Probably the easiest video to follow through for a beginner. Thank you
Nicely done, motivated me to do something about my serious lack of organization for stuff I cannot even get to at the moment.
Hello! Please tell me what that square is called that you also used as a straight edge with the hand saw? 2:40 Into the video. I need one!
I use milk crates and other things sometimes 2 nails can hold a tool flush to any wall
Really nice alternative to peg boards.
im 3 min. in and im already stopping your video to "like" your video and subscribing because your delivery is exceptional because you explain everything you're doing . not everyone is in the business and many DIY videos are made where the builder is making cuts or using material and not explaining ,,im a fan
Great video, and really clear. Was a part 2 ever made?
Love this. Was just thinking of making something along these lines. I will do this. Thank you.
Very clear explanation for making french cleats. Thank you
Great work. I am starting my French build soon and glad I ran across you channel. It also looks like you have some great help. 😀
good video thanks. One thing you can do for the sharp edges, is run the cleats through your tables say again, just taking off 1/2 of a ply layer thickness. This will also keep the plywood from chipping.
Good idea! I have ran them through removing about 1/16” - 1/8” off the tips, just enough to blunt the tips. I usually use a block plane as I enjoy hand tools more than power tools😂
wow very impressive work.
It was amazing. I like it and I want to make it one for my workshop. Can you just give me any plan?
Part 2 coming soon?
I loved your ideas! Simple, cost efficient, and clean.
Great video....where is part 2?
Similar style as the channel BlackTailStudios, I like it.
Awesome did you ever make video part two
This was brilliant, man. Thanks!
Dude, you are just awesome!! Thanks a lot!!!!
Why brad nails instead of clamps? Just curious.
Very nice. I have been wanting to do something similar and now I have an excuse to buy buy some more toys. One of those spiffy brad nailers will be a good start.
I didn't know you could do a project like this without Milwaukee and Festool power tools?
Great Job!!! Best french cleat video I've seen so far!!! I never knew about dust resistant electrical outlets, Thanks. One question? You mentioned using either 1/2" or 3/4" birch plywood on the garage wall. You used 1/2" plywood. However the shelves look like that are made with something heavier (see 4:35 min). Is everything else made with 3/4" birch plywood??
10:43 You are actually supposed to store tubes like that upside down.
Thank you for your sharing, could you post the link to Home Depot or Lowes where you got the birch plywood from? There are several options for birch plywood and I would like to choose the one most close with your woods. Thanks
Great idea, thanks for sharing
2:20 whats the background music?
Very nice. Some great ideas. I'm starting my Frech cleat wall build tomorrow morning and this helped me quite a bit, thanks again.
Great job!! 👍 😊
Looks great mate, I had to leave a comment because it was so easy to follow. I'll be watching your follow-up videos now. Cheers!
Very helpful and encouraging,, thanks a lot.
How did you manage the 1/8 blade on the cleat board? How many inches did each board end up being?
how thick is the plywood for the cleats? looks like it might be thicker than the plywood that went on the wall
Good job. Love it. thanks for the idea.
You bet. Thanks for watching!
great video, I swear you are the woodworker version of Zach from JerryRigEverything, you have similar tone and inflections, and even are bald to match!
Loved this. 😊
Your wall looks great and I'm thinking of doing the same in my basement. However, I only have a brick wall and so, in order to cut-down on the number of screws in the brick, I think I would forgo the plywood panel and just add the cleats directly to the brick using Tapcons. What are your (and others') thoughts on many Tapcons into the brick wall? Strong enough? Would they loosen over time?
Another option is to use the plywood panel and only use screws for the cleats that stop just before the brick. So, something like an 1.25" screw. Would that be strong enough?
You could put spacers so that the plywood sticks out from the brick further so you can use longer screws and use thicker plywood to make sure it is strong enough to hold the cleats up.
Nice work!!!
Too bad you don't live in GA. I would pay you to do my walls while watch and drink beer. Great job.......heck I even work for a power tool company.
Just started my french cleat wall tool holder project. Just an observation, if your tool holder is long enough to hang over the french cleat below the one is is hanging on, do you really need the support blocks? Thanks for sharing!
Correct. If it’s hanging over the cleat below then you generally don’t need the extra back support. I suggest you have it hang over the bottom cleat .5 to .75 inches to avoid breaking the tip of the cleat.
Given that I live in a humid climate with temperature extremes, would it be advisable either to paint or clear-coat the plywood and cleats?
Why the 20amp outlet? Looked like the original was 15amp,
awesome system & custom shelves - how do you like that Wen bandsaw?
Love it. Very handy and easy to replace the band. However it's not made for heavier cutting so would want to get a larger one if you plan to cut 2x4s or dense hardwood. For these more dense items it will cut them fine but the band will slightly bend, making an uneven cut if you go too fast.
спасибо бро ,что ты есть!!!
Me and my dad call it "ripping an edge" when you blunt the sharp, freshly cut edge.
Bro... you gotta tell me how you teleport like that!
Very nice video. Thank you for creating this video.
Fantastic video !!
How do you like that Wen band saw? I got their 7 1/4 track saw (with a powertech track) and absolutely love it. I want a band saw but can't afford/fit a large band saw so I was considering the Wen.
I’m seeing that SNL bit about Blue Oyster Cult in my mind - “It needs more cowbell!!!” In this case it’s French Cleat Wall. 😂
this was a great vid! looking to add a cleat wall to my garage soon...and this vid was very helpful. thanks!
What brand is your portable cutting table
What is the total distance between the bottom of one cleat to the bottom of the one above it, sine each cleat is based on a 4in board cut at 45 degrees? Looks like you have a quarter of an inch or so of space when you hang an object from the wall.
Very informative and interesting video! Keep up the good work!
I don't know were else to ask this question,does a UA-camr know when a person has subscribed to their channel,like wat video they were watching?
What is that track you used with the circular saw for the straight cuts?
Anything to replace this french cleat? it looks a waste of space and material
Nice job
Part II?
Did you replace a 15A outlet with a 20A one? I guess it looks like maybe the wire is 12ga but hard to tell.
Good catch. I've mentioned it on other posts and you are correct that I switched a 15 for a 20 amp outlet. You are also correct in that this is a 12ga wire on a 20 amp circuit so that change was intentional. Anyone reading this, you need to check the breaker box and make sure you don't put a 20 amp outlet on a 15 amp circuit. The opposite, 15 or 20 amp outlet on a 20 amp circuit, is generally up to code.
At 4:42 minutes, u show the space u use between them, is it 2.5 inch wide?? Or more??
The cleat itself is 1.5 inches on the shorter side and 2.25 on the longer side
The gap between my cleats is 2.25 inches, but you could go 2.5 inches or more.
From base of first cleat to top of second cleat is 6.75 inches.
Base of first cleat to the base of second cleat is 4.5 inches.
Thanks for the question.
@@beefmaster_james this is so helpful answer, thx a lot
use lexan for visibility
Thanks so much for sharing this !
what size pipe for the glue tubes? tia
do they make dits for these yet?