Stay tuned for the driving impressions. Spoiler alert, it makes a bigger difference than you'd think! --Subscribe to Blackout Tinting here: bit.ly/3gatFCe --Attack Blue Air Filter video: ua-cam.com/video/ql4eQ8JdmLc/v-deo.html
Any difference to throttle response? Still not happy with mine though the attack blue did help. Thinking of going with a ported throttle body or maybe the Soler throttle controller. Not sure what’d be better. P.S. Is it bad that I knew when you were taking that intake to Blackout it was for Xpel on the little window 😆?
lol no it's not bad, anyone who knows me should know by now I XPEL everything! Honestly, the intake helped MASSIVELY with throttle response it's the weirdest thing. I'm going to talk about it in the next video but it basically made starting out in any gear a lot smoother. You can definitely tell the car can breathe better.
Great video and clean install! About 10 years ago I had a conversation with my high school buddy who went onto be an aerospace engineer. I had asked him about screens that might be installed in intakes, of at the inlet of MAF sensors, etc. He explained that those screens usually help create small eddies of wind current that smooth out the air flow, which helps the sensors get better averages. My guess, based on his explanation, is that your new air filter does a better job of providing smooth air flow than the stock one that had the screen in it. But, who knows for sure. LOL.
Justin the screen straightens the air out to the maf sensor. Also the stingray isn't a forced induction motor and doesn't require any better filter then maybe a BMS filter.
It's definitely interesting that the new intake doesn't have that screen then. There's definitely a reason why the intake doesn't add any extra power for the stingray and you're right if I had to guess it's because it's not forced induction.
@@HorsePowerObsessed government requirements to have the screens also why some vette have DOD for gas mileage. My right foot determines gas mileage for me
@@HorsePowerObsessed yea my heads cam setup go rid of all that. Those dod lifters fail alot of times if not used enough. On my setup i still get 30mpg on expressway and still great road manners n fun starts at 3500👍👍
Finally someone testing out these intakes, I just ordered mine today, I dont believe the hype of all the other intakes $600+ I think with this bigger box and filter you've eliminated restriction on the intake side, I'd say your good for 800 rwhp if not more before you reach any bottlenecks. 103mm throttle body, 5 inch intake, ported blower, only if your planning 1000 rwhp + 😄
The driveability difference is huge. Something I've never actually experienced from another cold air intake install in my life. I think this thing is really built to suit this car and that makes all the difference.
Justin, your videos are amazing brother. I recently bought a 2019 C7 Corvette Z06 and I’m taking your videos into careful consideration on what I do to mod my vehicle. My direct question to you is what is a safer and more effective mod. Is it the one in this particular video or the blue air filter from one of your other videos? My second question is this new air intake a GM authentic part? If so, what is the part number and cost? My main concern is I don’t want any engine issues or check engine lights and I don’t wanna deal with any type of tuning.
Honestly, the best bang for your buck is going to still be the attack blue air filter. The cost of the GM performance intake is a lot higher with minimal additional gains over the Attack Blue. You can grab one here for the C7 Corvette: www.horsepowerobsessed.com/collections/2014-2019-corvette/products/attack-blue-air-filter-1
Sometimes it's not all about the HP gains, it's all about the looks that matter. If I had a ZR1, I think this would have been one of my first, if not the first mod I would have done. Extra HP? Sure, I'll take it! But it's the looks , no codes thrown and no tune necessary that I like! It's a Trifecta Win, WITH the possibility of it being a Quadfecta (my word) Win. 😉 I applaud your instructural videos and the details that you provide. You make it look like even a Dinosaur can do it. Now, how about and unsolicited accent-mod idea? Why not red accent the Corvette lettering and the four ribs on the intake plenum? That's it. Man of Few Words is out. Save the Wave🙋🏼♂️
Thanks, Peter! I would do the red accent if you'd ever see it but the carbon fiber cover completely hides it. The intake, much to my surprise, has added a big boost in driveability. I don't really feel the 17 extra horsepower but it allows a lot more air in apparently because the shift from 1st to 2nd gear is so much smoother.
Okay, better late than never. I just came in from "tearing it up" on the John Deere. That's how I do my best thinking. 🤦🏼♂️ Anyway, you are correct in that the CF cover does cover the plenum. My bad. But, yep, always a "but." BUT, if you design a prop rod to "prop" the CF cover up, like for a car show display, people would see it. Plus, wouldn't you sleep better at night knowing that you probably have the only ZR1 with a Red Accent Engine Design Package? Maybe Blackout Tinting could do a heat resistant red lettering & rib kit and you could do the marketing for it. We could make a fortune! Oklay, okay. You guys could make a fortune. 😉 I'll just have to rest easy 😴 knowing I did a good deed for making the ZR1's in the world LOOK FRIGG'N AMAZING! 🤭 Have a good rest of the week. I'm now going back out to finish my mowing under the stars. Luckily I installed a pair of F15 landing lights on it. They light up a whole half-acre at a time. Vrooom, I'm outta here!🏎
a back fire screen..if the motor ever back fired for whatever reason the screen keeps the filter from catching on fire and burning down the car. the after market filter is a back fire resistant (flame resistant) and don't need the screen, no screen equals more air flow.
Great vid. Check out Geigers Z06 break 7:00 minutes on the Nurburgring. The ZR1 prepped correctly would destroy the Nurburgring times. Please research the video from Geiger in You tube.
This was one of the first mods I did to mine..really it the first thing i have always done to all of my cars lol and yes its worth it I went with afe though 😜 I tell you something though I noticed the biggest difference when I changed it out on my 2019 yukon Denali it also has the LT1 engine in it zoom zoom lol
It's usually the same for me but I've never really noticed a big difference by changing it out. This is the first time that the difference was insanely noticeable.
@@HorsePowerObsessed i also went with a ported and polished throttle body and afe makes a Silver Bullet Throttle Body Spacer that helps out too check it out afepower.com/afe-power-46-34011-silver-bullet-throttle-body-spacer
$89 Burger drop in filter should work just as well. Do yourself a favor and buy one. No different than the one above, minus the Jake box. Definitely better throttle response, and a little louder from both exhaust and the blower.
I had one, I also had an attack blue air filter and I've tried all kind of different intakes. None of them have improved drivability like this one did. I have a few brand new air filters I'll be dyno-ing soon.
@@HorsePowerObsessed I was always under the impression that one is literally just as good as the other. I will take that advice and give it a try. I will say, the biggest benefit for me was how much cooler the LT4 was after installing. Drove a hundred miles in 90° heat with at least 60% humidity and the temp gauge was below 200. Not much but it was. GM really does it's buyers a disservice by not putting a better filter in. But that's GM doing GM things.... appreciate the response and keep up the good work.
Thank you. I appreciate the support. For me it's always been one or the other. The drop in is the cheaper/easier way to gain a few ponies and keep maintenance a little easier but the real gain is always with a full setup. It's more expensive and the gains might not be much more than a drop in so it's always a personal preference.
Hey J...nothing from afe for the Batmobile ?? Thought they had one. Can't wait to see the results. Good job on the install btw. Gonna stay tuned bro. Thx man.
Nicely done professional video... But I did not see a link for the product that you installed (air intake with Jake logo). I like how you used the XPEL for the window, do you use it on your touch screen or does it mess up the touch effect?
Thank you. Air intake part number 84689752. You can find it here: www.shopchevyparts.com/performance/2019-corvette-stingray-performance-air-intake-lt1-lt4-zr1-lt5-engine-corvette-jake-logo/84689752-p-92300480.html. I do use XPEL on my touch screen but it's a special version called XPEL RX. It has antimicrobial attributes as well as the same impact resistance and self healing technology the normal XPEL PPF has. If you're interested in getting some pre-cut for your C7 shoot me an email at Horse.Power.Obsessed@gmail.com.
Hey Justin!! ANOTHER great and informative video!! What percentage window tinting did you use for your red Z06 and also your current ZR1?? Thank you... Bob
seems like a lot of money and time just for a better looking intake, the only power difference you are going to feel is in your head,better intake sucking sound and you,ll hear the whine of the SC a little more,without a tune its 99.9% window dressing,but hey to each his own if you have the $ to do it,and if you own a C7 ZO6 you can afford it!.lol btw very cool looking intake!
Straight from GM, this intake gains 17HP on a dyno with the ZR1 and I definitely notice smoother shifts from 1st to 2nd gear where the stock airbox felt like it was choking the engine. Definitely not in my head. It is a bit expensive, but worth it. These aren't wild claims by someone trying to sell you snake oil, this is straight from GM tested on their cars.
I added an aFe to my C7, according to my (most excellent) mechanic he said maybe 5 - 10 HP in the upper range. The most I've gotten is a little better noise and maybe a little quicker throttle response (and it looks cool). A lot more expensive than the ones I added to my C5, C6's....
This is the same I've heard which is why I was so surprised with the GM performance one. I could literally feel the difference in driveability and that's something completely new to me.
Thank you for the Video, would you say that both Filters are the same size and interchangeable ? Also any Video with the Intake Sound under acceleration ? Regards.
You're welcome. The filters are not interchangeable, the GM performance filter is bigger, both wide and deeper. It has a more free flowing media to it as well which the ZR1 especially benefits from. No other videos about this but I will be making another soon talking about some more details such as driveability differences, etc. Stay tuned for that.
Any before and after or just your opinion on a aftermarket bolt-on "feels better"? You stated data would be provided later. I can't find a video or link to any.
@@HorsePowerObsessed I have been down a rabbit hole trying to find data on two different things. #1. Dyno HP/TQ #s on a box stock 2017 C7, followed up with a optimized tune only run, same day, same dyno. #2. Back to back dyno runs, with stock, then aftermarket CAI or K@N type replace air filters. I'm concluding the later has been done and the data doesn't support positive results for the filter companies. Thank you for the polite response when my initial comment lacked a little respect.
No problem at all. I have baseline numbers for the car already with everything stock but I still need to run it with the GM performance intake. GM claiming 17 extra with the ZR1 is a little more substantial than an aftermarket air filter claim so I'm pretty confident it will make 17 or so extra but we'll see!
Hi Justin I ended up installing the Attack Blue engin air filter. There was no info if the GM mod you just had any improvement on a C7 GS. Do you know if there was any hp/ torque gain for a GS?
The Attack Blue filter is fantastic for the stock intake box. It does magical things, but I wanted to try something different. I don't have numbers yet but I will soon.
I didn't! Sorry I will link it now. Part number 84689752. You can find it here: www.shopchevyparts.com/performance/2019-corvette-stingray-performance-air-intake-lt1-lt4-zr1-lt5-engine-corvette-jake-logo/84689752-p-92300480.html
Sorry I will link it now. Part number 84689752. You can find it here: www.shopchevyparts.com/performance/2019-corvette-stingray-performance-air-intake-lt1-lt4-zr1-lt5-engine-corvette-jake-logo/84689752-p-92300480.html
@@HorsePowerObsessed i went through the same thing here no dealership would do it then i found a tire place and they ruined one of my rims a nd they had to buy me another one so be careful. i finally found a place called tire time they specialize in the bro's rims like ridding on 27" if you no what i mean . No chevy dealership would do it
How many filters are u going to try man? Jus get a car with all that you spent. You have had stock,bms, attack blue and now this. Jus get a tune and a 103 throttle body and your set
lol I'm looking for that perfect match and I think I found it here. I'm trying to get numbers for all the filters out there so people know exactly what they are going to get.
Stay tuned for the driving impressions. Spoiler alert, it makes a bigger difference than you'd think! --Subscribe to Blackout Tinting here: bit.ly/3gatFCe --Attack Blue Air Filter video: ua-cam.com/video/ql4eQ8JdmLc/v-deo.html
Any difference to throttle response? Still not happy with mine though the attack blue did help. Thinking of going with a ported throttle body or maybe the Soler throttle controller. Not sure what’d be better. P.S. Is it bad that I knew when you were taking that intake to Blackout it was for Xpel on the little window 😆?
lol no it's not bad, anyone who knows me should know by now I XPEL everything! Honestly, the intake helped MASSIVELY with throttle response it's the weirdest thing. I'm going to talk about it in the next video but it basically made starting out in any gear a lot smoother. You can definitely tell the car can breathe better.
Your in corvetteblogger bro
@@johnd5805 I am?
@@HorsePowerObsessed www.corvetteblogger.com/2020/07/08/audio-corvette-youtuber-horsepower-obsessed-featured-this-week-on-the-corvette-today-podcast/?
Great video and clean install! About 10 years ago I had a conversation with my high school buddy who went onto be an aerospace engineer. I had asked him about screens that might be installed in intakes, of at the inlet of MAF sensors, etc. He explained that those screens usually help create small eddies of wind current that smooth out the air flow, which helps the sensors get better averages. My guess, based on his explanation, is that your new air filter does a better job of providing smooth air flow than the stock one that had the screen in it. But, who knows for sure. LOL.
That was my deduction as well but since I am not an engineer I can never be sure of these things lol.
Josh is the man, Great video Justin 👌
Thank you! He's definitely the man!
Justin the screen straightens the air out to the maf sensor. Also the stingray isn't a forced induction motor and doesn't require any better filter then maybe a BMS filter.
It's definitely interesting that the new intake doesn't have that screen then. There's definitely a reason why the intake doesn't add any extra power for the stingray and you're right if I had to guess it's because it's not forced induction.
@@HorsePowerObsessed government requirements to have the screens also why some vette have DOD for gas mileage. My right foot determines gas mileage for me
Yeah I'm not a big fan of the DOD and I'm glad the ZR1 dropped it.
@@HorsePowerObsessed yea my heads cam setup go rid of all that. Those dod lifters fail alot of times if not used enough. On my setup i still get 30mpg on expressway and still great road manners n fun starts at 3500👍👍
Finally someone testing out these intakes, I just ordered mine today, I dont believe the hype of all the other intakes $600+ I think with this bigger box and filter you've eliminated restriction on the intake side, I'd say your good for 800 rwhp if not more before you reach any bottlenecks. 103mm throttle body, 5 inch intake, ported blower, only if your planning 1000 rwhp + 😄
The driveability difference is huge. Something I've never actually experienced from another cold air intake install in my life. I think this thing is really built to suit this car and that makes all the difference.
They just recalled some of the Harbor Freight jack stands that replaced the ones that were recalled before.
I had to switch mine out already and now I have to do it again! 😬
@@HorsePowerObsessed I gave up on HF jack stands after the first recall. My life is way more important than saving a few dollars
I may have to do the same... This is getting a little ridiculous now.
It’s all about that Cordes 5” intake, I’m gonna def throw it on my Z06 once I get a bigger tb
If you're tuning you're right! Without a tune this is the best one you can get.
Justin, your videos are amazing brother. I recently bought a 2019 C7 Corvette Z06 and I’m taking your videos into careful consideration on what I do to mod my vehicle. My direct question to you is what is a safer and more effective mod. Is it the one in this particular video or the blue air filter from one of your other videos? My second question is this new air intake a GM authentic part? If so, what is the part number and cost? My main concern is I don’t want any engine issues or check engine lights and I don’t wanna deal with any type of tuning.
Honestly, the best bang for your buck is going to still be the attack blue air filter. The cost of the GM performance intake is a lot higher with minimal additional gains over the Attack Blue. You can grab one here for the C7 Corvette: www.horsepowerobsessed.com/collections/2014-2019-corvette/products/attack-blue-air-filter-1
Hi Justin, another great install video! Thanks!
Thank YOU!
Sometimes it's not all about the HP gains, it's all about the looks that matter. If I had a ZR1, I think this would have been one of my first, if not the first mod I would have done. Extra HP? Sure, I'll take it! But it's the looks , no codes thrown and no tune necessary that I like! It's a Trifecta Win, WITH the possibility of it being a Quadfecta (my word) Win. 😉 I applaud your instructural videos and the details that you provide. You make it look like even a Dinosaur can do it.
Now, how about and unsolicited accent-mod idea? Why not red accent the Corvette lettering and the four ribs on the intake plenum?
That's it. Man of Few Words is out. Save the Wave🙋🏼♂️
Thanks, Peter! I would do the red accent if you'd ever see it but the carbon fiber cover completely hides it. The intake, much to my surprise, has added a big boost in driveability. I don't really feel the 17 extra horsepower but it allows a lot more air in apparently because the shift from 1st to 2nd gear is so much smoother.
@@HorsePowerObsessed Yes, but when the hood is open you see it. Hey, it's all in the details. 😉
Absolutely agree! 😎
Okay, better late than never. I just came in from "tearing it up" on the John Deere. That's how I do my best thinking. 🤦🏼♂️ Anyway, you are correct in that the CF cover does cover the plenum. My bad. But, yep, always a "but." BUT, if you design a prop rod to "prop" the CF cover up, like for a car show display, people would see it. Plus, wouldn't you sleep better at night knowing that you probably have the only ZR1 with a Red Accent Engine Design Package? Maybe Blackout Tinting could do a heat resistant red lettering & rib kit and you could do the marketing for it. We could make a fortune! Oklay, okay. You guys could make a fortune. 😉 I'll just have to rest easy 😴 knowing I did a good deed for making the ZR1's in the world LOOK FRIGG'N AMAZING! 🤭 Have a good rest of the week. I'm now going back out to finish my mowing under the stars. Luckily I installed a pair of F15 landing lights on it. They light up a whole half-acre at a time. Vrooom, I'm outta here!🏎
I've actually seen something similar that props up the carbon fiber cover. I'm not sure if I'd want to go through all that work though lol
a back fire screen..if the motor ever back fired for whatever reason the screen keeps the filter from catching on fire and burning down the car. the after market filter is a back fire resistant (flame resistant) and don't need the screen, no screen equals more air flow.
Great vid. Check out Geigers Z06 break 7:00 minutes on the Nurburgring. The ZR1 prepped correctly would destroy the Nurburgring times. Please research the video from Geiger in You tube.
Wow! That's crazy! These cars are such beasts!
This was one of the first mods I did to mine..really it the first thing i have always done to all of my cars lol and yes its worth it I went with afe though 😜 I tell you something though I noticed the biggest difference when I changed it out on my 2019 yukon Denali it also has the LT1 engine in it zoom zoom lol
It's usually the same for me but I've never really noticed a big difference by changing it out. This is the first time that the difference was insanely noticeable.
@@HorsePowerObsessed i also went with a ported and polished throttle body and afe makes a Silver Bullet Throttle Body Spacer that helps out too check it out
afepower.com/afe-power-46-34011-silver-bullet-throttle-body-spacer
$89 Burger drop in filter should work just as well. Do yourself a favor and buy one. No different than the one above, minus the Jake box. Definitely better throttle response, and a little louder from both exhaust and the blower.
I had one, I also had an attack blue air filter and I've tried all kind of different intakes. None of them have improved drivability like this one did. I have a few brand new air filters I'll be dyno-ing soon.
@@HorsePowerObsessed I was always under the impression that one is literally just as good as the other. I will take that advice and give it a try. I will say, the biggest benefit for me was how much cooler the LT4 was after installing. Drove a hundred miles in 90° heat with at least 60% humidity and the temp gauge was below 200. Not much but it was. GM really does it's buyers a disservice by not putting a better filter in. But that's GM doing GM things.... appreciate the response and keep up the good work.
Thank you. I appreciate the support. For me it's always been one or the other. The drop in is the cheaper/easier way to gain a few ponies and keep maintenance a little easier but the real gain is always with a full setup. It's more expensive and the gains might not be much more than a drop in so it's always a personal preference.
Hey J...nothing from afe for the Batmobile ?? Thought they had one. Can't wait to see the results. Good job on the install btw. Gonna stay tuned bro. Thx man.
Thanks, JT! Nothing from anyone else for the ZR1 other than GM.
Those snaps are very satisfying... what'll Justin XPEL next!?!
Hmm! I wonder! 🤔
@@HorsePowerObsessed Bring your sleeping bag.
Isn't it still there? I left one a few weeks ago.
The body XPEL would be interesting. You’d probably only have to shower like once a year or something. No need for a video on it though!
Lol yeah I'm not really sure how it would work yet... 🤔
Might get this for my 19 Z06. Heard that if I pay Chevy to install that I will retain my full factory warranty
It makes a huge difference. I plan on filming an update video soon about it.
Nicely done professional video... But I did not see a link for the product that you installed (air intake with Jake logo). I like how you used the XPEL for the window, do you use it on your touch screen or does it mess up the touch effect?
Thank you. Air intake part number 84689752. You can find it here: www.shopchevyparts.com/performance/2019-corvette-stingray-performance-air-intake-lt1-lt4-zr1-lt5-engine-corvette-jake-logo/84689752-p-92300480.html. I do use XPEL on my touch screen but it's a special version called XPEL RX. It has antimicrobial attributes as well as the same impact resistance and self healing technology the normal XPEL PPF has. If you're interested in getting some pre-cut for your C7 shoot me an email at Horse.Power.Obsessed@gmail.com.
Hey Justin!! ANOTHER great and informative video!! What percentage window tinting did you use for your red Z06 and also your current ZR1?? Thank you... Bob
Thank you! I appreciate the support. I have 20% on all my cars/truck.
seems like a lot of money and time just for a better looking intake, the only power difference you are going to feel is in your head,better intake sucking sound and you,ll hear the whine of the SC a little more,without a tune its 99.9% window dressing,but hey to each his own if you have the $ to do it,and if you own a C7 ZO6 you can afford it!.lol btw very cool looking intake!
Straight from GM, this intake gains 17HP on a dyno with the ZR1 and I definitely notice smoother shifts from 1st to 2nd gear where the stock airbox felt like it was choking the engine. Definitely not in my head. It is a bit expensive, but worth it. These aren't wild claims by someone trying to sell you snake oil, this is straight from GM tested on their cars.
I added an aFe to my C7, according to my (most excellent) mechanic he said maybe 5 - 10 HP in the upper range. The most I've gotten is a little better noise and maybe a little quicker throttle response (and it looks cool). A lot more expensive than the ones I added to my C5, C6's....
This is the same I've heard which is why I was so surprised with the GM performance one. I could literally feel the difference in driveability and that's something completely new to me.
I got 8 more horses on my c7 and quicker throttle response
@@HorsePowerObsessed So i won't feel any difference at all even if i get the bigger one on the C7 stingray or G/S?
even just sound or feeling?
I got 8 more horses on my c7 and quicker throttle response
You won't get any extra horsepower but there still will be a difference in drivability due to the extra space for air.
Will there be any benefits adding this to the grandsport?
Horsepower wise, GM says no but there is definitely driveability that gets added regardless of trim.
The only C8 on Dragy has improved its 0-60 time from 4.14 to 4.12 secs! It's up to the 94th fastest Chevy. Sheeze, the marketing lies.
Interesting!
Dragy is bullshit in my opinion. Many cars underperforming according to that device
When does this new filter needs replacement and can it be cleaned or does it need to be replaced with a new one? I have 13000 miles on my filter.
Hi excellent vid, looking for dyno proof. Froggy
Coming soon! The driveability difference is real, though. 2nd gear feels totally different and much less jerky.
Can you / will you use the Attack Blue Air filter in the GM Airbox?
No you can't. It's designed for the stock airbox so it's kind of one or the other. One is a lot cheaper than the other as well!
What did you end up doing with that torch red waterfall interior compartment? I ask as a C7 Z06 torch red owner.
I ended up selling it. I just wasn't in love with it.
@@HorsePowerObsessed thanks for the thoughtful and prompt reply, my friend. We enjoy the content! Best.
Thank you!
Thank you for the Video, would you say that both Filters are the same size and interchangeable ? Also any Video with the Intake Sound under acceleration ? Regards.
You're welcome. The filters are not interchangeable, the GM performance filter is bigger, both wide and deeper. It has a more free flowing media to it as well which the ZR1 especially benefits from. No other videos about this but I will be making another soon talking about some more details such as driveability differences, etc. Stay tuned for that.
@@HorsePowerObsessed thank you. Looking forward to the new Video.
You're welcome!
What about z06 what filter is best for torque and power
I would say the GM performance intake or the aFe intake.
I just got afe waiting to come in
Any before and after or just your opinion on a aftermarket bolt-on "feels better"? You stated data would be provided later. I can't find a video or link to any.
I haven't gotten it on a dyno yet but there is a huge drivability improvement even if power isn't added.
@@HorsePowerObsessed I have been down a rabbit hole trying to find data on two different things. #1. Dyno HP/TQ #s on a box stock 2017 C7, followed up with a optimized tune only run, same day, same dyno. #2. Back to back dyno runs, with stock, then aftermarket CAI or K@N type replace air filters. I'm concluding the later has been done and the data doesn't support positive results for the filter companies. Thank you for the polite response when my initial comment lacked a little respect.
No problem at all. I have baseline numbers for the car already with everything stock but I still need to run it with the GM performance intake. GM claiming 17 extra with the ZR1 is a little more substantial than an aftermarket air filter claim so I'm pretty confident it will make 17 or so extra but we'll see!
@@HorsePowerObsessed I wonder how your baseline numbers would differ from your last dyno session?
I will chose a day with similar temperature but other than that I don't know.
I'm curious as to why you didn't purchase the AFE Momentum Cold Air Intake System for your Corvette as they advertise up to a 46 hp gain.
There's a few reasons, but the 46hp gain is an absolute gross overestimate. If it is 10hp I'd be surprised, and it won't fit the ZR1.
I see you took out your ACS waterfall? How are you liking it? I have one as well. I feel like mine creaks a bit.
It's out for detailing/ceramic coating.
Hi Justin I ended up installing the Attack Blue engin air filter. There was no info if the GM mod you just had any improvement on a C7 GS. Do you know if there was any hp/ torque gain for a GS?
The Attack Blue filter is fantastic for the stock intake box. It does magical things, but I wanted to try something different. I don't have numbers yet but I will soon.
@@HorsePowerObsessed For sure.
👍👍
Why did you go oem intake nd not afe? Looking what to buy
The afe unit won't fit the ZR1. The GM performance intake is the only option for the ZR1 without tuning.
Didn't you used to have a trx?
I still do. This is an older video.
Nice vid!! Does it throw a code or make engine lite come on??
No sir. Hands down the best air intake I've ever installed.
I'm not seeing the link to the Air Intake Box. Did you provide it?
I didn't! Sorry I will link it now. Part number 84689752. You can find it here: www.shopchevyparts.com/performance/2019-corvette-stingray-performance-air-intake-lt1-lt4-zr1-lt5-engine-corvette-jake-logo/84689752-p-92300480.html
So I am debating on getting a Z06 never owned brand X but always said I would own a Vette. How is it living with the vette?
It's unreal. Literally a dream come true. It's such a great car.
You will love it. Had a C4. C5. And a C6. C7 next. The sound of that engine underneath all that fiberglass......a true experience.
Hey bro im a big guy like you almost 300lbs my question is, are the competition seats comfortable? (as a daily driver car)
I'm not 300 pounds, but yes, the seats are perfectly comfortable for me.
Have you put the attack blue filter in this upgraded airbox
They don’t make one for the new air box yet.
I wished they would. Hated giving up the extra filtration. Looks like the lip around the top just needs to thinner. Hope they come back to it soon.
No hp for stingray or gs.. guess I’ll use my money elsewhere..and keep the stock
Hey can you tell me whay kind and where did you get your rims from.. Sorry to go off beat... Lol....
Hey no problem. These are stock ZR1 wheels.
Looking for air box link in description
Thanks
Sorry I will link it now. Part number 84689752. You can find it here: www.shopchevyparts.com/performance/2019-corvette-stingray-performance-air-intake-lt1-lt4-zr1-lt5-engine-corvette-jake-logo/84689752-p-92300480.html
Thanks boss. And the discount code? ZR1 took all my money!
I wish I had one. No sponsorship here. I paid full price for it.
I wonder if this voids the warranty...?
It does not. It’s a GM part that is specifically said to not void warranty by GM.
Still waiting for the before and after videos of the exhaust
My car has been laid up waiting for new tires... 🤦♂️
@@HorsePowerObsessed i hear ya! getting the cup2's?
Yes sir. I already got the tires I'm just having trouble finding somebody who can mount them...
@@HorsePowerObsessed i went through the same thing here no dealership would do it then i found a tire place and they ruined one of my rims a nd they had to buy me another one so be careful. i finally found a place called tire time they specialize in the bro's rims like ridding on 27" if you no what i mean . No chevy dealership would do it
If there’s no gain for my stingray, no sense buying it
Is that a cold air intake and what makes it a cold air intake?
Yes. It pulls air from the fenderwell instead of the hot engine bay.
17 horsepahr.
🤣🤣🤣
How many filters are u going to try man? Jus get a car with all that you spent. You have had stock,bms, attack blue and now this. Jus get a tune and a 103 throttle body and your set
lol I'm looking for that perfect match and I think I found it here. I'm trying to get numbers for all the filters out there so people know exactly what they are going to get.
OBSSESSIVE-COMPULSIVE.DISSORDER..ON PLASTIC-COATING??