That's very well done. But an easier solution would be to just buy a used Samsung Galaxy Tab Active3. It's a rugged 8" tablet with a high resolution designed to be dust, vibration and waterproof, along with a SIM card for data, physical buttons for use with gloves, a bright screen to be used outdoors, a faster processor that typical mid sized Android tablets and a touchscreen that can be used with regular gloves. It can be powered hard wired without a battery if desired and several companies such as Brodit and RAM make mounts for it.
The setup looks great, although the Lenovo display can not be seen under sunlight , look at the Tripltek tablet , it looks sleek and at the same time it has 1300 nits
The tablet model is lenovo tab m7. tools necessary; soldering iron, heat gun, screwdriver, etc. I'm using iphone therefore I don't have chance to connect as it is an android tablet.
Hola saludos desde SAN JUAN ARGENTINA, me encanta tu trabajo ,esa tablet le queda genial a tu moto ,tu moto es una belleza ,exitos y gracias por compartir tu contenido 👏👏👏👏👌🤗🤗🤗🤗🤗🤗
That is awsome, how is the longevity on the 3d printed parts? I want to put a GPS bar on my super tenere, and I was thinking about making it 3d printed, but I'm worried about longevity of the piece
Hi, thank you for this video, i love it so much, i decided to make it for my bike too. How did you connect tablet to the bike? What is inside the connector at 1:19? So must you wait for tablet start every time you start motorcycle ? Thanks
There are 4 wires inside the socket. 2 wires for power. 2 wires for power. I converted 12 volts to 4.2 volts from the engine's battery and connected it to the tablet like a battery. A small tip, the small circuit on the battery should be removed and used.yes, every time I start the engine, if I want to turn on the tablet, I press and hold the power button and turn it on.
How did you make it waterproof? Doesn't water seep in between the front frame piece and the display? How did you fix the back piece to the front frame piece? I mean, did you glue it? What type of glue?
To make it waterproof I used T-7000 glue to fix front piece and tablet screen.I printed these pieces with ABS thats why the best glue for abs is %99,9 Acetone.
@@nzferby Thanks. The 3D model is a bit large for the printer at the service I normally use. Trying to find a new place. My friend has a Tab 7 lying around and is ready to give me (in return for a few beers). So, really hopeful 😄. BTW, how is the quality of the GPS fix?
It´s only 350 nits, i have problem with my Samsung FE20 and that have 823 nits, and i have trouble to se in sunlight, but it´s seems ok on your video.hmm
BUTTON : motowoks.com/products/4-pin-cable-button-for-850c I removed the battery to avoid problems under the sun. i canceled the sd card to make it waterproof..👍
Yeah ok. Thanks for the link.. In the middle of printing one for my Africa Twin. Modded the model a bit to give more offest from the mounting point and changed the T7 to AT..:)
@@nzferby Thank you. I'm making the same one for myself. The model has already been printed on a 3D printer. Now I'm looking for a tablet on the secondary market.
Thats very well done! .. looks so integrated. 👏🏽
This is the type of stuff I love to see on youtube.
Thank you very much for your comment.
Hello this is so awesome can I use it for a galaxy active tab 3 in my africa twin?
I love how the screen and the original dashboard are flush!😍
That's very well done. But an easier solution would be to just buy a used Samsung Galaxy Tab Active3. It's a rugged 8" tablet with a high resolution designed to be dust, vibration and waterproof, along with a SIM card for data, physical buttons for use with gloves, a bright screen to be used outdoors, a faster processor that typical mid sized Android tablets and a touchscreen that can be used with regular gloves. It can be powered hard wired without a battery if desired and several companies such as Brodit and RAM make mounts for it.
8" is too big for motorcycle, 7" is the best size - not too small, not too big
The setup looks great, although the Lenovo display can not be seen under sunlight , look at the Tripltek tablet , it looks sleek and at the same time it has 1300 nits
Looks great!
Is it also BT connected with the bike?
Müthiş çok güzel olmuş tam şimdi seyehat odakli t7 gibi olmuş işte birde tubless jant lar olsa miss gibi olacak
Nice 👍
I just finished my rally tower, filming a summary today 🤪
Can't wait to see it. 👍
Wonderful, could you advice which model and what tools we need for apply? Also Abt gps, pair by phone?
The tablet model is lenovo tab m7. tools necessary; soldering iron, heat gun, screwdriver, etc. I'm using iphone therefore I don't have chance to connect as it is an android tablet.
oem style, very well done!
witch software did you use?
Yamaha'ya satın bu işçiliği, rally kit'e dahil etsinler:)) Elinize sağlık, harika olmuş.
Tesekkurler.👍
Yamaha, please, bring the Ténéré 700 to Brazil.
Hola saludos desde SAN JUAN ARGENTINA, me encanta tu trabajo ,esa tablet le queda genial a tu moto ,tu moto es una belleza ,exitos y gracias por compartir tu contenido 👏👏👏👏👌🤗🤗🤗🤗🤗🤗
gracias❤
How did you wire the volume buttons? Do you really feel it is useful to have them if you don't want to listen to music from it?
That is awsome, how is the longevity on the 3d printed parts? I want to put a GPS bar on my super tenere, and I was thinking about making it 3d printed, but I'm worried about longevity of the piece
Abs plastic life is very good I have been using it for 9 months without any problems👍
Hey mate I printed this and thank you. What glue did you use to assemble it?
I printed abs so i used 100% acetone to glue it.
Looks amazing, how is it connected to the bike?
Here is the link of the 3d parts. www.thingiverse.com/thing:5276565/files
man, would love to see this done with a galaxy A7lite due to the 8.7" screen!
I think you can scale print files according to samsung👍
Hi, thank you for this video, i love it so much, i decided to make it for my bike too. How did you connect tablet to the bike? What is inside the connector at 1:19? So must you wait for tablet start every time you start motorcycle ? Thanks
There are 4 wires inside the socket. 2 wires for power. 2 wires for power. I converted 12 volts to 4.2 volts from the engine's battery and connected it to the tablet like a battery. A small tip, the small circuit on the battery should be removed and used.yes, every time I start the engine, if I want to turn on the tablet, I press and hold the power button and turn it on.
How is the Lenovo M7 Tab working out for a display? Have you had an issue connecting with apps?
How did you make it waterproof? Doesn't water seep in between the front frame piece and the display? How did you fix the back piece to the front frame piece? I mean, did you glue it? What type of glue?
To make it waterproof I used T-7000 glue to fix front piece and tablet screen.I printed these pieces with ABS thats why the best glue for abs is %99,9 Acetone.
@@nzferby Thanks. The 3D model is a bit large for the printer at the service I normally use. Trying to find a new place. My friend has a Tab 7 lying around and is ready to give me (in return for a few beers). So, really hopeful 😄. BTW, how is the quality of the GPS fix?
trying to may the Drive Mode Dashboard 2do turn by turn am I missing something ?
How does it connect to the bike’s system, like speed, rpm?
wifi or bt obd 2 with yamaha connector👍
Como alimentas el joystic, a un USB de la moto, cable 4pines?
great job broo
Hayran kaldım süper olmuş
Thanks bro. 😃
Where did you get the push button for the bars?
It is an e-bike push button controler.
which which software on Android are you viewing the data from OBD2 bluetooth module?
"car scanner"
Very well done👍 Do the Lenovo work ok with the dmd app?
No problem works fine 👍
Thank you for the vídeo and the stl files
Can I connect my phone to tablet and use android auto?
Hello. Have you made the controller? I'm working on that but I am having some issues to work.
No i didnt make, only made on\off button😅
Where can ı buy that button nicely done ✅ keep posting man
Thanks man, motowoks.com/products/4-pin-cable-button-for-850c
Abi maşallah eline sağlık çok güzel olmuş
Teşekkürler 🙏❤️
Hello
Did you totally remove the tablet battery
And use motorcycle battery with 12v to 5v converter to run the tablet
yess,i did exactly that👍No problem works great.
It´s only 350 nits, i have problem with my Samsung FE20 and that have 823 nits, and i have trouble to se in sunlight, but it´s seems ok on your video.hmm
what's the switch pls
It is a simple ebike switch.
Hello ,Which plastic filament do you use?
ABS
@@nzferby How many minutes does it take to print?
@nzferby Very cool thank you
@@vilasith88 3-4 hours..
how did you connect to the bike? for the 12v?
i use 12 to 5 volt converter.
What about the handle bar button.. And why remove the battery? Did you loose the sdcard slot?
BUTTON : motowoks.com/products/4-pin-cable-button-for-850c I removed the battery to avoid problems under the sun. i canceled the sd card to make it waterproof..👍
Yeah ok. Thanks for the link.. In the middle of printing one for my Africa Twin. Modded the model a bit to give more offest from the mounting point and changed the T7 to AT..:)
@@nzferby and how did you make it waterproof ?
Very good job !!!!
Hi can you put the link of the controller thanks
www.amazon.com/Vbestlife-Electric-Bicycle-Conversion-Controller/dp/B09X3DQT84
Hey mate, how did you assemble the parts, I´ve been trying to follow the video but something didn´t add up!
Perfect! Great idea! Thank you so much! /Rui
How much RAM is in the tablet 3, 2 or 1? Thank you
2gb
@@nzferby doesn't it slow down? works fine? What firmware?
@@hemingway8502 yes its a little bit slow but works fine.I changed it with a carplay 👍
@@nzferby Thank you. I'm making the same one for myself. The model has already been printed on a 3D printer. Now I'm looking for a tablet on the secondary market.
@@hemingway8502 Hope you can find a good one👍
Is that waterproof??
yes
@@nzferby whats type of tablet come from?
@@praktisijaringan 7" lenovo
🙌💯