Це відео не доступне.
Перепрошуємо.
101 Roofing - How to remove pooling water and connect Torch Down roof to drain
Вставка
- Опубліковано 16 сер 2024
- Removing ponding water by lowering the roof and cutting a channel to the drain. Connecting the Torch Down Rubber Roof to the drain. Channels are the most effective way to get water to flow from one part of the roof to a drain. Instead of installing insulation to fill low spots, cut a channel to allow water to drain out.
0:00 Big pond of water
1:15 Finding a low section of the pond
1:44 Snapping line for channel
2:09 Cutting roof open to remove material
4:18 Cutting tabs on drain away
4:41 Use angle grinder to cut into the roof
4:55 Removing insulation inside the channel
5:36 Installing Torch Down Rubber in channel
7:44 Tie Channel into the drain
this guy gives us professional roofers a bad name and look any1 watching this thats not a pro dont do this
He didn’t de granulate his cap over at all even and leaves tons of marks. Heat is to high and not consistent and neither is his bleeds that’s means
A real roofer would install a real copper drain.i don’t enderstand how peoples can be impress with your work😢😅
I am learning so much from your videos! Thank you for your incredible teaching
Dear God- someone please stop this guy !
Let us see if God hears you. God is not interested in pride and arrogant. Just talk to me it is easier. I am an idiot, at least a lot others are helped
Why not install a new drain properly?all that wet insulation under the roof will cause problems. Heat loss mold ect. You guy don't rip roofs at your company? Retrofit drain man. Them bolts you cut hold that drain together.
Bla bla bla make your own videos and show us your expertise. Everyone has his own tricks. You don't walk the way I walk or talk. I am not as smart as you are. You don't have all the facts of any job others are working on to make judgement calls. The best is learn something, and go for it.
@@FlatRoofDoctor I will. Because if your are doing good it won't be a problem.
Kirk Brady This guy is a absolute hack. I love his videos. What he did to that drain was appalling. His "fix" for it was even worse. His roofing videos are some of the most entertaining on UA-cam. I hope he makes a hundred more.
Roof on Roof Doctor!
If this is a forever thing I love it
Broke the pot,what a hack job,hurry up and throw it together before it rains.
Hi.
IS IT possible to create the channels on a TPO roof? There are a few spots on my churches roof that i want to do that with.
Thanks!
if ever a bad roofer gets sent to hell, he'll be wondering who turned up the AC
9:00 i've never seen this kind of bullshit in my life
Nice
no primer ?????
@Flat Roof Doctor you are such a hack job. You mislead the people who have no idea how to actually do roofing. They don't know any better. Been a union roofer for 15 years and 5 of those a forman. If I did any of this hack crap, I'd be fired on the spot that same day.
I was in the union 36 years, this guy wouldn’t last a day
Wow
lol
A brand new roof that looks like it was done 25 years ago. I just wise I could upload pictures so people could see what a new roof should look like. In all my time as a roofer I have never seen anybody ever put down torch by walking on it. Not using u flow dains and torching on top of plastic cement. Rolling out peel and stick base sheet without using elastico stick primer especially when going over old EPDM roof. How the he'll are you still in business? You try and put down roofer and tell the people that watch you videos that don't know anything about roofing they shouldn't trust roofer. Tell me why should the trust you. Installing new roof over rotting old roof. That's a guaranteed leak somewhere down the line as HVAC guys are always up on the roof doing maintenance. Dose screws are going to go right through the new membrane, but I know you have an excuse to tell your customer that it was the other guys that did it. So you can go back and charger your customer again for repairs and that they should back charge the other guys for the repair.
Can you please show why when I walk on it my shoes leave prints during tochdown? Is my heat too low and I am heating too much? My run out is uneven.
If you're leaving prints then it's too much heat. Look up some more videos and you'll notice how to use the torch in an "L pattern" when heating the roll down. Once you've got a good bleed at the seam keep going and don't stop!
Very good lesson sweetheart 😍
and hes a liar the black marks after he torches is because he over heated the rubber membrane. he even shows us the bottom of his shoes. he over heated it so that the rubber and granules adhered to his boots.... if u notice theres no marks in the beginning and never stepped in tar
Thank you for the video, 👍 good job , I been learning a lot from you 💪🏽✌🏼
Glad to help
Hello 👋🤝 where are you guys?? Can you come to help my house in San Francisco east Bay please ！！
Good job
do you have any videos start to finish on detailing a skylights with a 2 ply torch down app system? Applying base sheet, smooth roll & granular cap sheet?
Can't believe he calls himself the roof doctor.should be roof comedian he's work is a joke
yep thanks
Nice job. Why no base sheet tho?
my thoughts too
👍👍👍
BUTCHER!!!!! do a new retro fit
Well worth the 600 dollars
What a slack job, why did not you give customer a better drain package rather putting dirty paches over it and cover it up with messy and shaddy craftmanship.
You should have check weather before you open somebody's roof. Just saying if that helps you in future.
You lucky no one checks on you from RIMS.
I am very lucky
those AC refrigerant lines aren't insulated they will cost the owners money on wasted energy cooling the roof..
It's just unbelievable how stupid some rooftops are.
Insane engineering.
ok
Could u just heat the hole up and it would melt in ,without cutting the tabs i mean
Or just install a drian properly and no issues. I would not leave that drain temporarily over night.
@@kirkbrady2497 but what I'm saying is put a piece of torch down and heat the middle up and just let it melt in like cheese will that work
No material or membrane wil conform to the shape of the drain by just heating it up. There is a fiber material meshed in between the rubber that gives it strength. I guess without that fibre mesh it will conform but will get very thin
@@happydays454 is just here for laughs
Butcher work,I could do better than that with big torch.
If you have snow and ice there,your drain will leak
Why do you think that
OMG you have to be kidding me what kind of shoemaker are you. You actually post roofing videos of what not to do on your channel. If or when the manufacturer of the material sees this video there warranty on the material will be null and void. Roofing on top of rotting ISO insulation you know very well that when HVAC guys go up there to change ac filters that the screws are going to go throw the new roof you just laid out, and just to save a few bucks you butchered that drain. I assume there is never a roofing inspector on any of you're jod if there is his pockets are full. You should know you are supposed to use a U flow drain insert when roofing over an existing drain.
Your an absolute butcher 😂😂
This is Crap Work. DO NOT DO THIS WAY!!
Dude you should stop making videos😂