Pcv, Evap, EGR, PAIR Reed, Idle up control. There are a few other lines coming off of the plenum I did not mention. If anyone has any question on those I can post another video.
Thank you so much very detailed video. Exactly what I was looking for. Since I deleted my bad egr and charcoal canister I was left with many vacuum lines. Thanks to you I know now what to remove and what to keep.
Viendo de frente el motor es el depósito que se ve del lado izquierdo al fondo es la manguera de abajo la que no hallo dónde es su lugar en si das buena enseñanza a pesar de casi no entender el inglés pero si das a ver a dónde va cada manguera ya estuve viendo cómo 10 tutoriales y eres el primero en dar a conocer mejor que los que lo comentan en español espero me digas dónde va esa manguera gracias .
in your case you're replacing all the lines, but in most cases i use multi colored zip ties to mark all my lines when working on anything with a spaghetti mess of lines. one on the hose and one where it goes. when i run out of colors i use color combos. snip off the ends and leave em on. they look ok and make any future projects easier
You missed the two I need which is at 5:15 below that U shaped hose, to the left of the pair reed and then the one directly under the one your finger is on at 4:04
For this video I was only following the FSM for the most average truck for the exhaust/intake and a couple other systems like evap. I didn't include explanations of the 4wd lines as not everyone has those
I believe I went on amazon and bought an assortment of 4mm 6mm 8mm and 10mm hoses, all silicon and blue so I knew when I changed one. The color coding there was really just so I knew what I had done lol. All hoses were about 10 ft long and about 5 to 15 bucks per dependent on thickness
Hey bro, on 6:45 the line that spilts off to the breaks, i did it the same and noticed my idle goes down to about 700-800 rpm from about 1000 when I press on breaks. Is that normal? I do need to finish off my vacuum lines to the back of the bi-metal vacuum switching valve since the stupid previous owner took them off. You think that could be a cause of it, since it isn't complete?
Hey what's did u do to make that pcv hose make a bend without problems? I'm trying to find the OEM hose and the dealer wants 47 dollars for that small ass hose
I don't remember the brand, I found them on eBay as a last resort. I could not find any original or OEM Cross-over exhaust pipes at the time. However, it is a better option as it does take away the issue of heat collecting at the back of the engine. I would search on eBay for your make and model + headers Here is a link found www.protuninglab.com/hds-4runner88-v6.html?id=1752194785332&gclid=CjwKCAjwwL6aBhBlEiwADycBIImJtv-wjCek9VIs0A38E43jMjT6oQPIuV6tGFzGLizdGXxBoExb_BoCP30QAvD_BwE
Will do! The coolant lines in this truck can be tricky. In about a month or so it will be up. If you want to look at some diagrams you can check out here ether3al.com/93fsm-mobile/
I did the 621 headers on this engine to negate the over heating at the back of engine due to the original cross ovee design. I am in AZ so I need to pass emissions. I hand bent some piping to keep the egr systems intact.
Acabo de cambiarle a mi Toyota Runner 92 4x4 6cil, 3.0 la válvula PVC y efectivamente esa era la falla lo que no le hallo es una manguera que sale de un depósito en la parte de abajo esa no se para donde va y que tiene conectada una manguera en la parte de arriba que va para el tanque de gasolina es como retroceso y una manguera delgadita junto con esa
For the vacuum lines, I searched amazon for blue vacuum hose sizes 4 through 12mm all evens. Found upgr8t brand. They are cheap, solid product. As for the blue silicon coolant hoses. That's from HPS. They make and sell a kit for each model of our truck
Lost at a.c. Lines and the power steering lines.They don't match up right.Try to make a video adding the lines one by one.And go slower ..problems areas the rest a.c. The power steering lines
Hey! I know I go quick, it's actually something I try to do lol I hate long winded videos. If I'm too fast, use the slow feature and mute me once you know what I'm talking about. It should extend the video and show everything I'm talking about If that doesn't work. I do plan in 2026 to restart this channel and go from fsm page one through the whole book. So be on the look out. Sorry if I can't help sooner!
You confuse To much I think if you remove all the hoses and connect 1 by 1. That’s better. I know your are trying to help but you can do better I know just remember. When you don’t know something is like if your are blind thanks. I ll try to understand any way
Thank you so much very detailed video. Exactly what I was looking for. Since I deleted my bad egr and charcoal canister I was left with many vacuum lines. Thanks to you I know now what to remove and what to keep.
This is a life saver. I just lost most of the vacuum lines on the passenger side of the engine bay in a fire and this will greatly help the rebuild
Check out this new fsm someone posted. It might help out!
gvrdeu.org/ToyotaMan.html
Best video on this I've seen so far
Viendo de frente el motor es el depósito que se ve del lado izquierdo al fondo es la manguera de abajo la que no hallo dónde es su lugar en si das buena enseñanza a pesar de casi no entender el inglés pero si das a ver a dónde va cada manguera ya estuve viendo cómo 10 tutoriales y eres el primero en dar a conocer mejor que los que lo comentan en español espero me digas dónde va esa manguera gracias .
Keep the yota videos coming nice truck
Muchas gracias me ajustaron un motor y me dejaron el desmadre de vacíos
in your case you're replacing all the lines, but in most cases i use multi colored zip ties to mark all my lines when working on anything with a spaghetti mess of lines. one on the hose and one where it goes. when i run out of colors i use color combos. snip off the ends and leave em on. they look ok and make any future projects easier
Where did you get replacement hoses? Great video!
"Take the god damned plenum off" that describes half of what end up doing any more.
Pita
I had two lines coming off my power steering pump. Didn't see them on your engine bay but idk my trucks a 90 sr5
Clean engine 👌
I appreciate the love! I'm working on more videos now I'll post soon thanks!
Are you using a hose kit of any kind? Or/and what Size are these hoses.thanks
You missed the two I need which is at 5:15 below that U shaped hose, to the left of the pair reed
and then the one directly under the one your finger is on at 4:04
Should see the vacuum line set up on some Audis !
Perfect job
6.25 are the vacuum lines for the front diff ADD
does your 4wd work? theres a plug in your fender wall that isnt connected.
just saw this too haha was hoing he went into the diff lines with a bit more depth lol
For this video I was only following the FSM for the most average truck for the exhaust/intake and a couple other systems like evap. I didn't include explanations of the 4wd lines as not everyone has those
nice vid man, cleared up a few things for me. what hoses are you using? is that a kit with different diameters?
I believe I went on amazon and bought an assortment of 4mm 6mm 8mm and 10mm hoses, all silicon and blue so I knew when I changed one. The color coding there was really just so I knew what I had done lol.
All hoses were about 10 ft long and about 5 to 15 bucks per dependent on thickness
What type of coolant/vacuum hoses are are you using? Thanks
Where's does the 4WD vacuum lin s go
6.47 where on the brakes?
What kit are you buying for all this hose.
Hey bro, on 6:45 the line that spilts off to the breaks, i did it the same and noticed my idle goes down to about 700-800 rpm from about 1000 when I press on breaks. Is that normal? I do need to finish off my vacuum lines to the back of the bi-metal vacuum switching valve since the stupid previous owner took them off. You think that could be a cause of it, since it isn't complete?
Yes I like that color to better than black, I'm thinking I'm going to sell mine because someone else has been under here
Hey what's did u do to make that pcv hose make a bend without problems? I'm trying to find the OEM hose and the dealer wants 47 dollars for that small ass hose
Thanks for making this video. What exhaust header kit do you have?
I don't remember the brand, I found them on eBay as a last resort. I could not find any original or OEM Cross-over exhaust pipes at the time. However, it is a better option as it does take away the issue of heat collecting at the back of the engine.
I would search on eBay for your make and model + headers
Here is a link found
www.protuninglab.com/hds-4runner88-v6.html?id=1752194785332&gclid=CjwKCAjwwL6aBhBlEiwADycBIImJtv-wjCek9VIs0A38E43jMjT6oQPIuV6tGFzGLizdGXxBoExb_BoCP30QAvD_BwE
@@JaymoTheToyotaPickupGuy thank you! 🤘
Where did you get the Blue Hosing?? What sizes do you have for all the EGR connections??
Can you do one for coolant lines? Specifically the ones between the throttle body and fire wall please
Will do! The coolant lines in this truck can be tricky.
In about a month or so it will be up. If you want to look at some diagrams you can check out here
ether3al.com/93fsm-mobile/
@@JaymoTheToyotaPickupGuy This is an awesome link! Thanks.
Are you going to do a EGR delete and a cold air intake ? 🤔
@MTBTexasBikeRider i did do both of those, however before to check state emissions regs before doing so, it can cause fail
Yeah I’m about to do both on my 4Runner it’s legal to do it now it’s over 25 years old! Thanks great video! 👍😎🤘
Thank you bro
Did you use any complete kits for the video that I can buy online? If so where did you buy them?
Lce engineering has complete kit
How did you seal your coolant/water bypass outlet?
@@Sm0k3ydabear04 I believe I used that toyota brand sealant, the white tube with a black sealant gel. I may be wrong
good looking engine too. i would like headers if i continue with the 3vze. i have some videos where ive done the egr delete. no smog testing in TN
I did the 621 headers on this engine to negate the over heating at the back of engine due to the original cross ovee design. I am in AZ so I need to pass emissions. I hand bent some piping to keep the egr systems intact.
Great video Jaymo. however, where did you get those silicone lines? they look nice.
Random sellers on Amazon, I just googled something like"2mm silicon vacuum hose"
@@JaymoTheToyotaPickupGuy did you cut it or they come already come cut for the size ?
How did y make the bend work on the pcv hose?
Acabo de cambiarle a mi Toyota Runner 92 4x4 6cil, 3.0 la válvula PVC y efectivamente esa era la falla lo que no le hallo es una manguera que sale de un depósito en la parte de abajo esa no se para donde va y que tiene conectada una manguera en la parte de arriba que va para el tanque de gasolina es como retroceso y una manguera delgadita junto con esa
donde trae la valvula pvc
what hole size are the throttle body line?
@@Ru_90 4mm I believe
If you were to conduct a leak test which intake line would you use?
what is the name of program or website your laptop is on
gvrdeu.org/ToyotaMan.html
ether3al.com/93fsm-mobile/ also here but not as good as gvrdeu
what kit/lines did you use? link?
For the vacuum lines, I searched amazon for blue vacuum hose sizes 4 through 12mm all evens. Found upgr8t brand. They are cheap, solid product.
As for the blue silicon coolant hoses. That's from HPS. They make and sell a kit for each model of our truck
Do you know where I can download that diagram/manual that you have on your laptop? Thanks in advance.
Yes link is below
www.ether3al.com/93fsm-mobile/
Lost at a.c. Lines and the power steering lines.They don't match up right.Try to make a video adding the lines one by one.And go slower ..problems areas the rest a.c. The power steering lines
Hey! I know I go quick, it's actually something I try to do lol I hate long winded videos. If I'm too fast, use the slow feature and mute me once you know what I'm talking about. It should extend the video and show everything I'm talking about
If that doesn't work. I do plan in 2026 to restart this channel and go from fsm page one through the whole book. So be on the look out.
Sorry if I can't help sooner!
Sir what program or pdf are you using?
ether3al.com/93fsm-mobile/
Right here my guy!
Uh that's the right valve cover.
You confuse To much I think if you remove all the hoses and connect 1 by 1. That’s better. I know your are trying to help but you can do better I know just remember. When you don’t know something is like if your are blind thanks. I ll try to understand any way
For anyone wondering silicone hose Ucreative 6PCS 5FT High Performance Automotive Silicone Vacuum Tubing Hose line Kit 3mm 4mm 5mm 6mm 8mm 10mm Inner Diameter (Black) a.co/d/aQwEg5Z
Bro where did you get your blue vacuum lines? Did you have to offer specific size lines? What sizes?
LC engineering 3vz silicone vacuum hose kit for if you haven’t found it yet